4) A simply supported beam supports the uniformly distributed load of intensity Wo. Determine the safe allowable value of w, if the flexural stress is limited to 160 MPa in tension, 200 MPa in compression, shear stress is limited to 70 MPa and maximum allowable deflection is 15mm. The modulus of elasticity of the beam is 200 GPa. Use Moment Area Method.

4) A simply supported beam supports the uniformly distributed load of intensity Wo. Determine the safe allowable value of w, if the flexural stress is limited to 160 MPa in tension, 200 MPa in compression, shear stress is limited to 70 MPa and maximum allowable deflection is 15mm. The modulus of elasticity of the beam is 200 GPa. Use Moment Area Method.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PLEASE ANSWER ASAP TY! A 2-m long cantilever beam carries a uniformly distributed load of 10KN/m over its entire length. The beam has a rectangular cross-section with dimensions 200 mm wide and 400mm high. a) Determine the maximum flexure stress in the beam (in MPa). b) Determine the moment of inertia about the neutral axis of the cross-section (in mm4) c) Determine the magnitude of bending moment at a section 0.5m from fixed support (in KN-m). d) Determine the absolute maximum bending moment along the length of the beam (in KN-m).
A timber beam having a simple span of 6m carries a total load including its own weight of 15KN/m. It has a width of 250 mm and a depth of 300mm. Used dressed dimension by reducing its dimension by 10mm. The wooden section is made up of 80% Apitong.Fb = 16.5 MPaEw = 7310 MPaFv = 1.75Mpaa. Determine the maximum flexural stress of the beam.b. Determine the maximum shearing stress of the beam.c. Determine the maximum deflection of the beam.
A single-span beam having unsupported length of 8m. has a cross section of 200mm x 350mm. (use nominal dimension). It carries a uniformly distributed load “W” kN/m throughout its span. Allowable bending stress is Fb=9.6 MPa and a modulus of elasticity of 13800 MPa. From the table, the effective length Le=1.92 Lu where Lu=unsupported length of beam. a. Compute the allowable bending stress with the size factor adjustment in MPA Round your answer to 3 decimal places. b. Compute the allowable bending stress with lateral stability adjustment in MPa Round your answer to 3 decimal places. c. Compute the safe uniform load “W” that the beam could carry in KN/m. (choose the smallest of prob. a and b.) use M=wl^2 / 8 Round your answer to 3 decimal places.
Figure Q6b shows a simply supported 3.75 m long beam with a solid round crosssection and a concentrated point load of 250 kN acting at the mid-point of the beam.If the diameter of the beam cross-section is 165 mm, calculate the maximum tensilestress [σtensile_max] and the maximum compressive stress [σcompressive_max] experiencedby the beam. Use Ixx = [πr^4/4] for the second moment of area of a round section beamabout its x-x centroid axis. Assume that the weight of the beam is zero and that thebeam section is solid and uniform along its entire length. Give your answer in N/mm2to 2 decimal places.
A simple beam of length L = 3.2m is subjected to a uniform load of 70 kN/m. The beam (see figure), made up of wood flanges and steel side plates, has the ff dimensions: wood flanges 75mm x 100 mm, and steel plates are 300 mm deep. Take the moduli of elasticity for the steel and wood to be 210 GPa and 10 GPa, respectively. What is the required thickness t of the steel plates if the allowable stresses are 120 MPa for the steel and 6.5MPa for the wood? Hint: transform steel into wood. (Express your answer in mm, up to 1 decimal place)
A reinforced concrete beam, b by h with tensile reinforcement of 6-25mm diameter bars is simply supported on a clear span of 12m. Given: fc = 12 MPa fs = 140 Mpa wc = 24 kN/m3 n = 12 b = 331 mm h = 602 mm d = 582 mm determine the ff. 1. What is the distance from the top fiber of the beam to the neutral axis in mm? 2. What is the gross moment of inertia of the section in mm4? 3. Compute the moment capacity of concrete in kN-m. 4. Compute the moment capacity of steel in kN-m. 5. Aside from the uniformly distributed self-weight of the reinforced concrete, what will be the maximum two equal concentrated loads it can carry that will be located at its third points in kN? pls solve completely
