3. Find the values of resistance R andcapacitance C in the circuit, if =1.442 33.959I A.130 sH40 V. 20 KHz4. In RL circuit, a voltage of 10V at 75 Hzyields 60 mA while at 25 Hz yields 100mA at the same voltage. Find the valuesof circuit constants. At what frequency willthe value of the impedance be twice thatat 25HZ?

As per company guidelines we are supposed to answer only one question. Kindly repost other questions…

Answered: 3. Find the values of resistance R and…

Engineering

Electrical Engineering

3. Find the values of resistance R and capacitance C in the circuit, if I = 1.442 33.959 A. 130 s 40 V 20 KHz

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A resistor, an inductor, and a capacitor are connected in parallel to an ac source with voltage amplitude V and angular frequency v. Let the source voltage be given by v = Vcosvt. (a) Show that each of the instantaneous voltages vR, vL, and vC at any instant is equal to v and that i = iR + iL + iC, where i is the current through the source and iR, iL, and iC are the currents through the resistor, inductor, and capacitor, respectively. (b) What are the phases of iR, iL, and iC with respect to v? Use current phasors to represent i, iR, iL, and iC. In a phasor diagram, show the phases of these four currents with respect to v. (c) Use the phasor diagram of part (b) to show that the current amplitude I for the current i through the source is I = √(I2R) + (IC - IL)2 . (d) Show that the result of part (c) can be written as I = V/Z, with 1/Z = √ (1/R2) + [ωC - (1/ωL)]2.
A coil of inductance 100 mH and resistance 800 ohm is connected in parallel with a variable The capacitor is across a 12V, 5 kHz supply. Determine for the condition when the supply current is a minimum: (a) the capacitance of the capacitor, (b) the dynamic resistance, (c) the supply current, and (d) the Q-factor
Question 3 For the circuit shown below: (A) Find the frequency (in radians per second) at which the impedance Zab is purelyresistive.(B) Find the value for Zab at the frequency found in (A).
a) What is the time domain expression for the current? b) If the load impendance is created by an inductor with value L=375 mH, find the phaser voltage Vx? c) If the load impendance is created by a capacitor with value C=16.7 uF, find the phaser voltage Vx?
A circuit is designed with an AC source of max voltage 12 and frequency 60 Hz. The circuit has a resistance of 1050 Ohms, an inductance of 0.06 Henrys, and a capacitance of 0.009 coulombs per volt. - omega for source in rad/s? - omegaR for circuit? -XL? -XC? -phi in radians? -Z? -imax?
In the circuit in the figure, Vcc= 18 V, Rs1 = 0.9 kohm, Rohm = 0.5 kQ, R1 = 75 kohm, R2 = 15 kohm, RC = 2.2 kohm, RE = 1 kohm and B = 120. It is also known that Cwi = 6 pF, Cwo = 10 pF, Cbc = Cu = 7 pF, Cbe = C = 44 pF and Cce = 11 PF. Accordingly, considering the frequency response of the circuit, what would the high cutoff frequency (fH) be? NOTE-1: The output impedance of the transistor is ro = 20 k and will be taken into account in the calculations. NOTE-2: high frequency dependence of hfe, B. will be taken into account.
In the circuit in the figure, Vcc= 18 V, Rs1 = 0.9 k2, Rs2 = 0.5 kQ, R1 = 75 kQ, R2 = 15 kQ, RC = 2.2 kQ, RE = 1 k and B = 120. It is also known that Cwi = 6 pF, Cwo = 10 pF, Cbc = Cu = 7 pF, Cbe = C = 44 pF and Cce = 11 PF. Accordingly, considering the frequency response of the circuit, what would the high cutoff frequency (fH) be? NOTE-1: The output impedance of the transistor is ro = 20 k and will be taken into account in the calculations. NOTE-2: high frequency dependence of hfe, B. will be taken into account.
Derive the following. Assume an ideal current source a.) Frequency Response
A series RLC circuit having values of ? = 250Ω, ? = 3??, and ? = 4?? is shunted across a sinusoidal voltage given by the expression ?(?) =200 sin(200?? − 16°) ?. Look for the following: a. The equivalent impedance of the connection b. The phasor and instantaneous current flowing through the connection c. Draw the phasor diagram of the supply voltage and the total current. What is the phase difference of the two? d. What is the phasor and instantaneous voltage across the capacitor? e. If a 75?? capacitor is shunted across the load, what is now the value of the equivalent impedance in the connection?
An RLC circuit (has resistance and reactive elements) supplied by a 60Hz power source is found to have a lagging power factor (PF). What can you say about the relative contributions of the resistance (R), XL inductance, XC capacitance & resistance/reactance (ratio) utilized in this circuit at the 60Hz frequency? (min two statements – major reactive element & comparison to Resistive element)
In an RLC series circuit, the voltage amplitude and frequency of the source are 100 V and 500 Hz, respectively, an R = 500Ω, L = 0.20 H, and C = 2.0μF. (a) What is the impedance of the circuit? (b) What is the amplitude of the current from the source? (c) If the emf of the source is given by v(t) = (100 V) sin 1000πt , how does the current vary with time? (d) Repeat the calculations with C changed to 0.20μF.
How does the characterization of the circuit as a Thévenin or Norton's equivalent simplify the prediction of the response of a circuit? Consider an AC wall plug. Is it better to model this source as a Thévenin equivalent or as a Norton Equivalent? Explain why. Again consider an AC wall plug. Is this source more like an ideal voltage source or like an ideal current source? Explain why.