Please answer all subpart either dislike is readyPlease Asap for like 3.08V1VtAverage Output Voltage [V]Output Voltage ripple [%]Find the following for a 60Hz AC sourceSub-questionVt: Voltage magnitude on transformer secondary [V]R1 average load current [A]D1Diode average forward current [A]Diode repetitive peak current (steady state) [A]Diode inrush surge current [A]D1 peak reverse voltage [V]VoutC1R1ParameterSupply AC Voltage [V]D1 on voltage [V]T1 turns ratio [Np/Ns]C1 Capacitance [F]R1 Resistance [0]Value10110.160.0001151300

Since you have asked multiple questions in a single request, we will be answering only the first…

3.08 V1 Vt Output Voltage ripple [%] D1 + Find the following for a 60Hz AC source Sub-question Vt: Voltage magnitude on transformer secondary [V] Average Output Voltage [V] Vout C1 R1 Parameter Supply AC Voltage [V] D1 on voltage [V] T1 turns ratio [Np/Ns] C1 Capacitance [F] R1 Resistance [0] Value 101 1 0.16 0.0001 1300

3.08 V1 Vt Output Voltage ripple [%] D1 + Find the following for a 60Hz AC source Sub-question Vt: Voltage magnitude on transformer secondary [V] Average Output Voltage [V] Vout C1 R1 Parameter Supply AC Voltage [V] D1 on voltage [V] T1 turns ratio [Np/Ns] C1 Capacitance [F] R1 Resistance [0] Value 101 1 0.16 0.0001 1300

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and current relationships change? (a) If C1 is the complex positive-sequence voltage gain in Problem 3.29 and (b) if C2 is the negative sequence complex voltage gain, express the relationship between C1andC2
What is CEMF?
For a Full wave rectifier circuit, the AC voltage input to transformer primary is 115V. Transformer secondary voltage is 50V. Load resistor is 25 ohms. Determine Peak and Average DC Component of load voltage. (Assume ideal diodes) a.VDC (peak) = 25.4 V; VDC (average) = 18.5V b.VDC (peak) = 35.4 V; VDC (average) = 22.5V c.VDC (peak) = 38.4 V; VDC (average) = 23.5V d.VDC (peak) = 50 V; VDC (average) = 34.5V
A single-phase center-tapped transformer rectifier has an ac source of 240 V rms and 60 Hz. The overall transformer turns ratio is 3:1 (80 V between the extreme ends of the secondary and 40 V on each tap). The load is a resistance of 462 Ω. Determine (a) the average load current, (b) the rms load current, (c) the average source current, and (d) the rms source current. Sketch the current waveforms of the load and the source
Q ) For the full- wave uncontrolled rectifier circuit supplying a series resistive Thesupply voltage is v =300 sinωt , the supply frequency is 50 Hz and the loadparameter values are: R =05 Ω,a) Sketch the diagram of electrical circuitb) Sketch the load voltage and current waveforms .c) Calculate the load currentd) Calculate the average DC load voltage Vdc .e) Calculate the supply power to the loa
What is the maximum value of vs(i.e.vsm ) Find the peak-to-peak ripple voltage vr Find the average output voltage Vo in steady state Find the average diode current ID in steady state. If the secondary winding resistance of the transformer is 1.5 Ω, calculate the maximum surge current in the worst-case scenario
Which of the following statements about bridge tip rectifiers is false? A) If the 1-phase type has source inductance, the average value of the output voltage is lower than in the absence of the inductance. B) The average output voltage value of the 1-phase type is 0.9 times the peak voltage of the network. C) none D) There are only odd harmonics in the current drawn by the 1-phase type from the mains. E) The average value of the output voltage of the 3-phase type is larger as the 3-phase and 1-phase types are compared
Given: Half-wave rectifier; transformer secondary voltage = 32 V; Capacitance 4700 μF; average load voltage 18 V. Determine ripple factor and average load current. Show complete solution.
write down the formulae for 3-phase fully controlled,full wave rectifier with inductive load for the following parameters: Average DC voltagerms voltagepeak inverse voltagerms currentaverage DC currentefficiencyfiring angleextinction anglepower outputpower inputform factorripple factordistortion factortotal harmonic distortiondisplacement factorpower factor of rectifier. Please answer all subpart...
Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si
The secondary input voltage to a single phase diode bridge rectifier is 50V, 50Hz, and the load can be replaced by a resistance of value 20ohms (a) Sketch a well labelled circuit of the converter described above. (b) Sketch the waveforms for the input voltage, output voltage, output current, and output current (c) Derive an equation for average output voltage and calculate for output dc voltage (d) Calculate the ripple factor of the output voltage (e) Transformer utilization factor (h) How can the ripple be improved
The turn-ratio of the transformer ( N1 / N2 ) = ? / The PIV rating for diodes , PIV = ? / The Average diode Current IDavg = ?