38- A blanking operation is to be performed on 8.0 mm thick soft cold rolled steel. The part is circular with diameter= 90.0 mm. Determine the appropriate punch size for this operation (Punch diameter = Db - 2c) Clearance allowance value for Metal Group 1100S and 5052S aluminum alloys, 0.045 all tempers Ac 2024ST and 6061 ST aluminum 0.060 alloys; brass, all tempers; soft cold- rolled steel, soft stainless steel Cold-rolled steel, half hard; stainless steel, half-hard and full- hard 0.075

38- A blanking operation is to be performed on 8.0 mm thick soft cold rolled steel. The part is circular with diameter= 90.0 mm. Determine the appropriate punch size for this operation (Punch diameter = Db - 2c) Clearance allowance value for Metal Group 1100S and 5052S aluminum alloys, 0.045 all tempers Ac 2024ST and 6061 ST aluminum 0.060 alloys; brass, all tempers; soft cold- rolled steel, soft stainless steel Cold-rolled steel, half hard; stainless steel, half-hard and full- hard 0.075

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

158) Which ones are used in mold making?A) clay and waterB) sand-water-clayC) sand-water-resinD) silica-water-pasteE) clay-water-resin 129) Which means the closeness of the measured value to the true value?A) precisionB) precisionC) error coefficientD) toleranceE) measurement sensitivity 76) Which shows perfectly elastic behavior?A) copperB) thermosetC) elastomerD) aluminumE) stainless steel 82) Which is true for low alloy Steels?A) they contain less than 1% of additional alloying elements in totalB) contain less than 2% of additional alloying elements in totalC) contain less than 3% additional alloying elements in totalD) contain less than 4% additional alloying elements in totalE) contain less than 5% additional alloying elements in total
Temper drying or tempering a quench harden steel part reduces the brittleness of a part. It also reduces the ultimate -------? strength and -------? strength of a part. However the tempering process also increases the materials ----?as measured by the percent elongation.
31 - Which of the following is not one of the strengthening methods of steels.A) Cold drawingB) RollingC) Deformation hardeningD) Application of the prestressing techniqueE) Reduce the amount of carbon
The percent elongation of a 1040 steel, cold worked 17% is ________________ . Note report answer to the nearest 2 ksi.
•42- Which is not a copolymer type?a) blockB) wavyC) casuallyD) graftE) complex •44- Which one is not used to indicate geometric features in technical drawing?a) sizeB) angularityC) toleranceD) smoothnessE) surface defect
26 Q2. Illustrate the Hot working process with neat sketch, along with the any four classification of hot working.
30- After which step during the tensile test the force starts to decrease?A) at the start of the experimentB) with the onset of neckingC) by breakingD) during uniform elongationE) when it reaches the pour point •31- Which of the following process steps do the particle processing techniques of metals and ceramics include?A) meltingB) tattooC) plastic deformationD) machiningE) sintering •32- Which of the following is the machine in which the extrusion process is made?A) paint canB) millingC) tattoo hammerD) rolling standE) press or torch
Materials, properties and testing Describe the effect bend testing have on the physical properties of steel.
9. The top view shows a bend radius of the thin metal. Would a bend radius of 1/8" meet the requirements? Review questions based on previous units:
1. Write the requirements of good pattern.2. What is core venting? 3. Which process is called lost waxing method? Why? answer all the 3 parts
Did I get these right?
Manufacturer process A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength = 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking. Take: Ac=0.06