I need answer within 20 minutes please please with my best wishes is a sheet metal forming process performed by placing a sheet-metal blank over a die cavity and then6)pushing the metal into the opening using a punch & Blank holder to make box-shaped parts.7)forming temperature condition.In blanking opcration, if thc final blank diameter is 200 mm & the clearance is 1.5 mm, then the Die size should be9)Products possess (shows) better reproducibility in metal forming at8)Cold working of metals decreases10) Sheet metal bending involvesproperty in the work piece.&stresses and strains.

Answered: Image /qna-images/answer/70864b15-4825-4f0b-9868-87a6b0765f5e.jpg

6) is a sheet metal forming process performed by placing a sheet-metal blank over a die cavity and then pushing the metal into the opening using a punch & Blank holder to make box-shaped parts. 7) Products possess (shows) better reproducibility in metal forming at tt. forming temperature condition. 8) In blanking operation, if the final blank diameter is 200 mm & the clearance is 1.5 mm, then the Die size should be 9) Cold working of metals decreases property in the work piece. & 10) Sheet metal bending involves stresses and strains. dition

6) is a sheet metal forming process performed by placing a sheet-metal blank over a die cavity and then pushing the metal into the opening using a punch & Blank holder to make box-shaped parts. 7) Products possess (shows) better reproducibility in metal forming at tt. forming temperature condition. 8) In blanking operation, if the final blank diameter is 200 mm & the clearance is 1.5 mm, then the Die size should be 9) Cold working of metals decreases property in the work piece. & 10) Sheet metal bending involves stresses and strains. dition

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q#4:(a) Explainthe advantage of corner radii of punch and die in Sheet Metal Drawing Process.
A drawing operation is used to form a cylindrical cup with inside diameter of 75 mm and height of 50 mm. The starting blank size is 140 mm and the stock thickness is 2.4 mm. Based on the data, is the operation feasible?
The average number of articles produced by two machines per day are 200 and 250 with S.D 20 and 25 respectively on the basis of records of 25 days production.Can you regard both the machines equally efficient at 1% level of significant?
An automated blanking and forming line is designed to from 2 mm thick sheet, made from 2024 Aluminum, T4 temper, into a square sheet metal part. Elongation at 50mm 20% Young’s Modulus 70GPa Yield strength 325 MPa UTS 470 A) What is the force required to punch a square piece that is 500 mm on each edge? B) If the sheet blank was bent to a radius of 5 mm, what will be the radius after springback occurs? C) What is the required bend angle to achieve a 90° final bend angel for a bend radius of 5 mm?
Forging procedures may be classified in part by how much room there is for movement in the die. Please identify the three primary classes that this system generates.
In your own words, state and justify your assumptions and comment on your working.Marks will be assigned for the quality of the presentation of the working and od the comments.
7 The example for forming process is ___________. a. Tempering b. Drawing c. Gas welding d. Die Casting
(USCS units) A turning operation is performed using a rake angle of 15°. Cutting speed = 200 ft/min, feed= 0.012 in/rev, and depth of cut = 0.100 in. The chip thickness ratio measured after the cut = 0.48. Determine (a) chip thickness after the cut, (b) shear angle, (c) friction angle, (d) coefficient of friction, and (e) shear strain (USCS units) The turning operation in the previous problem involves a work material whose shear strength = 52,000 lb/in2. Based on your answers to the previous problem, compute (a) shear force, (b) cutting force, (c) thrust force, and (d) friction force.
Q#1: (a) Explain the advantage of corner radii of punch and die in Sheet Metal Drawing Process. (b) Explain the disadvantages of Tube Drawing process in which mandrel is not used.
1) Selection of die in forging process is very important in order to control the quality of the product. List four general requirements for die material.
In a factory where there are three shifts: The machine overhead cost is found to be £8.20 / hr, the labour overhead cost is found to be £30.20/hr, and the premises overhead cost is found to be £3.50/hr. Using the principle of overhead costing: If a single component takes 23 minutes to manufacture on the milling machine. What is the cost / part? You should include machine costs, labour costs and premises costs in your answer, but you can neglect material and energy costs. Express your answer in £ rounded up to the nearest penny.
1: What is the difference between casting and forging process.