A load of 1000 KW is connected at the receiving end of a 3 phase transmission line 60 km long. The parameters of the transmission line are given by r = 0.09 Q/km and x = 0.8 Q/km. The voltage at the receiving end of the transmission line is rated at 21 kV. If the machine is working at 0.65 power factor lagging. Determine: a) The series reactance of the transmission line b) Sending end line voltage c) Percentage Voltage regulation d) Percentage Efficiency

A load of 1000 KW is connected at the receiving end of a 3 phase transmission line 60 km long. The parameters of the transmission line are given by r = 0.09 Q/km and x = 0.8 Q/km. The voltage at the receiving end of the transmission line is rated at 21 kV. If the machine is working at 0.65 power factor lagging. Determine: a) The series reactance of the transmission line b) Sending end line voltage c) Percentage Voltage regulation d) Percentage Efficiency

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.26P: A small manufacturing plant is located 2 km down a transmission line, which has a series reactance...

See similar textbooks

Similar questions

1/In the Transmission Line Simulator, the Transmission Line is connected in Nominal-Pi Circuit. Select one: True False
A dc transmission facility is modeled by the approximate series circuit shown below. If the load voltage is known to be Vload= 458.3 kilovolt (kV) what is the power loss in the line in megawatt (MW)?
a) You have been employed as an electrical engineer by a power transmission company to design a short transmission line to supply power to a light-industrial load consumer with power system specification as follows, a 3-ph, 60Hz overhead short transmission line with a line-to-line voltage of 23KV at the load end, line impedance of 2.48 ±j6.57Ω/phase, the industry has a cumulative consumption of 9MW with a power factor of 0.85 of lagging as a result of several induction motor on its production lines.As part of the regulations for connections to the grid, you are to provide justifications and values to the Energy Commission of Ghana.(i) What would be value of the voltage between the live conductor and the neutral, between live and live voltages at the industrial premises of the factory?(ii) What load angle would expect the factory to be operating at?
A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:10), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (20:1) and a load with magnitude Z=10 Ohm and angle =30 degree the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the 1/per-unit impedance of the load 2/per-unit current in the line 3/ per-unit real power absorbed by the load
S.1) The serial impedance per phase of a three-phase 45 km energy transmission line is 2 + j4 / phase. A load with a power factor of cos2 = 0.8 forward is fed from the end of the line. Since the line voltage at the beginning and end of the line of the energy transmission line is wanted to be kept constant at 115 kV, a) Active and reactive powers drawn from the beginning and end of the line, b) Calculating the power consumed along the energy transmission line and the efficiency of the line. S.2) Line constants of an energy transmission line are given as A = D = 0.8746 + j0, B = 0 + j128.34, C = j0.0018316 S. At the beginning of the line, it is desired to write 1920 MW active power and 600 MVAr reactive power lines under 7650kV line voltage. According to this business, a) Calculate the line end magnitudes (U2, I2 and P2). b) What value does the end voltage take when the load fed from the end of the line is deactivated? S.3) The length of a phased energy transmission line with a…
A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:10), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (20:1) and a load with magnitude Z=10 Ohm and angle =30 degree the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the per-unit impedance of the load. Calculate the per- unit current in the line Select one: a. 1.43 A b. 0.569 A c. None of the above d. 2.01
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.
The length of a transmission line is (1000/3) kilometers. For this transmission line r=0.15 ohm/km x=0.8 Ohm/km y=5 * 10^-6 S/km given in the form. At the end of the line (36) MW is drawn and the end-of-line voltage is (220) kV. power factor: 0.95 (back) a. Assuming the line as a short line, calculate the VS and IS values with their angles. b. A, B, C, D by accepting the line as a mid-length line and using the "T" model approach. Calculate the parameters (Vs Is calculation is not needed) C. Calculate only parameter A, assuming the line as a long line.
A three-phase transmission line receiving end voltage is rated at 21 kV. A load of 1500 KW is connected at the receiving end of the transmission line 70 km long. The parameters of the transmission line are given by r = 0.09 Ω/km and x = 0.8 Ω/km. If the machine is working at 0.65 power factor lagging. Determine a) The series reactance of the transmission line b) Sending end line voltage c) Percentage Voltage regulation d) Percentage Efficiency
A 500 kV, 60 Hz uncompensated three-phase transmission line is 500 km long. The line has three ACSR 1113-kcmil (Finch) conductors per phase with parameters Current carrying capability of single ACSR 1113-kcmil (Finch) conductor is 1,110 A. Calculate the theoretical maximum (steady state stability limit) real power that this line can deliver and compare with the thermal limit of the line. Assume VS = VR = 1.0 per unit and unity power factor at the receiving end.
-) The active and reactive power drawn by the mixer fed from a 230 Vrms, 50 Hz single phase AC network was measured as 600 W and 100 VAR, respectively. According to this information: a) Calculate the apparent power drawn from the network? b) Calculate the current drawn from the network? c) Calculate the cos(a).
The area of an interconnected power system has two units operating on economic dispatch. The variable operating costs of these units are given by C =8P +0.009P2 11 1(R/h) and C = 10P + 0.008P2 where P1 and P2 are in MW. The transmission losses for the area are given by ? = 1.5 × 10−4?2 + 2 × 10−5? ? + 3 × 10−5?2 , MW ?1122 2 2 2 (R/h,) Determine the following when the area λ = 16.00 R/MWh: a. The output of each unit b. Total transmission losses c. Total load demand d. Total operating cost