4- A helical compression spring is made with oil-tempered wire with wire diameter of 0.2 in, ean coil diameter of 2 in, a total of 12 coils, a free length of 5 in, with squared ends. a) Find the solid length. b) Find the force necessary to deflect the spring to its solid length. c) Find the factor of safety guarding against yielding when the spring is compressed to its solid ngth.

4- A helical compression spring is made with oil-tempered wire with wire diameter of 0.2 in, ean coil diameter of 2 in, a total of 12 coils, a free length of 5 in, with squared ends. a) Find the solid length. b) Find the force necessary to deflect the spring to its solid length. c) Find the factor of safety guarding against yielding when the spring is compressed to its solid ngth.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
A spring leaf is made with an unknown material and has a width of 2.7 inches, a thickness of 5/16 inches, and a length of 1 yard. The leaf spring has 2 full-length leaves and 5 graduated leaves. For a load of 1.5 kN, the leaf spring deflects 115 mm. A.) Find the modulus of elasticity of the spring steel used in the leaf spring in ksi. B.) Using the modulus of elasticity, find the stress experienced by the material in MPa of the strain is 0.015. Answer in the Given-Required-Solution format. Show the unit analysis and the answer should be at least in 4 decimals. Subject: Machine Design
Two coaxial closed coil springs make up a standard compound helical spring. When both springs are unloaded, they are not of equal length. If each spring's working stress is to be the same. The wire material has an 80 GPa modulus of rigidity. Find the diameter of steel wire for inner spring and stiffness of inner spring. Also find the stiffness of the compound spring. Outer spring a: Mean coil diameter = 100 mm No. of turns = 15 Wire diameter = 12.5 mm Inner spring b: mean coil diameter = 75 mm No. of turns = 20
Question 1) A compression coil spring made of an alloy steel is having the followingspecifications :Mean diameter of coil = 50 mm ; Wire diameter = 5 mm ; Number of active coils = 20.If this spring is subjected to an axial load of 1000 N ; calculate the maximum shear stress(neglect the curvature effect) to which the spring material is subjected.
Three extension springs are hooked in series and supports a weight of 70 kg. One spring has a rate of 0.209 kg ∕mm and the other two have equal spring rate of 0.643 kg ∕mm. Find the deflection.
A spring sustains 200 ft-lb of energy with a deflection of 3’’. Assume that the mean coil diameter is 7 times the wire diameter and that the allowable stress is 100ksi. Determine the wire diameter.
A helical compression spring having 14 active coils is close coiled. It has a spring stiffness of 400lb/in. It is cut into two springs having 6 and 8 turns. Determine the spring stiffnesses of resulting springs.
A helical compression spring has a scale of 500 lb/in., an outside diameter of 2.75 in, a free length of 8 inches and with squared and ground ends. The load is 1,000 lbs and the working stress on the wire material is 65000 psi. If the Wahl factor of 1.25 is to be used, calculate the following: A. The standard wire diameter B. The number of active coil if G = 10 800 000 psi C. The solid height D. The stress at solid height
5.1 Determine the spring constant of the spring arrangement if all springs have the same spring constant. 5.2 In a compound helical spring, the inner spring is concentric with the outer spring, but is 9 mm shorter. The outer spring has ten coils of mean diameter 24 mm, and the wire diameter is 3 mm. Find the stiffness of the inner spring if an axial load of 150 N causes the outer spring to compress 18 mm. If the mean coil diameter for the inner spring is 15.94 mm, find the wire diameter of the inner spring when it has eight coils. Both the springs are made of the same material having G = 77 GPa.
PROBLEM:2 A spring made from a wire of 2.5 mm diameter and 750 N/sq. mm. as its working stress Mean diameter of 12.5 mm and 15 active coils. Find (a) Stiffness of the spring (b) solid length. Assume that the ends are squared and ground. Take modulus of rigidity as 0.85x105 N/mm2.
Subject : - Mechanical Engineering A helical spring is provided with a rigid plate at each end.A bolt passes through the spring and the endplates. By turning the nut, the spring is compressed until the coils touch. The height of the unloaded spring is 600 mm, its mean coil diameter is 100 mm and the diameter of the spring wire is 28 mm. The spring has 18 coils. The diameter of the bolt is 25 mm and each plate is 25mm thick. Calculate the elongation of the bolt when the spring is fully compressed as well as the stress in the spring wire ( E = 200 GPa and G = 80 GPa )
A helical spring is made of 10 m diameter steel wire wound on a 100 mm diameter mandrel. If there are 10 active coils what is spring constant Take: C= 100 GPA What force must be applied to the spring to elongate it by 50 mm?