3. Water enters an adiabatic steam turbine at 7 MPa and 450 °C at a flow rate of 100 m³/min and exits the turbine at 125 kPa. If the power output from the turbine is 25 MW, calculate the isentropic turbine efficiency and the exit volume flow rate. a) Isentropic turbine efficiency Answer: b) Exit volume flow rate (m³/sec) Answer:

3. Water enters an adiabatic steam turbine at 7 MPa and 450 °C at a flow rate of 100 m³/min and exits the turbine at 125 kPa. If the power output from the turbine is 25 MW, calculate the isentropic turbine efficiency and the exit volume flow rate. a) Isentropic turbine efficiency Answer: b) Exit volume flow rate (m³/sec) Answer:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a natural gas pipeline compressor, 110 m3/min. propane is compressed polytropically. The inlet pressure is 101 kPaa and the temperature is 38 0 The process follows pV1.08 = C. The exit pressure is 510 kPaa. Determine (a) the exit temperature, (b) the mass flow rate, (c) the heat loss, and (d) the work required.
In a natural gas pipe line compressor, 110 m^3/min of propane is compressed polytropically. The inlet pressure is 101 kPaa and the temperature is 38 degree C. The process follows pV^1.08 = C. The exit pressure is 510 kPaa. Determine (a) the exit temperature in kelvins, (b) the mass flow rate in kg/s, and (c) the heat loss in kW. And also draw the P-V and T-S diagrams.
Box the final answer. Write legibly. Steam flows into a turbine at a rate of 3.5 kg/s and ¾ MW of heat are lost from the turbine. Ignoring elevation and kinetic energy effects, calculate the power output from the turbine in KW? Steam pressure entering the turbine is 62 Bar at 440ºC and leaves at 74 Kpa.
Steam expands in a steam turbine steadily at a rate of 32,000 kg/h, that enters the turbineat 7 MPa and 600 oC (look to the Fig. 1); whereas, it leaves the turbine at 25 kPa as saturated vapor. Ifthis turbine generates a power of 6.5 MW at the ambient conditions of T0=27 oC, then,a) Write the mass balance of the fluid entering and leaving this turbine.b) Obtain the energy balance to determine the heat loss of the steam turbine,c) Find the entropy generation using the entropy balance and determine the destroyed exergy using thegenerated entropy,d) Find the exergy destruction using the exergy balance ,e) Find the maximum possible power output,f) Determine the second-law efficiency (ηII) of the steam turbine,
A reversible non-flow process occurs from which the work is 9.4 BTU. If the pressure varies as P = -V2 + 100/V, PSI (where V is in ft3), and P1 =46psi, determine P2 in psi.
Air from the discharge of a compressor enters a 1 m3 storage tank. The initial air pressure in the tank is 500kPa, and the temperature is 600 ⁰K. The tank cools, and the internal energy decreases by 213 kJ/kg. Determine the ff: a.) The Work done, b.) The heat Loss (unit in KJ), c.) The change in enthalpy, d.) The final Temperature.
A reversible non-flow process occurs from which the work is 9.4 BTU. If the pressure varies as P=−V*2+100/V, psi (where V is in ft3), and P1 = 46 psi, determine P2 in psi.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
Air enters the compressor of a gas-turbine engine at 300 K and 100 kPa, where it is compressed to 700 kPa and 580 K. Heat is transferred to air in the amount of 950 kJ/kg before it enters the turbine. For a turbine efficiency of 86 percent, determine: (a) the fraction of turbine work output used to drive the compressor, (b) the thermal efficiency.Assume: constant specific heats at 300 K.Ans: 50.1%, 29.6%
p90#11. ammonia vapor is compressed in a close system from 15 psia,3 cu ft to 150psia,0.4cu ft. according to the relation pV^n=constant. assuming the vapor to be an ideal gas with the gas constant as 90.72 lbm-ft/lbf-Degree rankine and Cv= 0.384 BTU/lbm-degree Rankine compute the heat transferred and the work.
3. Steam enters the turbine at the rate of 1.5 kg/s with enthalpy of 2300 kJ/kg and exhaust enthalpy of 1200 kJ/kg. Steam is extracted from the turbine at a rate of 0.87 kg/s for heating purposes with enthalpy of 2570 kJ/kg. What is the turbine work, in HP?
A boiler takes in feed water at 70 °C and generates steam at a pressure of 10 bar and drynessfraction 0.92. The wet steam enters a superheater and emerges with the same pressure at atemperature of 400 °C. If the steam flow rate is 5 tonnes per hour, determine (i) the rate atwhich heat transfer takes place in the boiler and (ii) the rate at which heat transfer takes placein the superheater. State any assumptions you have made in relation to the steady flowequation for the process.