Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si

Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.9P

See similar textbooks

Related questions

Q: A Capacitor filter is used at the output across the load in order to minimize the ripple factor of…

Q: Given that RI = i0, R2 (Rload) - IKA, LI - 750mH, k - 1,Vi - 220V.f = 60HZ, assume an ideal diode,…

A: A center tapped full wave rectifier is given. It converts AC into pulsating DC.

Q: (b) If such a circuit is to be used to supply an average of 10 V across the load, calculate the…

A: Full-wave rectifier: This rectifier converts the AC into the DC. If it contains the split winding on…

Q: Q1-Determine the ripple factor (r) for the filtered rectifier with a load as indicated in the figure…

A: Rectifier: It converts AC power to DC power whose average output voltage and currents are finite.…

Q: How is the diode and zener diode in the electronic circuit and how they work? indicate the…

A: Given : Note : It is the kind notice that according to the guidelines of the company whenever we…

Q: sentences: 8) The primary mmf is not equal and same direction to the secondary mmf in an ideal…

A: The question is about characteristics of Ideal transformer.

Q: In the full-wave rectifier circuit of figure , the transformer has a turns ratio of 1:2. The…

A: We need to calculate peak to peak ripple voltage for full wave rectifier .

Q: For the cct shown: 1-Determine the voltage available from the voltage doubler shown if the secondary…

Q: A step-down delta-star transformer, with per-phase turns ration of 5, is fed from a 3-phase, 1100 V,…

A: The solution can be achieved as follows.

Q: Example 1. For the half-wave rectifier shown below, determine the following: (a) Secondary voltage…

A: As per the guidelines of Bartleby we supposed to answer first three subparts of the question for…

Q: 1- An eight stage Cockcroft-Walton circuit has all capacitors of 0.05 F. The secondary voltage of…

A: Given:No. of stages=8C=0.05 μFf=150 HzVm=120 kVIL=1 mA

Q: - Work on the two Sub parts of the problem electonica below using the explanation steps from the…

A: Current Transformer 1) It is used to measure High current. 2) It is connected in series with the…

Q: b) A single-phase diode bridge rectifier has a purely resistive load of R-15 2 and, VS-300 sin 314 t…

A: given here a single phase bridge rectifier has a purely resistive load of R = 15 Ω and Vs = 300 sin…

Q: A single phase Full-wave controlled rectifier is connected to center- tapped transformer that…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: If the input voltage for the given circuit below is 220 V at 60 Hz the load resistance (RL) is 5600n…

A: To charge battery from AC supply rectifier (converter) circuits are used. According to supply a…

Q: For a half-wave rectifier filter, Determine: The capacitance value required to limit the…

A: Given Vr(pp) =3V f=60 Hz IFL =IDC =3 A Load resistance (RL) and Average output voltage (Edc) are not…

Q: (a) What value of filter capacitor is required to produce a 1% ripple factor for a full-wave…

A: For the given Full wave rectifier having RL = 1.5 K ohms V ripple = 1% of V peak V peak = 18 V…

Q: A Cockcroft-Walton type voltage multiplier has ten stages with capacitances, all equal to 0.1 µF.…

A: For the Cockcroft-Walton type voltage multiplier which has 10 stages, the percentage ripple,…

Q: In the figure given we have u(t)=10- cosot [V]. We assume the diodes and the A-meter (A) to be…

Q: Q1. Describe the following related to Current Transformer (CT): Draw the equivalent circuit diagram…

A: Equivalent circuit diagram of CT in which, n=turns ratiors=resistance of 2° windingxs=reactance of…

Q: A full wave rectifier circuit is fed from center tap transformer. The RMS voltage from the end of…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: an ideal transformer circuit is shown in Figure Q4(a). Its primary and secondary turns are 400 and…

Q: A single-phase transformer with secondary voltage of 230 V, 50 Hz, delivers power to a resistive…

A: For half wave controlled rectifier, the expression for the output voltage is given as:

Q: A resistive heater is energized from 220Vrms, 50 Hz sinusoidal voltage source through a ransformer…

Q: If the rectifier in figure has a purely resistive load of R, determine (a) ripple factor, (b)…

A: Ripple factor- It is define as the ratio of ripple voltage to the average output voltage. Ripple…

Q: (a) Derive the equivalent circuit model (transformer model) include only the inductor loss (RL) and…

A: The given circuit diagram is shown below,

Q: Q1-Determine the ripple factor (r) for the filtered rectifier with a load as indicated in the figure…

A: DIODE: A diode is a semiconductor device that functions as a current one-way switch. It lets current…

Q: Q5. For the following center tapped transformer, show the wave form across each half of he secondary…

A: As per Bartleby policy we can answer only one question at a time, please repost it for other parts.…

Q: Q-2 A Cockcroft-Walton type voltage multiplier has Seven stages with capacitances, all equal to 0.3…

Q: Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Design a Bridge FWR to supply a load of (100) with the waveform shown in figure from the main power…

Q: In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2. The…

A: In this question we need to find a peak to peak output voltage of the given rectifier.

Q: 4. In the following circuit, the transformer's secondary has a peak voltage of 8V, sketch waveform…

A: Fig: Given circuit Case 1: For positive half cycle of the AC input…

Q: Design a Bridge FWR to supply a load of (1000) with the waveform shown in figure from the main power…

A: As you are not mentioning which question you want . we will solve first question for you. Full Wave…

Q: The primary winding to secondary winding turns ratio of a centre-tapped transformer is 5:1. The…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2 The…

A: In this question, We need to choose the correct options What is peak to peak ripple voltage?

