The assembly shown consists of a flywheel, a counterweight, and a bolt that attaches the counterweight to the flywheel. The flywheel is uniform with mass per area of 2.25 g/mm2 and has a 40 mm diameter hole as shown. Determine the mass mc of the counterweight so that the center of mass of the assembly is at point O. The counterweight is attached to the flywheel by a bolt with mass mg=800 g that is screwed into a 10 mm diameter hole that passes completely through the flywheel. (Round the final answer to four decimal places.) flywheel 40 mm counterweight and bolt 45 mm 100 mm 50 mm The mass imc of the counterweight is mc.mB 9

The assembly shown consists of a flywheel, a counterweight, and a bolt that attaches the counterweight to the flywheel. The flywheel is uniform with mass per area of 2.25 g/mm2 and has a 40 mm diameter hole as shown. Determine the mass mc of the counterweight so that the center of mass of the assembly is at point O. The counterweight is attached to the flywheel by a bolt with mass mg=800 g that is screwed into a 10 mm diameter hole that passes completely through the flywheel. (Round the final answer to four decimal places.) flywheel 40 mm counterweight and bolt 45 mm 100 mm 50 mm The mass imc of the counterweight is mc.mB 9

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two discs with weights WA and WB, a negligible AB They are attached to the two ends of the rod from their centers. For equilibrium position Calculate the value of α. (WA = 50 N; WB = 200 N)
Given the problem: The smooth disk shown in the figure is pined at 'D' and has a weight of 24.6 lb. Neglecting the weights of the other members, determine the following: a.) Total reaction at 'A' in lb. b.) Horizontal component at 'B' in lb. c.) Vertical component at 'B' in lb. *Round off final answer in 4 decimal places. Thank you.
3. Three bars each made from different materials are placed between walls when the temperature is 14°C. Determine the support reaction when the temperature becomes 19°C. The material properties are given in the figure Answer: R= 3502.30 N
a 90 kg smooth circular cylinder A with a radius of 0.6m is held in equilibrium by a cord CD and a bar BC of negligible mass. The length of bar is 2.4m.
Two masses are attached to a uniform meter stick as shown in the figure below. Themasses of m1 and m2 are as given and the meter stick weighs 150 g. A force F withunknown magnitude is applied on one end of the stick at an angle of 30° to balancethe system. (a) What is the magnitude of F? (Ans: 6.21 N)(b) What are the reaction forces on the support? (Ans: Rx = 5.38 N; Ry = 5.80 N)
The 10 kg C sphere is released from rest when θ= 0 degrees and the tension in the spring is 100 N. Determine the velocity of the sphere when θ = 90 degrees. Neglect the mass of the AB rod and the size of the sphere.
34. In the Figure, the homogeneous block weighs 300 kg and the coefficient of friction is 0.45. If h = 50 cm, determine the force P to cause motion to impend. (A) 72 kg (B) 240 kg (C) 300 kg (D) None of the Above (E) 108 kg
The two blocks shown start from rest. The horizontal plane and the pulley are frictionless, and the pulley is assumed to be of negligible mass. Determine the acceleration of each block and the tension in each cord. A= 100 kg B = 260 kg
The rotating stepped shaft in the figure is produced from 85080M30 steel by machining method. It works at ambient temperature. If the force applied to the shaft is given as P=10 kN as constant, calculate the diameter d for the shaft to have an infinite life.(f=0.9) (Sut=600MPa)
The pendulum shown consists of two thin rods each having a weight of 10 lb. Determine the pendulum’s mass moment of inertia about an axis passing through (a) the pin at O, and (b) the mass center G of the pendulum.
Please plug in the value for (ii) and solve it
The cantilever steel beam as shown below has the rectangular cross section shown, determine the maximum displacement of the beam use E=200 GPa for the modulus of elasticity 200mm 4 KN/m 6 KN .m 350mm 2m 2m 1m