•4-33. The steel pipe is filled with concrete and subjected to a compressive force of 80 kN. Determine the average normal stress in the concrete and the steel due to this loading. The pipe has an outer diameter of 80 mm and an inner diameter of 70 mm. Eg = 200 GPa, E̟ = 24 GPa. 80 kN 500 mm

Q: The assembly consists of two sections of galvanized steel pipe connected together using a reducing…

A: Given, For Shaft AB, do = 0.75 in ; ro = 0.375 in di = 0.68 in  ; ri = 0.34 in For Shaft BC, do = 1…

Q: Air is pumped into the steel thin-walled pressure vessel at C. If the ends of the vessel are closed…

A: Write the given data.

Q: If the allowable normal stress for the bar is s allow = 120 MPa, determine the maximum axial force P…

A: Write the given data:

Q: 10-7. The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is…

A: Given data: The outer diameter of the copper pipe is do=40 mm. The inner diameter of the copper…

Q: P7-5. The lever is held to the fixed shaft using the pin AB. If the couple is applied to the lever,…

A:

Q: 7-13. The blade of the hacksaw is subjected to a pretension force of F-100 N. Determine the…

A: Given data: *The pretension force subjected in the blade of the hack saw is F=100 N. *The vertical…

Q: *7-44. The plastic block is subjected to an axial compressive force of 600 N. Assuming that the caps…

A: Given: The axial compressive force acting on the horizontal plane is F1=-600 N The inclination of…

Q: If the allowable tensile stress for wires AB and AC is sallow = 180 MPa, and wire AB has a diameter…

A:

Q: Please Show work clearly and show free body diagram if possible and be sure with the positive and…

A:

Q: 7-23. The metal stud punch is subjected to a force of 120 N on the handle. Determine the magnitude…

A:

Q: 3-29. The friction pad A is used to support the member, which is subjected to an axial force of P= 2…

A: GivenP=2kNE=4MPaμ=0.4w=50mm

Q: F8-12. If the elongation of wire BC is 0.2 mm after the force Pis applied, determine the magnitude…

A: elongation of wire BC 8= 0.2 mmd= 3 mm , l= 300 mm→ For A-36 steel ,    E= 200 GPa    σy= 250 MPa

Q: 1-70. The jib crane is pinned at A and supports a chain hoist that can travel along the bottom…

A:

Q: The copper pipe has an outer diameter of 3 in. and an inner diameter of 2.50 in. If it is tightly…

A: Given data

Q: The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly…

A: Given, Outer diameter = 40 mm=0.04m Outer radius = 0.02m Inner Diameter = 37 mm=0.037m inner radius…

Q: Q4/ The aluminum bracket A is used to support the centrally applied load of 8 kip. If it has a…

A: Now draw the free body diagram of bracket,

Q: The assembly consists of a solid 15 mm diameter rod connected to the inside of a tube using a rigid…

A:

Q: If P = 15 kN, determine the average shear stress in the pins at A, B, and C. All pins are in double…

A: Given: The value of load, P = 15 kN The diameter of pin, d = 18 mm = 0.018 m   The free body diagram…

Q: 7-6. Determine the resultant internal normal and shear force in the member at (a) section a-a and…

A: According to given condition for part a, ∑Fx=0Na-2000=0Na=2000 N∑Fy=0Va=0 N

Q: The tank of the air compressor is subjected to an internal pressure of 90 psi. If the inner diameter…

A: Write the given data: Understand that the stress generated at point A will be the tangential stress…

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 2…

A: Given:- P=2kip,Width of section of bar with hole,w1=1.875 inch,Width of section of bar without…

Q: The rod has a diameter of 1 in. and a weight of 15 lb>ft. Determine the maximum torsional stress…

A: Given: The diameter of rod is D = 1 in. The weight of the rod is M = 15 lb/ft. The length of the…

Q: 8-10. The A-36-steel band is 2 in. wide and is secured around the smooth rigid cylinder. If the…

A: Given:Tension, F=400 lbthickness, t=18 inwidth=2 in

Q: 7-83. The pin-connected rigid rods AB and BC are inclined at e- 30° when they are unloaded. When the…

A: Consider the diagram shown below for the initial condition.

