30 KN/m A B 3.00 m 6.00m H 5 Panels@4.00 m = 15.00 meters PROBLEM NUMBER 1: In the given cantilever platform carrying a uniform distributed load (note: distribute the loads at joints A,B,C,and D). Determine the magnitude and type for the bar forces in .Place your answers here. Magnitude, KN members DE,EJ and JK. Member DE EJ Type of Force JK

30 KN/m A B 3.00 m 6.00m H 5 Panels@4.00 m = 15.00 meters PROBLEM NUMBER 1: In the given cantilever platform carrying a uniform distributed load (note: distribute the loads at joints A,B,C,and D). Determine the magnitude and type for the bar forces in .Place your answers here. Magnitude, KN members DE,EJ and JK. Member DE EJ Type of Force JK

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

13. A tank of water (SG = 1) has a gate in its vertical wall 5 m high and 3 m wide. The top edge of the gate is 2 m below the surface. What is the hydrostatic force on the gate?a. 147 kNb. 367 kNc. 490 kNd. 661 kN
QUESTION-1: Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
(c) Figure Q2(c) shows a homogenous 1.2 m wide and 3 m long rectangular gate is held in place by a horizontal flexible cable. Water acts against the gate, which is hinged at point A. Calculate the magnitude, FR and location of the resultant force, yR.
Replace the loading (Figure 1) by an equivalent resultant force and couple moment at point O. Suppose that F1={8i−2k}kN and F2={−4i+5j−2k}kN. Part A Part complete Determine the resultant force. Enter the x, y, and z components of the force in kilonewtons to three significant figures separated by commas. Part B Determine the equivalent resultant couple moment about point O. Enter the x, y, and z components of the moment in kilonewton-meters to three significant figures separated by commas.
The maximum number of ways to solve a structure with single degree of indeterminacy using MCD (Force Method) is: a. 1 b. 2 c. 3 d. 4 e. 5
Construct the shear -force diagram and identify the largest negative shear force. Assume a = 3.1 ft, b = 6.2 ft, c= 12.4 ft, W= 1200 1b/ft. and Pa 1200 1b,
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ,compression bars As’ = 2-28 mmØ, d’ = 60 mm. Fc’ = 30 MPa and fy = 345 MPa Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN Please answer asap.
ASAP PLEASE. 4 DECIMALS THANK YOUUU What is the value of R1 in kN? What is the value of R2 in kN? Locate the point of zero shear from point A in meters. What is the Maximum Positive Shear Force in kN? What is the Maximum Negative Shear Force in kN? What is the Bending Moment (in kN-m) at the point of zero shear? What is the Maximum Negative Bending Moment in kN-m? What is the shear force (in kN) located 9 meters from point A? What is the bending moment (in kN-m) located 9 meters from point A? What is the slope of the the shear force on segment EF?
The bent bar shown is subjected to 3 forces shown. Replace these forces with an equivalent couple M and single force F at point A. Show solution to answers M = 21.8 kN-m, cw Fv = 12.03 kN, D FH = 1.60 kN, R
Determine the x and y components of F1 and F2 acting on the boomshown . Express each force as a Cartesian vector.
A building's entrance canopy is constructed as a fixed slab attached to one of its longer sides. The slab has dimensions of 2.50 m x 6 m and a thickness of 225 mm. It is designed to bear various loads, including a uniform live load of 2000 Pa, a uniform dead load of 5000 Pa (excluding the weight of the slab itself), and a concentrated dead load of 5000 N per meter applied at the far end of the support. The design of the slab ensures that the main bars are oriented parallel to the shorter span. The specified design properties include a compressive strength (fc') of 21 MPa, a yield strength (fy) of 345 MPa, 16-mm-diameter main bars, 10-mm-diameter temperature bars, and a clear cover of 20 mm. The unit weight of the concrete is 23,544 N/m3.Find: 1. Determine the spacing of the main bars in mm 2. Determine the spacing of the temperature bars in mm
Find the total force on the side of a water-filled cylindrical tank with 5m height and 10m diameter woter =9800 N/m' a) 3848 KN b) 5547 KN Ocd 7696 KN d) 2770 KN