Q2) The figure shows a cantilever consisting of steel channel size 127 mmx64 mm. Using superposition, find the deflection at B and the maximum stress in the beam. Take the magnitude of force (F) to be 1.3 kN, L = 3 m, and a = 1.8 m. Calculate the deflection at point B in (mm). Use E= 207 GPa. F I kN/m B A

Q2) The figure shows a cantilever consisting of steel channel size 127 mmx64 mm. Using superposition, find the deflection at B and the maximum stress in the beam. Take the magnitude of force (F) to be 1.3 kN, L = 3 m, and a = 1.8 m. Calculate the deflection at point B in (mm). Use E= 207 GPa. F I kN/m B A

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

THE ANSWER MUST BE IN FOUR DECIMAL PLACES the steef shaft shown in figure rotates at 4Hz with 35 KW taken off at A, 20 kW removed at B and 55 kW applied at C. Using G=83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C
Refer figure 1: Determine the deflection (delta) in mm at point B. Use E = 200 GPa and I = 2100 mm^4 What is the vertical support reaction at the hinge as shown in the figure below.
A steel plate 2.2 m x 1.4 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the vertical displacement of the steel plate when suspended if the sling cable is 55 sq.mm. in area. The correct answer is 2.84. Show solution.
Determine the force P needed to pull the 50-kg roller over the smooth step. Take θ = 30°.
Determine the following unknowns on the beam shown below using Conjugated-Beam Method. Consider 250 mm x 250 mm Section and E = 200 GPa. Note: a = 4.5 m b = 33.0 kN/m c = 13 kN Find the following A. Vertical reaction at C in kN. B. Moment reaction at C in kN-m. C. Deflection at point B in mm. D. Maximum deflection on the beam in mm.
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
Refer to the beam loaded as shown. (a)What is the Value of horizontal reaction at the fixed support?(b)What is the value of resulting couple at A?
Since the beam M in the figure is under the effect of simple bending moment, calculate the bending stress and shear stress values at the A, B and C points. h = 400mm b = 140mm and M = 150KNm
a. Calculate the moment of inertia (I) of the given cross–section b. Calculate the first moment of area (Q) at certain depth by using 25 mm increments. c. Calculate and draw the horizontal shear stress distribution of the beam at 0.2 m from the left support
What is the area of the tube? What is the total length of the median line? What will be the result shear flow of the object? The shearing stress value will be The angle of twist will be
Determine the following unknowns on the beam shown below using Conjugated-Beam Method. Consider 250 mm x 250 mm and E = 200 GPa. Note: a = 4.5 m b = 33.0 kN/m c = 13 kN Find the ff. A. Vertical reaction at C in kN. B. Moment reaction at C in kN. C. Deflection at point B in mm. D. Maximum deflection on the beam in mm.
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?