3. From the figure shown, determine the force members CD, DM, and ML using the method of sections. Also state the nature of the force whether it is in tension or compression. Assume that support A is a pin and support I is a roller. 12 kN 12 kN 12 kN 12 kN 12 kN 6 kN 6 kN 16 m B 3 m IN K

3. From the figure shown, determine the force members CD, DM, and ML using the method of sections. Also state the nature of the force whether it is in tension or compression. Assume that support A is a pin and support I is a roller. 12 kN 12 kN 12 kN 12 kN 12 kN 6 kN 6 kN 16 m B 3 m IN K

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.113P: The pins at the end of the retaining-ring spreader fit into holes in a retaining ring. When the...

See similar textbooks

Related questions

Q: 1.ldentify the zero force members at the truss 2. Determine the force at member AB using B method of…

A: The free body diagram of the truss is as follows:

Q: 4/6 Calculate the force in each member of the loaded truss. E D -2 kN 3 m 3 m 3 m C B

A: Force system of truss Here assume that the support reaction at joint A is RA in vertically upward…

Q: The truss is supported by a pin connection at A and a roller at E. It is loaded as shown. Use the…

Q: F.. :) For the truss shown below, determine the bar force of AB and AD. Also indicate if these…

Q: 4 @ 4m=16m- A B C D G 60 kips L. -5@ 3m=15 m-

Q: 3. Compute all the bar forces, indicate if the members are in tension or compression. Length are in…

A: GIVEN DATA - A PLANE TRUSS GIVEN WE HAVE TO FIND FORCE IN ALL BARS CONCEPT USED - METHOD OF JOINTS

Q: O The truss is subjected to the loading condition as shown in the Figure Q4.1. Identify and…

Q: The simple truss is loaded by a system of forces as shown in the figure. The truss is supported by a…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Q: Determine the horizontal and vertical components of force which the pin at B exerts on member BC of…

A: The free body diagram of the beam is as follows:

Q: L- - B D 3.6 m H A K M F F F F F =D4m and F=1000 kN.

Q: 3. Using the method of joints, calculate the forces in members and state whether they are in tension…

Q: Determine the forces acting in members A, B and C for the truss framework structure below when a 200…

A: Using method of joints to determine the forces in each member.

Q: The truss shown beiow is supported by a pin support at H and a roller support at P The positive sign…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Q: 3. Compute all the bar forces, indicate if the members are in tension or compression. Length are in…

Q: Two members, each consisting of straight and 168-mm radius quarter-circle, are connected as shown…

Q: 3) Determine the force in members EF and GI of the truss shown. The truss system is pin connected at…

Q: 1. Find the maximum value of P that may be applied to the Fink Truss, if the maximum loads permitted…

Q: 1.ldentify the zero force members at the truss 2. Determine the force at member AB using method of…

Q: The truss, shown in the figure, is being held in place by a pin at H and a roller at A. Use the…

Q: 3. Determine the force in each member of the truss in terms of the external loading and state if the…

Q: -2 m- 40 kN -2 m- 50 kN H I A D -2 m- C 1.5 m -30 kN 1.5 m B 40 kN 1.5 m ļ

Q: shown in figure, determine: Pif the forces in member (Compression). A. at A and G. members BC, and…

A: Consider Joint Method For support reaction ∑MA = 0 (Positive)(-4 ×2)- ( 5 × 4) - (8 × 8) - (6 ×…

Q: is being 6-66 The garage door ABCE shown in Fig. raised by a cable DE. The one-piece door is a…

A: Given data

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

Q: C 2 m- Use the method of sections to calculate the axial force in members AC and BC. Enter your…

Q: Answer the following questions * 1.ldentify the zero force members at the truss 2. Determine the…

A: Where there is a two force no-collinear member joint with no external force, the two forces are zero…

Q: 20 kg is supported by two inclined planes, as shown. Sketch

A: given:mass of cylinder m=120kg

Q: The frame shown in Figure is supported by a hinge at E and a roller at D. Compute the horizontal and…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Q: Answer the following questions * 1.ldentify the zero force members at the truss 2. Determine the…

Q: 3. Determine the force in each member of the truss. State if the members are in tension or…

Q: In the figure shown, the frame is supported using a hinge in point A and a roller in point B. The…

Q: 2) Determine the force in each member of the truss, and state if the members are in tension or…

A: For the given truss To determine force in each member of the truss and state if the member is…

Q: Need answer please

Q: The truss, shown in figure (3), is being held in place by a pin at H and a roller at A. Use the…

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

A: Data given- F = 600 N Force in member CE ?

