3/77 The square steel plate has a mass of 1800 kg with mass center at its center G. Calculate the tension in each of the three cables with which the plate is lifted while remaining horizontal. Ans. TA TB 5.41 kN, Tc 9.87 kN

3/77 The square steel plate has a mass of 1800 kg with mass center at its center G. Calculate the tension in each of the three cables with which the plate is lifted while remaining horizontal. Ans. TA TB 5.41 kN, Tc 9.87 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The five-bolt connection shown must support an applied load of P = 400 N. The thickness of the axial…

A: P = 400 kN t = 1 mm b = 16 mm

Q: : • Given that unit discharge in a rectangular channel is 18 m³/sec/ Im and the head loss across a…

A: Given data:Unit discharge (q) = 18 m3/shydraulic jump (HL) = 1.1 mAssume acceleration due to gravity…

Q: 2/ For the plan (hexagon shape) and section of the wall shown in No. 1. Calculate quantities for…

Q: A factory uses 2,00,000 litres of furnace oil (specific density .097) per month. If for one million…

Q: A Masonary Dam &m high, 1.5m wide at the top and 5m wide at the Base retains water to a depth of 7.5…

Q: In a 5000 m race, the athletes run 1212 laps; each lap is 400 m. Kara runs the race at a constant…

A: The total distance of the race, D=5000mEach lap distance = 400 mKara runs the race at a constant…

Q: What are the key considerations in designing transportation systems for emergency evacuation?

A: Designing transportation systems for emergency evacuation entails developing infrastructure and…

Q: Equilibrium of Force Systems Q11) Find the reaction moment at the built-in support at A due to the…

A: Given data -Cantilever beam with loading and moment P1 = 8 KN (downward)P2 = 5 KN (upward) M = 25 KN…

Q: Define precisely the difference between pavement serviceability and performance. Using a sketch to…

A: The key difference between pavement serviceability and performance lies in their focus:…

Q: 5.2 A one-story exterior platform is shown in the following figure. The roof is one-way slab. Answer…

A: a. 24 ft, 19 ftb. 4 inchesc. 250 psfd. 320 psfExplanation:

Q: Discuss the methods used for measuring soil density and compaction in the field.

A: Soil density and compaction are important concepts for construction and geotechnical engineers to…

Q: A two-story hospital is being designed in New Jersey. A) With a basic wind speed of 115 mph and wind…

Q: The 12.5-cm-diameter 20°C water jet in the figure strikes a plate containing a hole of 10.5-cm…

Q: دلها ↓↓ P 7 B vwx What is the Reaction Force induced in the following system at point A, if? Wo = 7…

A: A beam is given we need to find out the reaction at A

Q: The design stopping sight distance of a circular highway segment is 370 feet. The travel lane width…

Q: Explain the concept of soil stabilization and common stabilizing agents used in civil engineering.

A: Ground hardening is a technique applied in civil engineering to improve soil’s mechanical properties…

Q: SHOW COMPLETE SOLUTION 1. Reaction 2. Shear and Moment Diagram 3. Elastic Curve

A: Ra = 15 kNRb = 15 kNRc = 0 kNExplanation:Please see attach photo for the solutions thank you.

Q: ст ג'Tיוידי 61 Value: mm Value: cm 1 2 3 4 5 6 7 8 9 10

A: The main scale reading = 5.4mm Coinciding vernier division, (CVD) = 1Least count = 0.01mmThe vernier…

Q: A Stream El = 3636.5-ft ✗ Land Surface = 3641.5-ft Stream 3638.5-ft = Scale: 1 inch = 5-ft Figure 1.…

A: Hello studentPlease let me know the questionYou haven't mentioned the question herePlease share the…

Q: Order the following transportation modes by propulsive efficiency, with the lowest first. 1 2 ✓ […

A: The propulsive efficiency of transportation modes can vary significantly based on factors such as…

Q: Find the stress resultants N, V and M, draw the diagrams of the stress resultants (N,V,M). q =…

A: answer and diagrams are provided on the picture uploaded.Explanation:

Q: F6-10. Draw the shear and moment diagrams for the simply supported beam. 6 kN/m m- 3 m- F6-10

Q: How are contour lines determined in a topographic survey?

A: Contour lines are substantial features in topographic surveying as they represent imaginary lines…

Q: 1) Design a simply supported rectangular reinforced concrete beam for the span and service loads…

Q: How does transportation engineering address issues of equity, diversity, and inclusion in…

A: Equity, diversity, and inclusion (EDI) in infrastructure planning and development refers to the…

Q: In warm weather, how many days should a mason wait before laying concrete block on the footing? What…

A: For number of days should a mason wait before laying concrete block on footing is depends on various…

Q: Show step by step solution

A: The velocity of the jet is 12.1 bt/s, and the diameter of the jet is 4.28 inches. Therefore, there…

Q: Hitung frekuensi alami getaran bebas cerobong pada pondasi elastis (Gbr. P1-19), yang memungkinkan…

A: The objective of the question is to calculate the natural frequency of free vibration of a chimney…

Q: : The width of a horizontal, rectangular channel is reduced from 3.5 to 2.5 m and the floor is…

Q: The compound beam is fixed at E and supported by rollers at A and B. There are pins at C and D. Take…

Q: Consider the pin jointed truss accompanying figure and dete members BE. A 6 m B 15° 15° L 45° 8 m

Q: HIKI TO D OSHITENOJ ON DE No. Date 3 A parking facility operates from 8 a.m. to 6p.m, whereby 20% of…

A: Even with 90% efficiency (considering a buffer of 10%), the daily space-hours available are 9…

Q: As shown, two composite columns of steel and concrete are used to support a rigid platform. The…

A: F1 = 46.2 kNExplanation:Here is the solution:

Q: Explain the differences of transportation systems planning, analysis, evaluation, and asset…

A: The Four Pillars of Public Transit Systems: Planning, Analysis, Evaluation, and Asset…

Q: I will rate your answer, thanks.

