only HANDWRITTEN answer needed ( NOT TYPED) 30 mm600 mmB36 mmT= 500 Nm900 mmJABVTwo solid steel shafts are fitted with flanges that are thenconnected by bolts as shown. The bolts are slightlyundersized and permit a 1.5° rotation of one flange withrespect to the other before the flanges begin to rotate as asingle unit. Knowing that G = 77.2 GPa, determine themaximum shearing stress in each shaft when a torque of Tof magnitude 500 Nm is applied to the flange indicated.The torque T is applied to flange C.(AB=0.6m14ABT= TAB2T1C = √2/2d²0000000295=

The rotation of the flange with respect to other flange is φb=1.5°=0.02618 rad. The applied torque…

Answered: 30 mm 600 mm 36 mm T = 500 N-m с 900 mm…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hollow steel (G = 12,000 ksi) shaft has diameters of 6 in. and 4 in. and an allowable shearing stress of 9,000 psi. Determine the required number of 3⁄4-in diameter bolts for a flange coupling in which two-thirds of the bolts are on a 12-in diameter bolt circle and one-third are on a 9-in diameter circle. The allowable shearing stress in the bolts is 12,000 psi.
A flange coupling is to be designed, using 6 bolts at a distance of 89 mm from the center of the shaft, allowable shearing stress on the bolt is 103 MPa. If the shaft is to transmit 4035hp at a speed of 1200 rpm, (a) determine the bolt diameter required in mm. (b) If the shaft is made of the same material as the bolt, determine the required diameter of the shaft in mm.
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
The solid rod AB has a diameter dAB5 60 mm and is made of a steel for which the allowable shearing stress is 85 MPa. The pipe CD, which has an outer diameter of 90 mm and a wall thickness of 6 mm, is made of an aluminum for which the allowable shearing stress is 54 MPa. Determine the largest torque T that can be applied at A
A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: The required diameter doof the solid shaft.g The required outer diameter d2of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. 3.The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
A flange coupling is to be designed, using 6 bolts at a distance of 149mm from thecenter of the shaft, allowable shearing stress on the bolt is 103 MPa. If the shaft is totransmit 5485 hp at a speed of 1200 rpm, (a) determine the bolt diameter required inmm. (b) If the shaft is made of the same material as the bolt, determine the requireddiameter of the shaft in mm.
A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: The required diameter do of the solid shaft. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts. 1
A flywheel is to be fitted on a punching machine with 73% mechanical efficiency. The machine makes 20 working strokes per minute. The holes are 20-mm diameter, thickness of 12 mm steel plates with an ultimate shear strength of 330 MPa. The punching operation takes place during 1/9th of a revolution of the crankshaft. Determine the capacity (kW) of a driving motor necessary to operate a punching machine.
A 1.5 inch diameter solid shaft is made of Aluminum 2014-T6, if the maximum allowable shear stress is 25ksi and the factor of safety is 3, and the torques across the length of the shaft are T/3, -T, 2T/3 and the distances between the torques are 12 inches, and the angle of twist is limited so that it does not exceed 0.1 rads. Determine the maximum allowable torque T in the shaft.
A composite shaft shown, composed of a steel (G = 77 GPa) core inside an aluminum (G = 25 GPa) jacket, carries a torque, T = 10 kN-m. The shaft is designed such that the aluminum jacket will fail first upon the application of the torque. 1) If the allowable shear strength of aluminum is 45 MPa, determine the minimum thickness, t, of the aluminum jacket, that can carry the torque.2) What must be the minimum shear strength of steel such that the aluminum jacket will fail first?3) Determine the maximum angle of twist that can be applied to the shaft.
A steel shaft must transmit 150 kW at a speed of 360 rpm. Knowing that G = 77.2 GPa, design a solid shaft so that the maximum shearing stress will not exceed 50 MPa and the angle of twist in a 2.8-m length must not exceed 3°. Consider the frequency f to be 6 Hz. The diameter of the solid shaft is -- mm
A flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and 8-12mm diameter on a concentric bolt circle 260mm in diameter. What torque can be applied without exceeding a shearing stress of 60MPa in the bolts? B) Determine the number of 10mm steel bolts that must be used on the 320mm bolt circle of the coupling to increase the torque capacity by 6KN-m.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS