A cylindrical tank 400 mm in diameter, discharges water through a 30 mm orifice under a constant head of 5 meters (with reference to the orifice centerline). If it takes about 10 seconds to fill 42 liters of a volumetric measuring tank. Use g =9.8m/s² What is the theoretical flowrate (m³/s)?

A cylindrical tank 400 mm in diameter, discharges water through a 30 mm orifice under a constant head of 5 meters (with reference to the orifice centerline). If it takes about 10 seconds to fill 42 liters of a volumetric measuring tank. Use g =9.8m/s² What is the theoretical flowrate (m³/s)?

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter9: Mass And Mass-related Variables In Engineering

Section: Chapter Questions

Problem 37P

See similar textbooks

Related questions

Q: The platform is rotating such that, at any instant, its angular position is 0 = (0.21t³ -0.22t² + 3)…

Q: through the distance from the sur s through distance 'y' at the leading e

A: solution of above problem is below:

Q: Oil (SG oil = 0.95) flows at 200 L/s through a 200mm diameter pipe, 500m long. Friction factor is…

A: To Determine a) the head loss, hf b) the pressure difference between the endpoints of the pipe, ΔP

Q: A solid shaft has length and diameter 'L and Drespectively. A hollow shaft of length L. external…

Q: Prob. 3.4-6. A magnesium-alloy rod (E = 6.5 x 10 ksi) o × 11 15 x diameter d. 1 in. is encased by a…

Q: 6 m B 60 KN ļº 60 kN P 60 KN 4 panels at 8 m = 32 m EA = constant Sw E Determine the force in member…

A: Given values: Consider the truss given. Using method of joints and method of sections the unknown…

Q: At a traffic intersection, cars and buses arrive randomly according to independent Poisson processes…

A: Given data- Average rate-λcar=4 veh/hAm=0.6-0.9for 30 min-λcar=2 vehicleλbar=2 veh/hfor 30…

Q: Determine all the support reaction of the given figure A W (KN/m) L b B

Q: The end of a cantilever I beam supports forces from three cables. a) If P = 0, determine the…

A: Given :

Q: The 3-m-wide barge shown weighs 20 kN empty. It is proposed that it carry a 250 kN load. Predict the…

Q: In a drained tri-axial compression test, a sample of sand fails at deviator stress of 150 kPa under…

Q: -2m- IC Im D -2 m e shear and bending-moment diagrams and determine the maximum absolut e bending…

Q: In a triaxial unconsolidated undrained (UU) test on a saturated clay sample, the cell pressure was…

A: given cell pressure=100 kPadeviator stress=150 kPa

Q: Determine the required spacing of 10mm U- stirrups at the left end of the simple beam carrying a…

A: Answer We know that the critical section for shear is at a distance 'd' from the support. Calculate…

Q: onents for the rigid body in the figure.

Q: or what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be…

Q: A beam with a guided support and 10 ft span supports a distributed load of intensity q = 642 lb/ft…

A: Given data: q=642 lb/ftMo=268 lb-ft

Q: The hydrostatic equation is used to predict pressure variation in a fluid with constant density.…

A: Given data in question Hydrostatic equation Height Density To find out Which among is correct

Q: A city discharges 100 cumecs of sewage into a river, which is fully saturated with oxygen and…

Q: 9m 6m ENC 40KN A 120 KN 40KN hinged 6m 25m hinged B 25m C hinged Determine all the supports…

A: Using equilibrium equation

Q: A rectangular lot was measured using a 50-m tape which was found to be 0.010 m too short. If the…

Q: 8 and 9 please :) ill thumbs up

A: Given data in question Statements To find out Which among options are correct

Q: gh a horizonta of the tube w

Q: The water in a reservoir is restrained by a triangular wall. The total force (hydrostatic +…

Q: The compound shaft, compose of steel, aluminum, and bronze segments, carries the two torques shown…

Q: Draw the shear and bending-moment diagrams for the beam and loading shown, and determine the maximum…

A: Given:- A beam is loaded with two-point loads The magnitude of the point loads = 300 N To…

Q: Describe the method of conducting surveying fieldwork for flood cases in civil engineering…

A: There are various methods for carrying out field survey for flood cases for flood management.

Q: A particles moves in a straight line with the acceleration shown in the motion curve given. Knowing…

A: Given data: vo=-18 ft/sec

Q: Prob. 3.4-16. A uniform circular cylinder of diameter d and length L is made of material with…

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

Q: Q4(2). The beam is pin-supported at A, and supported by a roller at B. The lengths are 1.7 m and 2 =…

Q: The piezometric and velocity head variation for flow through a venturi section is shown below.…

Q: you show me the more clearer solution?

Q: Henry's law constant for transferring 02 from air into water, at room temperature, mmol - is 1.3…

A: Given data: Henry's law constant at room temperature, k = 1.3 m-mollt-atm Partial pressure, P = 0.21…

Q: For the frame shown, determine the Horizontal component of the force at E and A. Vertical component…

Q: A wastewater sample contains two nitrogen species, namely ammonia and nitrate. Consider the atomic…

A: Given data: A wastewater sample contains two nitrogen species, namely ammonia and nitrate.