A single-span beam having unsupported length of 8m. has a cross section of 200mm x 350mm. (use nominal dimension). It carries a uniformly distributed load “W” kN/m throughout its span. Allowable bending stress is Fb=9.6 MPa and a modulus of elasticity of 13800 MPa. From the table, the effective length Le=1.92 Lu where Lu=unsupported length of beam. a. Compute the allowable bending stress with the size factor adjustment in MPA b. Compute the allowable bending stress with lateral stability adjustment in MPa c. Compute the safe uniform load “W” that the beam could carry in KN/m. (choose the smallest of prob. a and b.) use M=wl^2 / 8
A W 10 x 30 is used as a beam to support a concrete floor system. The floor is to carry a total load of 4.2 kPa. The beam is simply supported over a span of 8.4 m. The properties of the section are as follows: Depth = 254 mm Thickness of web = 19.2 mm Moment of Inertia = 98 x 106 mm4 Section modulus = 530 x 103 mm3 Weight = 44.86 k9/m Assume the beam is laterally supported over its length and that the allowable stress in bending is 0.66 Fy and in shear on gross section is 0.4Fy . Use A36 steel with Fy = 250 MPa. Determine the center-to-center spacing of the beams without exceeding the allowable shear stress. Determine the center-to-center spacing of the beams without exceeding the allowable bending stress. Which will be the center-to-center spacing of the beams to consider?
A timber beam having a simple span of 15m carries a total load including its own weight of 25KN/m. It has a width of 200 mm and a depth of 250mm. The wooden section is made up of 80% Apitong.Fb = 17.5 MPaEw = 7510 MPaFv = 1.85Mpaa. Determine the maximum flexural stress of the beam.b. Determine the maximum shearing stress of the beam.c. Determine the maximum deflection of the beam.
1. Three concentrated loads of 50kN, 30KN and 60 kN are loaded on a 14-meter-span fully-restrained beam and each applied at 7 m, 9m and 11 m from the left support respectively. Which of the following most nearly gives the elastic section modulus of the beam (in mm³) if the shape factor is 1.4 and the yield stress is 240 MPa. a.443.667 b. 546.778 c. 488.775 d. 505.952 e. 521.345 2. A W 14 x 68 having the following properties:Prop. of W 14 x 68d = 356.62 mm Sx = 1688 x 10³ mm³ Cb = 1.14bf = 254.89 mm Zx = 1885 x 10³ mm³ Lp = 2.65 mtf = 18.29 mm E = 200000 MPa Lr= 8.05 mFy = 345 MPa Elastic buckling stress: Fcr = 420 MPa Which of the ff. most nearly gives the flexural strength of the beam if the beam has an unbraced length of 12 m. a. 450 b. 709 c. 638 d. 486 e. 585 Which of the ff. most nearly gives the flexural strength of the beam if the beam has an unbraced length of 6 m. a. 585 b. 709 c. 638 d. 450 e. 486
A flooring system consist of I-beam sections spaced at 3 m(center to center) and with simple spans of 6 m. The beams support a 200 mm thick slab. The flooring system is designed for a live load of 2400 N/m² as well as ceiling load of 750 N/m². The properties of the I-beam sections are : d = 352 mm, weight of beam = 440 N/m, moment of inertia , Ix = 0.0012 m⁴. Consider Fy = 248 MPa, E = 200000 MPa and wt. of concrete of 24 kN/m³. 1. Which of the following most nearly gives the uniform pressure acting on the slab? a. 6.2 kPa b. 7.95 kPa c. 5.2 kPa d. 6.10 kPa 2. Which of the following most nearly gives the total uniform load on the beam in kN/m? a. 19.71 kN/m b. 17.82 kN/m c. 24.29 kN/m d. 28.14 kN/m 3. Which of the following most nearly gives the initial stress on the beam due to deadload only assuming no shoring during construction? a. 12.1 MPa b. 8.91 MPa c. 10.4 MPa…
Determine the concentrated load at midspan that can be added if theuniformly distributed load ω is 58 N/m that can beloaded for the beam shown if the allowable bending stress fortension is 80 MPa;, for compression is 130 MPa , for shearing stressis 48 MPa without exceeding deflection limit of L/360. E for steel is200 GPa.