Q: QI: Determine the force in members EG, HG, and HJ in the given frame as shown in figure 1 using…

A: The supports are replaced by reactions as shown in Figure below. Applying conditions of…

Q: 1. The truss shown below is supported by a pin at joint A and a roller at joint K. Find the forces…

A: given; lets take reaction force at A=RAlets take reaction force at L=RLAG=12mAM=5mlake tension force…

Q: METHOD OF SECTIONS - PROBLEMS SOLUTION PROBLEM NO.1: Determine the axial forces in members CD, CJ,…

Q: Solve the following problems by the method of sections. State whether the members are in tension or…

A: Consider the free body diagram shown below for the for the given truss. In triangle CF’B, Also,

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Q: Find the member forces in: A. Indicate the zero force members. B. Find the member forces in CE, DE,…

A: Given:- F1=100lb F2=300lb AB=12 ft BD=DF=FH=9ft To find:- a) Zero force members b) Member forces for…

Q: Solve the following problems by the method of sections. State whether the members are in tension or…

A: The free-body diagram of the given truss which the section cut is shown below. Since there are no…

Q: Solve the following problems by the method of sections. State whether the members are in tension or…

A: Moment acting about point A is Dx4 m=P13 m+P23 m+3 m+3 mDx4=53+39Dx=10.5 kN Force acting at A in x…

Q: Use the method of Joints to calculate the force in each member of the loaded truss illustrated and…

Q: In the structure shown, force F is applied at point A at an angle of 6 in the direction shown. Pins…

Q: 4) For the truss, which shows the reactions found at the supports at A and E, answer the following:…

A: Given: The truss is shown below:

Q: Determine the horizontal and vertical components of force which the pin at B exerts on member BC of…

Concept explainers

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.

Question

Solve the problem according to what is asked directly in the problem.

3. From the figure shown, determine the force members CD, DM, and ML
using the method of sections. Also state the nature of the force whether it
is in tension or compression. Assume that support A is a pin and support
I is a roller.
12 kN
12 kN
12 kN
12 kN
12 kN
6 kN
6 kN
6 m
B
3 m
¡M
K
-4 m-4 m--4 m--4 m--4 m-4 m-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

We want to use the method of sections for this problem to find the force in members LK, KC, and CD of the Pratt truss. Take that P1 = 20 kN , P2 = 33 kN and P3 = 39 kN B) Determine the force in the member CD, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.
We want to use the method of sections for this problem to find the force in members LK, KC, and CD of the Pratt truss. Take that P1 = 20 kN , P2= 33 kN and P3 = 39 kN A) Determine the force in the member KC, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.
As per the crane shown in the Figure. Determine the force member at BD.
Find the forces in all the members of the truss shown and determine whether they are in tension or compression. Make a summary and draw a FINAL FBD. P1= 14.1 kN, P2= 29.7 kN
The pin at O can support a maximum force of 3.5 kN. What is the corresponding maximum load L which can be applied to the angled bracket AOB? A. 0.541 kN C. 2.632 kN B. 1.676 kN D. 3.091 kN
This structure is supported by a roller joint on the left and a pin joint on the top. Two loads, P have similar magnitudes of P = 650 N and the angle θ = 40°. The length L of both members is 1.5 m. The vertical load acts at the midpoint of the horizontal member. Solve for the reaction forces at the roller and pinned joints.
The pins at the end of the retaining-ring spreader fit into holes in a retaining ring. When the handgrip is squeezed, the pins spread the retaining ring, allowing its insertion or removal. Determine the spreading force P caused by the 8-lb forces applied to the handgrip.
The truss, shown in figure (3), is being held in place by a pin at H and a roller at A. Use the method of joints or the method of section to determine the forces in members BD and CD. he force P=87 at joint M in KN.
Solve Prob. 6.39 for P = 0 and Q = (-900 N)k.(Reference to Problem 6.39):The truss shown consists of nine members and is supported by a ball-and-socket at B , a short link at C , and two short links at D. (a) Check that this truss is a simple truss, that it is completely constrained, and that the reactions at its supports are statically determinate. (b) Determine the force in each member for P= (-1200 N)j and Q = 0.
Determine the force in each member of the loaded truss. All triangles are 3-4-5. Enter a positive number if the member is in tension, negative if in compression.
The truss is supported by a pin connection at A and a roller at E. It is loaded as shown. Use the picture below to determine the forces in members CD, CF, GF. Enter each value in separate questions and report all answers in kN but do not enter units. Report positive values for members in tension and negative values for members in compression. Determine the force in CD, CF and GF with appropriate units. Thanks.
Determine the angle that will yield a maximum force uh member BC, along with magnitude and nature of this force. Note: use method of sections and show solution. Answer should be 45° & BCmax = 168 kN