Q: Consider joint C next. The Free-Body diagram is shown. All members are assumed to be in tension. Use…

Q: Determine all the support reaction of the given figure A 500 lb/ft 30ft C 15ft D 6k 20ft 10ft 10k…

Q: A rectangular lot was measured using a 50-m tape which was found to be 0.010 m too short. If the…

A: Given data Standard length of tap (l) = 50 m Length is too short by 0.01m Measured length (Lm) =…

Q: 5. The drill shaft of an oil well is made of A992 steel (E = 29000 ksi). The shaft extends 1200 ft…

Q: o 59.1 mm thick rubber pads are bonded to three steel plates to form the shear mount is required to…

A: GIVEN :w =100mml=153mmν =0.48 E = 1.9 GPa∆ = 4.56mmP =?t = 59.1 mm E = 2G (1 -ν)1.9 = 2G(1-0.48)G =…

Q: The pump-turbine system in the figure draws water from the upper reservoir in the daytime to produce…

Q: The length of the weir L (in feet):

Q: The bent rod shown below consists of two straight parts along x and y- axes and a half-circle in…

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: Question- An uncompacted heap of soil has a volume of 10,000 m³ and void ratio of 1. If the soil is…

A: Given data- For uncompacted soil-Volume V1=10,000 m3void ratio e1=1For compacted soil-Volume V2=7500…

Q: A magnesium-alloy Prob. 3.4-6. diameter d rod (E = 6.5 x 10 ksi) of 15 x 1 in. is encased by a brass…

Q: Considering the following figure with flow from A to D, compute the total head loss front A to D if…

A: Given: discharge, Q = 1700l/s =1.7m3/s For Pipe AB , Length, L = 1000m , dia D = 900mm For Pipe 2, L…

Q: Find flow speed and depth of water above a hump in the Figure Q3. Calculate critical depth, Froude…

Q: O Application of the momentum equation to fluid flow problems is analogous to the use of the…

A: This question is related to the Fluid Mechanics. In this question we fill the blanks. As per fluid…

Q: A simply supported wood beam AB with span length L = 3.5 m carries a uniform load of intensity q =…

A: Given data in question UDL Span member length Cross section To find out Maximum flexural stress

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

A cylindrical tank 400 mm in diameter, discharges water through a 30 mm orifice
under a constant head of 5 meters (with reference to the orifice centerline). If it takes
about 10 seconds to fill 42 liters of a volumetric measuring tank. Use g =9.8m/s²
What is the theoretical flowrate (m³/s)?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

An open cylindrical tank 800mm in diameter and 2000mm high contains water to a depth of 1.6m. It is rotated about its vertical axis at 13 rad/s. How many liters of water are spilled? Use density of water as 1000kg/m3 and specific weight as 9.81kN/m3
A tank is in the shape of an inverted cone, having height h = 2.5 m and base radius r = 0.75 m. If water is poured into the tank at a rate of 15 L/s, how long will it take to fill the tank? Water flows into a cubical tank at a rate of 15 L/s. If the top surface of the water in the tank is rising by 1.5 cm every second, what is the length of each side of the tank?
A cylindrical tank having a diameter of 3.5m and a height of 10m is full of water. there is an orifice at the bottom of the tank having an area of 0.025 m^2. if the tank has a coefficient of discharge of 0.60, how long will it take to empty the tank in minutes?
Water flows through a pipe 25 mm in diameter at a velocity of 6 m/s. Determine whether the flow will be laminar or turbulent assuming that the dynamic viscosity of water is taken as1.30 × 10−3 kg/ms and its mass density as 1000 kg/m3. If oil of specific gravity 0.9 and dynamic viscosity 9.6 × 10−2 kg/ms is pumped through the same pipe, what type of flow will occur?
Instead of a 0.9 cm diameter water pipe, a 2.3 cm diameter pipe was installed. 8.6 liters of water per second was obtained from the previous water pipe. How fast does the water come out of the new line in liters per second? Other aspects related to water pipes are assumed to remain unchanged.
Water circulates at 20 °C (p = 1000 kg/m3) in the form of *Y* of the following figure. The flow rate (inflow) in section 1 is 5300 N/s, and the speed in section 3 is 5 m/s. Calculate: a) the speed in section 1, b) the flow Mass in Section 3, c) the speed in section 3
Calculate the hydraulic power of a pump (kW) that transfers water at 300 m3/hr to a tank at an elevation of 11 m. The suction side has pressure and velocity of 120 kPa and 1.5 m/s, respectively; the discharge side is 260 kPa and 3.2 m/s. Let γwater=9.81 kN/m3, g=9.81 m/s2 Round off your answer to four (4) decimal places.
Water with a velocity of 4.13 m/s flows through a 119 mm diameter pipe. Solve for the volume flow rate in m3/s. Express your answer in 3 decimal places.
From point A to point B of the system shown in the figure, oil flows (specific gravity of 8.64 kN/m3). A) Calculate the volumetric flow of the oil. ( WORK LIKE NEW PLEASE)
Derive an expression for the capillary rise h for a fluid of surface tension a and contact angle between two vertical plates a distance W apart, see figure below. What will be h for water at 20°C if W= 0.25mm?
1.) Water flows at 10m3/s in a 150-cm diameter pipe; the head loss in a 1000-m length of this pipe is 20.0m. Find the rate of energy loss due to pipe friction for the pipe. Use unit weight of Water : 9.79KN/m3.2.) Given the two dimensional flow as shown in the accompanying figure. Determine the flow rate considering 1.5m of width perpendicular to the figure.
Determine the flow of water in cubic centimeters. Asap 10 mins