Q: 2-9. If a horizontal load applied to the bar AC causes point A to be displaced to the right by an…

A:

Q: The rod has a diameter of 40 mm. If it is subjected to the force system shown, determine the stress…

A: Understand that the point A lies on the outer periphery of the shaft on the z axis. The Torsional…

Q: 7-42. If P- 15 kN, determine the average shear stress in the pins at A, B, and C. All pins are in…

A: As per given condition∑Fx=0Ax-FBCcos 30°=0but here FBC not…

Q: *7-28. The supporting wheel on a scaffold is held in place on the leg using a 4-mm-diameter pin. If…

A: Given Data: The diameter of the pin is d = 4 mm. The normal force acting on the wheel is P = 3 kN.…

Q: R8-6. The head H is connected to the cylinder of a compressor using six steel bolts. If the clamping…

A: Given Data: Clamping force on bolt is F = 4 kN. Modulus of elasticity is Est = 200 GPa. Yield…

Q: The lever is held to the fixed shaft using the pin AB. If the couple is applied to the lever,…

A: Given figure,  Take a point O in the centre on the line AB.

Q: F8-6. Determine the state of stress at point A on the cross section of the pipe assembly at section…

A:

Q: The rib-joint pliers are used to grip the smooth pipe C. If the force of 100 N is applied to the…

A: Given: The magnitude of the force applied on the handles is FH=100 N. The length and breadth of the…

Q: 4-6. The bar has a cross-sectional area of 3 in', and E = 35(10³) ksi. Determine the displacement of…

A:

Q: The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is…

A: Given: The thickness of the wall is t=0.025 in. The inner diameter of the wall is d=0.5 in. The…

Q: Q3: The yoke-and-rod connection is subjected to a tensile force of 15 kN. Determine the average…

A: Dear student,                     According to the guidelines I am allowed to answer only one…

Q: The plate has a width of 0.5 m. If the stress distribution at the support varies as shown, determine…

A: Writing equilibrium equations:→∑FY=0 ⇒-P+∫04[(15.x)×(dx×0.5)]=0⇒P=15×23×[x23] 04×0.5⇒P=40 MNNow…

Q: The plastic tube is subjected to a torque of 150 N # m. Determine the average shear stress in the…

A: Torque=150 N-m =150×103 N-mm ; mean dimension (a) =200 mm ; thickness (t)=3 mm ;…

Q: 7-67. If the allowable shear stress for each of the 10-mm-diameter steel pins at A, B, and Cis Tllo…

A: The free body diagram of beam is as follow: calculate the moment about point A is as follows:…

Q: 0-13. The assembly consists of two sections of galvanized steel pipe connected together using a…

A: Given Data: The coupling force is F = 75 N. The coupling arm is l = 350 mm. The inner and outer…

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 2…

A: At fillet rh=0.251.25=0.2wh=1.8751.25=1.5   From the table  The stress concentration factor,  K=1.73

Q: *7-48. The joint is subjected to the axial member force of 27 kN. Determine the average normal…

A: Given data: Length of section AB, LAB = 40 mm. Length of section BC, LBC = 112 mm. The thickness of…

Q: The railcar docklight is supported by the 1 8-in.-diameter pin at A. If the lamp weighs 4 lb, and…

A: Moment at point A is given by:⇒MA=(4×3)+(0.5×3×32)⇒MA=14.25 lb.ft⇒MA=171 lb.in...........(since 1…

Q: F7-12. Determine the average normal stress in rod AB if the load has a mass of 50 kg. The diameter…

A: Given data m=50 kgd=8 mm

Q: 4-33. The steel pipe is filled with concrete and subjected to a compressive force of 80 kN.…

A: In this question, steel is filled with concrete, the compressive force is applied at one end and…

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN,…

A:

Q: Determine the maximum distance d to the edge of the plate at which the force P can be applied so…

A: Given, Load=P Distance of the load from the bottom=d Thickness of the plate= 200mm Solution Tensile…

Q: 6-105. The member has a square cross section and is subjected to a resultant internal bending moment…

A:

Q: 7-38. If the average normal stress in each of the 20-mm-diameter bars is not allowed to exceed 150…

A: At equilibrium, Taking Moment about point A, ∑MA=0 2RBy=1.5PRBy=0.75P Also, ∑Fx=0RAx=-P…

Q: The steel pipe is filled with concrete and subjected to a compressive force of 75 kN. Determine the…

A:

Q: F7-17 The strut is glued to the horizontal member at surface AB.If the strut has a thickness of 25…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.