36 - By applying a sinusoidal signal of frequency w0 to a linear system, the steady-state output of the system will be: O A) a sinusoidal signal with the same phase, but difference in amplitude and frequency O B) a sinusoidal signal with the same frequency, but difference in amplitude and phase O C) a sinusoidal signal with the same amplitude, but difference in frequency and phase O D) any signal with the difference frequency and amplitude O E) any signal with the same frequency and amplitude

36 - By applying a sinusoidal signal of frequency w0 to a linear system, the steady-state output of the system will be: O A) a sinusoidal signal with the same phase, but difference in amplitude and frequency O B) a sinusoidal signal with the same frequency, but difference in amplitude and phase O C) a sinusoidal signal with the same amplitude, but difference in frequency and phase O D) any signal with the difference frequency and amplitude O E) any signal with the same frequency and amplitude

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.27P: An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8...

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Give the solution for J and K ONLY ans (0.99959 degrees and 63.643 ms respectively).Read A 70-Vac source has the following waveform. Determine:a. Vpkb. Vpk-pkc. Vrmsd. Periode. Frequencyf. Angular Velocityg. Phase Angleh. equation of the waveform (in time domain)i. the instantaneous voltage when t = 120 msj. the angle (1st occurrence) after t = 0 when the voltage is +80 Vk. the time (2nd occurrence) after t = 0 when the voltage is –10 VAnswers:a. 98.9949 Vb. 197.9899 Vc. 70 Vd. 100 mse. 10 Hzf. 20π rad/secg. 125.0876°h. v(t) = 98.9949sin(20πt + 125.0876°)i. -29.0880 Vj. 0.99959°k. 63.643 ms
Read A 70-Vac source has the following waveform. Determine:a. Vpkb. Vpk-pkc. Vrmsd. Periode. Frequencyf. Angular Velocityg. Phase Angleh. equation of the waveform (in time domain)i. the instantaneous voltage when t = 120 msj. the angle (1st occurrence) after t = 0 when the voltage is +80 Vk. the time (2nd occurrence) after t = 0 when the voltage is –10 VAnswers:a. 98.9949 Vb. 197.9899 Vc. 70 Vd. 100 mse. 10 Hzf. 20π rad/secg. 125.0876°h. v(t) = 98.9949sin(20πt + 125.0876°)i. -29.0880 Vj. 0.99959°k. 63.643 ms Give the solution for J and K ONLY ans (0.99959 degrees and 63.643 ms respectively)
A dc voltage equal to Vdc V is applied to a resistor of R Ω. Asinusoidal voltage equal to vs V is also applied to a resistor of R Ω.Show that the dc voltage will deliver the same amount of energy in Tseconds (where T is the period of the sinusoidal voltage) as thesinusoidal voltage provided Vdc equals the rms value of vs. (Hint:Equate the two expressions for the energy delivered to the resistor.)
1. What effect does changing the frequency on the effective value of sinusoidal voltage? 2. What effect does changing the amplitude on the effective value of sinusoidal voltage?
An AC circuits with 50 Hz voltage of 240V effective value is impressed on aninductance of sin(Y+2)/5 H. Y is the last digit of student matrix no. For example, astudent with the matrix number CD150012 will have the values of Y = 2, thereforesin(2+2)/5 H. i) Write the time equation for the voltage V(t) and the resulting current. Let thezero axis of the voltage wave be at t = 0.ii) Sketch the phasor diagram for this circuitiii) Find the maximum energy stored (joules) in the inductance.
b) Determine the voltage ?(?) and current ?(?) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors ?L, ?r and ?c. e) Sketch the phasor diagram showing ?s, ?r, ?r, ?c and ?.
Consider the given waveform of voltage and current vs. time: a. How many cycles of the voltage is presented in this graph? How many cycles of current? b. What is the peak value of the voltage presented in this graph? What is the peak value of the current?c. What is the sinusoidal equation for the voltage and current of this graph. d. Draw the phasor diagram of the voltage and current (with magnitude and direction).e. Is the current leading, lagging, or in phase with the voltage? If leading or lagging, by how much (write your answer in degrees).f. If these are the voltage and current waveforms of a specific circuit branch, what is the impedance of that branch? (Hint: Use Ohm's Law)
Consider the sinusoidal voltagev(t)=40 cos(100πt+60∘) V.1. What is the maximum amplitude of the voltage?2. What is the frequency in hertz?3. What is the frequency in radians per second?4. What is the phase angle in radians?5. What is the phase angle in degrees?6. What is the period in milliseconds?7. What is the first time after t=0 that v=−40 V?8. The sinusoidal function is shifted 10/3 ms to the right along thetime axis. What is the expression for v(t)?9. What is the minimum number of milliseconds that the functionmust be shifted to the left if the expression for v(t) is40 sin 100πt V?
A voltage is given by v(t)=50 sin(500πt+120°).. First, use a cosine function to express v(t). Then, find the angular frequency, the frequency in hertz, the phase angle, the period, and the rms value. Find the power that this voltage delivers to a 50-Ω resistance. Find the first value of time after t=0 that v(t) reaches its peak value. Sketch v(t) to scale versus time. * Denotes that answers are contained in the Student Solutions files. See See Appendix E for more information about accessing the Student Solutions.
If a current 5.0 A lags the applied voltage 230 V by an angle ϕ, it can be resolved into two components, OA in phase with the voltage and OB lagging by 90°. If the phasor diagram in to a circuit possessing resistance and inductance in series, OA and OB must not be labelled and respectively. It has become the practice to say that the power factor is laggingwhen the current lags the supply voltage, and leading when the current leads the supply voltage. This means that the supply voltage is regarded as the reference quantity. (a) A 30 μ F capacitor is connected across the applied voltage, 50 Hz supply. Calculate the reactance of 30 μ F capacitor connected across applied voltage (b) the reactance of the capacitor; (c) the current.
1. For the following sinusoids, determine which one leads and by how much a. ?(?) = 10cos (4? − 60°) and ?(?) = 6sin (4? + 50°)b. ?ଵ(?) = 4cos (377? + 10°) and ?ଶ(?) = −20cos(377?)c. ?(?) = 13 cos(2?) + 5 sin(2?) and ?(?) = 15cos (2? − 11.8°)