Q: FN.Q5 – A Transformer has primary windings as Np = 720 and secondary windings as Ns = 144. Its…

A: Given, the secondary Voltage V2= 42 V Rated output power = 2750 W The load Resistances RL1 = 1.66…

Q: Q4. For the three-phase fully-controlled bridge rectifier circuit shown with purely resistive load:…

A: It is given that:

Q: The rated power of a certain transformer is 1 kVA. The transformer operates at 60 Hz and 120 V ac.…

A: The solution is given below

Q: (i) A chopper circuit drives an inductive load from 120 DC supply. Given the load resistance as 6 0,…

A: Input to chopper circuit = 120 V DC. Output average current = 52.5 Amp Output resistance /load…

Q: Q5. For the following center tapped transformer, show the waveform across each half of the secondary…

A: Consider the circuit given in the figure: When we treat transformer with input terminal A as…

Q: Q: A single phase Full-wave controlled rectifier is connected to center- tapped transformer that…

A: Dear student as per our guidelines we are supposed to solve only one question in which it should…

Q: Q5. For the following center tapped transformer, show the waveform across each half of the secondary…

A: An device which convert alternating signal in to pulsating direct signal. The half wave rectifier…

Q: A three-phase uncontrolled bridge rectifier delivers power to a resistive load of 102. The output…

A: The rating of source side of three phase star-delta transformer=PdT.U.F.…

Q: Given: Half-wave rectifier; transformer secondary voltage = 32 V; Capacitance 4700 μF; average load…

A: Given:Vs=32VC=4700μFVdc=18V

Q: For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 10.2-0-10.2 V…

A: PIV rating of the diode referes to value of the voltage that appears across the diode terminal when…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode).

Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
What is the maximum value of vs(i.e.vsm ) Find the peak-to-peak ripple voltage vr Find the average output voltage Vo in steady state Find the average diode current ID in steady state. If the secondary winding resistance of the transformer is 1.5 Ω, calculate the maximum surge current in the worst-case scenario
Industrial Electronics Please give the step-by-step solution of the following:(a) Standard average current diode rating (b) Standard peak current diode rating (c) Transformer
A single-phase center-tapped transformer rectifier has an ac source of 240 V rms and 60 Hz. The overall transformer turns ratio is 3:1 (80 V between the extreme ends of the secondary and 40 V on each tap). The load is a resistance of 462 Ω. Determine (a) the average load current, (b) the rms load current, (c) the average source current, and (d) the rms source current. Sketch the current waveforms of the load and the source
For the below given circuit, a step-down transformer is used with a root mean square voltage equal VRMS = 230/20 The input frequency is 60 Hertz, RL= 4.2 kΩ, all diodes used are silicon diodes. 1) Find a) The peak Input voltage Vpin (in volts): Answer for part 1 b) The peak output voltage Vpout (in volts): Answer for part 2 c) The Average output voltage Vavg (in volts): Answer for part 3 d) The current across the load resistance( in milliampere): Answer for part 4 e) The Ripple Frequency(in Hertz): Answer for part 5 f) Draw the Input and output waveform g) Name the above given circuit.
Single phase transformer with voltage : 220/15 V, used as half wave rectifier, with silicon diode in ideal condition, Load RL = 20 Ω Calculate : VDC, lDC solve with the step thank u
A Cockcroft-Walton type voltage multiplier has ten stages with capacitances, all equal to 0.1 μF. The supply transformer secondary voltage is 100 kV at a frequency of 60 Hz. If the load current to be supplied is 5 mA, find (a) the percentage ripple, (b) the regulation, and (c) the optimum number of stages for minimum regulation or voltage drop.
I need to power a 15kw/20HP DC Motor with a rectified 24VDC from a step down transformer with input of 11A and output of 103A/12VAC -24VAC. What is the required Capacitance needed to ensure ripples are cleared and also gives a steady VDC of 24VDC to the DC Motor to run quite well. Please, all note that the rectifier is a full wave rectifier of 100A...
Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter connected with D1 indicates 8 A r.m.s current, and the source frequency is 50 Hz Due to system inductance the average voltage drops to 96.2% of idealized value ( when the inductance is neglected). How much will the average and r.m.s voltage s be? The r.m.s phase current and average load current Is=? & Idc=? The secondary r.m.s voltage and transformer capacity Vs & KVA? The inductances causes the voltage drop Lc=? The diode forward current and maximum inverse voltage? Now, if the phase B is failed ( disconnected), how much with new dc voltage be in %..Vdc=….% ??
A FW rectifier is required to deliver 48VDA with 10% ripple on a 7.5Ω resistor. a)Identify the capacitor providing these values (capacitance and ripple current - ripple current). b)Identify the necessary welding transformer for 120VAA 60Hz welding.c) Find the required serial inductance value for continuous current withdrawal from the source
Design a bridge-type full-wave rectifier fed from the 240-V line through a step-down transformer. The load requires an average voltage of 14 V and average power of 6 W.
Given: Half-wave rectifier; transformer secondary voltage = 32 V; Capacitance 4700 μF; average load voltage 18 V. Determine ripple factor and average load current. Show complete solution.