30312 kj / h heat is given to the milk flowing with a mass flow rate of 40 kg / min in the plate heat exchanger and the milk leaves the heat exchanger at 96. The specific heat of milk is 3.86 kj / kg. Accordingly, calculate the milk inlet temperature to the heat exchanger. A.) 25 ℃ B.) 100.73 ℃ C.) 15 ° C D.) 17.17 ℃ E.) 91.27 ℃

30312 kj / h heat is given to the milk flowing with a mass flow rate of 40 kg / min in the plate heat exchanger and the milk leaves the heat exchanger at 96. The specific heat of milk is 3.86 kj / kg. Accordingly, calculate the milk inlet temperature to the heat exchanger. A.) 25 ℃ B.) 100.73 ℃ C.) 15 ° C D.) 17.17 ℃ E.) 91.27 ℃

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.1DP

See similar textbooks

Similar questions

The data provided by a water bottling company for the year 2020 to carry out Break Even Analysis and provide them the results, is as follows. The fixed cost of the year is 9000.0 R.O The estimated sales are 2200000 units The cost of water treatment / unit 12 baize The cost of bottling / unit 08 baize The cost of labelling / unit 08 baize The cost packing / unit 10 baize The cost of labour and maintenance / unit 20 baize The cost of 1 liter bottle (plastic bottle) 12 baize Each unit is sold at price 95 baize Construct the B.E.P chart on a graph sheet and indicate M.o.S, B.E.P and also indicate the new B.E.P, & M.o.S after the improvement measures has been taken and show all mathematical calculations. 1. Determine the B.E.P 2. Determine the profit 3. Margin of safety. 4. Write your decisions to improve the profits of the company and to reduce the B.E.P
Instruction: Show your solution. (Engineering Utilities 2) Problem: A compressor draws in 500 cubic feet per minute of air whose density is 0.079 pounds per cubic feet and discharges it with a density of 0.304 pounds per cubic feet. At the suction, pressure # 1 = 15 pounds per square inches and at the discharge, pressure # 2 = 80 pounds per square inches. The increase in internal energy is 33.8 Btu per pound of air, and the heat rejected from air by cooling is 13 Btu per pound of air. Determine the work done on the air in Btu per minute and in horsepower. (1Btu = 778.16 ft-lbf; 1hp = 42.4 Btu/min)
Need a cancellation method. Thermodynamics
Specific fuel consumption of a four-stroke internal combustion engine at a given rotational speed is 0.322 kg/kW-h value is minimum. Spindle power at this rotation rate is 123 kW, volumetric efficiency is 95% and air-fuel rate is 15. The number of rotations of this engine is calculated by subtracting 1.5 from the number of rotations giving the minimum specific fuel consumption. time, spindle power 162 kW, specific fuel consumption 0.394 kg/kW-h and volumetric efficiency 85%. a) Calculate the air-fuel ratio in this case. and By what percent has the efficiency of the engine changed?
Please provide equations that you are using so I can follow along and learn how to do this. In Jamestown, NY, a coal power plan consumes coal at a rate of 80 tons/hr. When coal burns, it generates approximately 30,000 kJ for every kg of coal burned. The cooling course for the plant is the nearby Chadakoin River nearby and, by code, the power plant cannot reject more than 13.19 x 109 MJ into the river annually. Determine the maximum average power output of this plant and it's maximum thermal efficiency. To check your work, enter the efficiency, as a decimal, in the box provided.
solve a,b, c and d please. In a detergent-making process, 1400gal/h of water ﬂows through a 2-inch pipe system as follows: Exit from pump, 2ft vertical, open gate valve, 14 ft vertical, 908 bend, 12ft horizontal, 1/4 open globe valve, 20ft horizontal, 908 bend, 6ft horizontal, 908 bend, 12ft vertical, 908 bend, 14ft horizontal, 908 bend, 4 ft vertical, 908 bend, 28ft horizontal, open gate valve, 3ft horizontal, entry to tank containing 30ft of liquid. (a). If the pump and tank are both at grade level, estimate the head that the pump must deliver. (b). If the pump inlet pressure is 25 psig, what is the outlet pressure? (c). Estimate the pump shaft work ( d). If the pump is powered by an electric motor with 85% efﬁciency, what is the annual electricity consumption?
Course: Power Plant Question: 5 In some application V-8 four stroke petrol engine is needed to produce 190 kW at 4420 rpm. At the given engine speed the air-fuel ratio (A/F) is 15/1 and the volumetric efficiency is 70 percent. Also at the compression ratio of 10/1, the brake thermal efficiency is considered to be 35%. The calorific value of the fuel used is 44200 kJ/kg and the free air conditions are 1 bar and 15 0C. The bore to stroke ratio (B/S) is 0.8 for the engine. Solve the problem to find the following: a. Engine displacement b. Size of the bore c. Size of the stroke
thermodynamics cycle
step-by-step process
Dusty air at a fertilizer plant flows through a 13% efficient cyclone and then through an ESP, The inlet air to the cyclone has a dust loading of 80 grains/cubic foot. In order to meet a standard of 98,5% collection efficiency for the fertilizer plant as a whole, what is the allowable concentration of dust (in grains/cubie foot) in the air that exits from the ESP?a. 0.15 gr/ft3 b 1.2 gr/ft3c. 21.6 gr/ft3 d. 58.4 gr/ft3
One of the assumptions is not used in derivation of Bernoulli's equation? frictionless flow transient control volume constant fluid density none adiabatic control volume
A liquid-to-gas counterflow heat exchanger is used to cool gas from 32°C to 18°C. Assuming that the liquid enters at 7°C and leaves at 15°C, calculate the log mean temperature difference in °C. Draw and label the temperature-flow diagram. Round off your answer to three (3) decimal places.