3-17: A part for a truck suspension system is to carry a compressive load of 135 kN with the possibility of shock loading. Malleable iron ASTM A220 grade 45008 is to be used. The cross section is to be rectangular with the long dimension twice the short dimension. Specify suitable dimensions for the part

3-17: A part for a truck suspension system is to carry a compressive load of 135 kN with the possibility of shock loading. Malleable iron ASTM A220 grade 45008 is to be used. The cross section is to be rectangular with the long dimension twice the short dimension. Specify suitable dimensions for the part

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.5P: An inflatable structure used by a traveling circus has the shape of a half-circular cylinder with...

See similar textbooks

Similar questions

A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in. passes through each davit and supports two pulleys. are on each side of the davit. Cables attached to the lifeboat pass over the pulleys and wind around winches that raise and lower the lifeboat. The lower parts of the cables are vertical and the upper parts make an angle a =15° with the horizontal. The allowable tensile force in each cable is 1800 lb, and the allowable shear stress in the pins is 4000 psi. If the lifeboat weighs 1500 lb, what is the maximum weight that can be carried in the lifeboat?
The force P3 to make it to equilibrium in kN is The Stress in section 1 in N/mm2 is The Compressive Stress in section 2 in N/mm2 is The stress in section 3 in N/mm2 is The total change in length in x10-3 mm is
8. Design a clamp coupling for transmitting 25 kW at 300 rpm. Allowable shear stresses in shaft and key are 50 MPa and 45 MPa, respectively. The number of bolts joining the two halves of muff is 4. The permissible tensile stress in the bolt is 70 MPa and the permissible crushing stress in the key is 90 MPa. The coeffi cient of friction between the muff of the CI and the shaft of steel is 0.20.
Find the Axial Forces in members 1 - 5. Find the Displacement Displacement of joint A (mm, positive right and up) for both Horizontal and Vertical
For the same question, the M25 Screw will be used when pressing the Nut Wheel onto the shaft. Assuming that the force that the nut needs to suppress is Fçak=1218 kgf (it was found in the previous question, but we don't use it), what should the minimum NUT HEIGHT be in mm to create this force safely? (Screw and Nut's surface safety pressure Pem=45 N/mm2 Screw base diameter d1= 21.5 mm. (Calculate the pitch (h=?) according to the given ones, considering that metric screw is used!)
The figure below is a schematic drawing of a shaft that supports two V-belt pulleys. The loose belt tension on the pulley at A is 15% of the tension on the tight side. The shaft material has a yield strength of 300 MPa and an ultimate tensile strength of 520 MPa. Calculate the shaft diameter.
O: A shaft is to be designed for a linkage of a windshield wiper mechanism for a truck as shown in Tigure below. A 20-N force is applied to lever 1 (I'1) by an adjacent link. The reaction force (F2) on lever 2 is transmitted to another link. Requirement: Select suitable bearings points A & D.
3. Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the shaft and key is 40 MPa and the number of bolts connecting the two halves are 4. The permissible tensile stress for the bolts material is 70 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3.
Solve the effective normal force on the rod CD Use units [N,mm] The mass of the load is: mk=21904 kg
A leafs spring contains 4 full-length and 8 graduated leafs. The eyebolts at the support are 20 inches apart and the system should carry a load of 400 lbs. If the thickness of the available bronze plate is 1“ and Sy = 80 ksi, what leaf width is required at FOS = 8?
For the helical compressive spring under fatigue load must meet
The shaft, is driven by pulley B from an electric motor. Another belt drivefrom pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratioof belt tensions for pulley B is 3.5. The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensilestress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion andbending factors as 1.25 and 1.75 respectively, find the shaft diameter.Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare theweights of the two shafts. [Ans. 30 mm ; 24 mm ; 1.82 Given Length CD=350mm Length AB=150mm Length BD=100mm The total length is CD =350