3. What is the flux density of: a. chloride in a river whose average velocity is 10 cm/sec and whose chloride concentration is 220 mmol/liter? b. chloride across the freshwater-saltwater interface in an estuary, where the chloride concentration changes from 20 to 2 ppt (parts per thousand) in a distance of 5 m? c. n-octane vapor in a tank 4 m tall that is open at the top and contains a thin layer of liquid n-octane at the bottom? (Neglect any possible turbulence.

3. What is the flux density of: a. chloride in a river whose average velocity is 10 cm/sec and whose chloride concentration is 220 mmol/liter? b. chloride across the freshwater-saltwater interface in an estuary, where the chloride concentration changes from 20 to 2 ppt (parts per thousand) in a distance of 5 m? c. n-octane vapor in a tank 4 m tall that is open at the top and contains a thin layer of liquid n-octane at the bottom? (Neglect any possible turbulence.

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter14: Chromatography

Section: Chapter Questions

Problem 9P

See similar textbooks

Similar questions

Chemistry An aquifer contaminated with petroleum is found to have the following component concentrations at a particular site: benzene158 ppm toluene124 ppm ethylbenzene91 ppm xylene45 ppm n-heptadecane161 ppm pristane 84 ppm Provide an estimate for the age of the spill at this site using (a) BTEX ratio and (b) nC17:Pr ratio. Show your calculations and use units throughout. Give proper s.f. for the answer.
At 0°C and 1 bar, a monolayer of CO adsorbed on 1 g of Fe/Al2O3 catalyst occupies a volume of 4.25 cm3. What is the area of the catalyst? The area per adsorbed particle is 0.165 nm2. Give your answer in m2.
The thermal conductivities of human tissues vary greatly. Fat and skin have conductivities of about 0.20 W/m · K and 0.020 W/m · K respectively, while other tissues inside the body have conductivities of about 0.50 W/m · K. Assume that between the core region of the body and the skin surface lies a skin layer of 1.0 mm, fat layer of 0.50 cm, and 3.2 cm of other tissues. (a) Find the R-factor for each of these layers, and the equivalent R-factor for all layers taken together, retaining two digits. Rskin m2 · K/W Rfat m2 · K/W Rtissue m2 · K/W R m2 · K/W (b) Find the rate of energy loss when the core temperature is 37°C and the exterior temperature is 0°C. Assume that both a protective layer of clothing and an insulating layer of unmoving air are absent, and a body area of 2.0 m2. W
An aquifer contaminated with petroleum is found to have the following component concentrations at a particular site: benzene 158 ppm toluene 124 ppm ethylbenzene 91 ppm xylene 45 ppm n-heptadecane 161 ppm pristane 84 ppm Provide an estimate for the age of the spill at this site using (a) BTEX ratio and (b) nC17:Pr ratio. Show your calculations and use units throughout. Give proper s.f. for the answer.
A sample of steel (0.506 g) was digested in acid and the solution made up to 100 cm3 with deionised water. Aliquots (25.0 cm3) of this solution were transferred into two volumetric flasks (100 cm3) labelled A and B. Flask A was made up to volume with deionised water. To flask B was added 10.0 cm3 of a 260 ppm standard solution of Mn2+ which was then also made up to volume with deionised water. The following absorbance results were obtained: Solution A = 0.356, Solution B = 0.578. Use these results to calculate the percentage (% w/w) of manganese in the steel sample.
A particular liquid crystalline substance has the phasediagram shown in the figure. By analogy with the phasediagram for a nonliquid crystalline substance, identify thephase present in each area.
40. Which of the following affects the sedimentation of a particle in gradient ultracentrifugation? Group of answer choices the affinity of the particle for the gradient solution the viscosity of the particle solution the total mass of the gradient and tube the density of the gradient solution the number of hydrophobic residues
Microstructure of a steel contain 100% coarse pearlite it carbon content is reported to be 0.65% is it possible? And why ?
0.5M HA electrolyte with a degree of dissociation of 0.2; It is placed in a conductivity cell with a length of 0.9 cm and an area of 2cm2 and its conductivity is read as 300 mS. According to these data; a) Equivalent conductivity of the electrolyte b) Boundary equivalent conductivity c) Decomposition constant
10 Find the transition time of 20g naphthalene with the surrounding temperature as 30oC.Let the boiling tube has mass 25 g, diameter 2.5 cm and thickness 0.15cm. How much time does 30g of ice takes to melt at a surrounding temperature of -50C. (We are using a boiling tube having mass= 20g, radius=1.5cm, thickness=0.2cm.) In the above experiment, let the surrounding temperature is changed to 0oC. What will be the change in the transition time for ice? Repeat the experiment for different surrounding temperatures and study the variation of melting point of ice. Calculate the melting point of wax having a mass 30g. Let we are using a boiling tube of mass 25g, having a thickness 0.5 cm and radius 1.5 cm.( Choose surrounding temperature as 40oC)
Consider liquid n - hexane in a 50 - mm - diameter graduated cylinder. The distance from the liquid - gas interface to the top of the cylinder is 20 cm. The steady - state n - hexane evaporation rate is 8.2.10-4 kg / s and the n - hexane mass fraction at the liquid - air interface is 0.482. The diffusivity of n - hexane in air is 8.0. 10 ^ m / s. A. Determine the mass flux of n - hexane vapor. Give units. B. Determine the bulk flux of n - hexane vapor, i.e. , that portion associ ated with the bulk flow, at the liquid - gas interface. C. Determine the diffusional flux of n - hexane vapor at the liquid - gas interface.
An amino acid moves randomly through water with steps of about 3 angstroms (3 x 10^-8 cm) in length at a rate of 1 x 10^10 steps per second. This substance is passing through a reverse phase HPLC column which has a plate height of 0.010 cm. 1. Estimate the diffusion coefficient for the amino acid in water. 2. Calculate the width at the base of the elution zone after the amino acid has migrated 50 cm through the column