3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross sectional area of 400 mm². Ea=70 GPa. Use the Force Method 100 mm -100 mm- 800 kN/m 125 mm 800 kN/m

3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross sectional area of 400 mm². Ea=70 GPa. Use the Force Method 100 mm -100 mm- 800 kN/m 125 mm 800 kN/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simple wooden AB beam (see figure 2) supportsa uniform load of 24 kN / m (includes weightcharacteristic of the beam), with a length L = 1.75m and sectionrectangular cross section with width of 200mm and height250mm. Determine:a) Reactions and shear diagram.b) Using the maximum shear force, find theshear stress in:to. The centroid.b. At a distance of 62.5mm from the centroid.c. At the ends of the cross section.c) Draw the shear stress diagram withall values obtained.
Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places Structural Theory a. Determine the vertical reaction R₂ in KN. b. Determine the shear at midspan between vertical supports in KN c. Determine the maximum factored load moment in the beam in KN.m
The wooden members in the simple truss below have the following capacity: Shear parallel to grain = 1 MPa, Compression parallel to Grain = 11MPa, Compression perpendicular to Grain = 5 MPa 1. Find the minimum safe x. a. 73 mm b. 160 mm c. 148 mm d. 112 mm 2. Find the minimum safe y. a. 15.97 mm b. 19.45 mm c. 9.14 mm d. 18.28 mm 3. Determine the stress in member AC. a. 1.13 MPa b. 1.258 MPa c. 1.224 MPa d. 1.04 MPa
A joint in a wooden structure shown has an applied loadF = 50 kN along the axis of the slanted member with anangle of 30°. Determine the bearing stress developedalong the plane ABC.Answer: σb ___________________
A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
Determine the tension at AC. A. 55.23 kN B. 52.53 kN C. 32.55 kN D. 25.35 kN
A simple pin-connected truss is loaded and supported asshown in Figure P1.12. The load P is 200 kN. All members of thetruss are aluminum pipes that have an outside diameter of 115 mmand a wall thickness of 6 mm. Determine the normal stress in eachtruss member. Assume truss dimensions of a = 12.0 m, b = 7.5 m,and c = 6.0 m.
The steel shaft with two different diameters rotates at 4.2 Hz. The power supplied to gear C is 68 kW, of which 42 kW is removed by gear B. Find the maximum shear stress (in Pa) in the shaft if d = 58.1 mm, h = 60.6 mm, L = 3.9 m, M = 2.1 m, and G = 83.49 Gpa. Round off the final answer to two decimal places
Q.1 A structure is supported by braces each of which transfersa load P = 160 kips to the base of a column as shown infigure. A cap plate at the bottom of the brace distributesthe load P to four flange plates through a pin to twogusset plates. Diameter of Pin and thickness of flangeplate and gusset plate are provided in figure. Determine(a) The average shear stress in the pin.(b) The average bearing stress between the flange plates andthe pin.(c) The normal axial stress in gusset plate. Assume thatgusset plate is 4 inch wide. Note: Please answer the section c as well
A 0.400 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.9 in., and the load applied to each pulley is P = 51 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft.
Take 2 KN/m in place of 1.5. Determine support reaction
The 1.25-in diameter steel shaft BC is built into the rigid wall at C and supported by a smooth bearing at B. The lever AB is welded to the end of the shaft. Determine the force P that will produce a 2-in. vertical displacement of end A of the lever. What is the corresponding maximum shear stress in the shaft? Use G = 12 x 106 psi for steel, and neglect deformation of the lever. Please write legibly, thank you