A: Please refer below pages.If you have any doubts please feel free to ask.Explanation:Step 1:…

Q: 1. What are the primary phases of soil and how do their proportions affect soil properties?

A: Soil is a mixture of various constituents composed of solid particles, water, and air which interact…

Q: 2-35. Determine the reactions at the supports A and B. 500 lb/ft 30 ft 700 lb/ft 680 48 ft 48 ft…

Q: Construction Management

A: Below are the detailed discussion and explanations to each of the questions you asked…

Q: The assembly shown consists of a flywheel, a counterweight, and a bolt that attaches the…

A: (1) Mass per area of flywheel and hole diameter(2) Mass of the bolt and hole diameter

Q: 2.0 m ㅏ F 3.0 m q 4.0 m The above freely supported light uniform beam of length 10 m carries a point…

A: Determine the shear force and bending moment at x = 4m and x = 8m. Give the correct answers to two…

Q: If: fc'=4ksi, and fyt=60ksi Determine: 1- Shear diagram. 2- Maximum shear at d from face of support.…

Q: What are the different methods used for distance measurement in surveying?

A: One of the most important elements in surveying is measuring distances, crucial for engineering…

Q: 8.13 Refer to Figure P8.13. Det in the clay layer below the the net foundation load of 900 kN (net…

Q: The daily streamflow data at a site having a drainage area of 650 km² are given below. Compute (show…

A: Drainage Area = 650 km 2 Time ( days)Flow (m 3 / s…

Q: Pump inflow 2. Draw the HGL for the system shown below. The pump flow at A is 100 L/s with a 550 kPa…

A: Solution for this question is provided below ⬇️...Explanation:

Q: Determine the total sanitary sewer loading for the three pipes in the subdivision shown below. Also…

A: solve below calculationExplanation:Step 1: Step 2:Step 3: Step 4:

Q: If: fc'=4ksi, and fyt=60ksi Determine: 1- Shear diagram. 2- Maximum shear at d from face of support.…

Q: (a) 20 m? (b) 60 m? (c) 100 m?

A: Flow Rate =2 m3/secother data presented in the figure belowNeed to findPower output when efficiency…

Q: As shown in the figure, aluminum, E= 70GPa links (1) and (2) support rigid beam ABC. Link (1) has a…

Q: the A light weight Parachute has a diameter of 7m and total wt. including Pay load is 1020N. The…

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

3/77 The square steel plate has a mass of 1800 kg with
mass center at its center G. Calculate the tension in
each of the three cables with which the plate is lifted
while remaining horizontal.
Ans. TA TB 5.41 kN, Tc = 9.87 kN
A
D
2400
mm
G
C 1200 mm
1200 mm
1200 mm
2400 mm
B
Problem 3/77

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data:

VIEW

Step 2: Writing the coordinates Finding the position vector and unit vectors:

VIEW

Step 3: Equating the sum of all forces the forces equals to zero :

VIEW

Step 4: Finding the tensions in each cable of the given system:

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the bending moment 2.25 m to the right of point A for the beam shown below if P = 1705 N, T = 3205 Nm, a = 0.95 m, b = 0.97 m, and c = 1.15 m. Round of the final answer (in N m) to four decimal places
The 300N block rests upon a level plane for which the fk is 0.20. A force P = 100N, directed at 30° from the horizontal pulls the block and moves 80m starting from rest. If the 100N force is then removed, how much further will it travel?
Determine the magnitude of F so that the resultant couple moment acting on the beam is 1.5 kN.m clockwise ?
Write legibly and box the final answer. Determine the maximum mass (kg) that can be lifted at E if the 11.670-HP motor A has a maximum rotation speed of 301.20 rpm where the diameter of the shaft AB and CE are 10.237 mm and 15.402 mm, respectively. The allowable shearing stress is 1.001 GPa with F.S. of 1.76 for both shafts. Neglect the deformation of the cable at E. Where: radius of the gear at B, rB = 113.10 mm radius of the gear at C, rc = 158.58 mm
Calculate the critical shear Vu in kN.0
Why is the force Fd pointing downwards? By force equilibrium, shouldnt it be 3 + Fd = 9 Fd = 6kN, thus pointing upwards?
Determine the shear value (kN) when x = 2.2m from the left side of the beam where: L = 4.9 m; Wo = 131 kN/m
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Note that: a = 3.7 m b = 31.0 kN/m c = 35 kN Find the ff. A. Vertical reaction at B in kN. B. Moment reaction at A in kN-m. C. Deflection at point C in mm. D. Deflection at midspan of AB in mm.
The shorter legs of two 6”x 4” x ½” angles are welded to a 12”-20.7-lb channel. Determine the moments of inertia of the combined section with respect to centroidal axes respectively parallel and perpendicular to the web of the channel.
Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m and EI = 200MNm^2Determine the following;C. Slope at L/3. D. Deflection at L/3.
Compute the value of EI ϴ at the right end support. Wo = 19 kN/m, P =5 kN, L1 = 1.2m, L2 = 2.1m, L3 = 2.4m