4- Consider an OP amp connected to the inverting configuration to realize a closed-loop gain of -50 V/V utilizing resistors o f1 k2 and 50 kQ. A load resistance RL is connected from the output to ground, and a low-frequency sine wave signal of peak amplitude Vp is applied to the input. Let the OP amp be ideal except that its output voltage saturates at +/- 10V and its output current is limited to the range +/-15 mA. For RL = 1 k, what is the maximum possible value of Vp while an undistorted output sinusoid is obtained?

4- Consider an OP amp connected to the inverting configuration to realize a closed-loop gain of -50 V/V utilizing resistors o f1 k2 and 50 kQ. A load resistance RL is connected from the output to ground, and a low-frequency sine wave signal of peak amplitude Vp is applied to the input. Let the OP amp be ideal except that its output voltage saturates at +/- 10V and its output current is limited to the range +/-15 mA. For RL = 1 k, what is the maximum possible value of Vp while an undistorted output sinusoid is obtained?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

A certain op-amp has three internal amplifier stages with midrange gains of 30 dB, 40 dB, and 20 dB. Each stage also has a critical frequency associated with it as follows: fc1 = 600 Hz, fc2 = 50 kHz, and fc3 = 200 kHz. (a) What is the midrange open-loop gain of the op-amp, expressed in dB? (b) What is the total phase shift through the amplifier, including inversion, when the signal frequency is 10 kHz?
Please answer this two part question A) It is known that when an Op-amp is operated using the negative feedbackconfiguration, the output impedance reduces. Derive an expression that proves this. B) It is known that when an Op-amp is operated using the positive feedbackconfiguration, the output impedance increase. Derive an expression that proves this.
Consider an inverting amplifier with a nominal gain of 1000, an op amp with an input offset voltage of 3 mV and an output saturation voltage of plus or minus 10 V. (a) Find the peak value (approximately) of the sine wave input signal that will not cause the output voltage to be cut off? (b) If the effect of Vos is zero at room temperature (25°C): (I) if the circuit operates at a predetermined temperature; (ii) the temperature coefficient of Vas is known to be 10μV/°C, and the circuit is operable In the range of 0°C to 75°C. Please find the maximum signal we can input in the two cases respectively.
Suppose the op amp shown has an fT of 3 MHz. What is the phase margin of the ampliﬁer?
The open-loop gain A of real (nonideal) op-amps isvery large at low frequencies but decreases markedlyas frequency increases. As a result, the closed-loopgain of op-amp circuits can be strongly dependent on frequency. Determine the relationship between a finiteand frequency-dependent open-loop gain AV(OL)(ω)and the closed-loop gain AV(CL)(ω) of an invertingamplifier as a function of frequency. Plot AV(CL)versus ω. Notice that −RF/RS is the low-frequencyclosed-loop gain.
A single-pole op amp has an open-loop gain of 92 dB and a unity-gain frequency of 1 MHz. What is the open-loop bandwidth of the op amp? (a) The op amp is used in a noninverting ampliﬁer designed to have an ideal gain of 32 dB. What is the bandwidth of the noninverting ampliﬁer? (b) Repeat for an inverting ampliﬁer with and ideal gain of 32dB.
a) Design an inverting amplifier with a gain of 4. Use an ideal op amp, a 30 kohm resistor in the feedback path, and +-12 v power supplies. b) Using your design from part a, determine the range of input voltages that will keep the op amp in it's linear operating region. c) suppose you wish to amplify a 2 V signal, using your design from part a, with a variable feedback resistor. What is the largest value of feedback resistance that keeps the op amp in its linear operation region? Using this resistor value, what is the new gain of the inverting amplifier?
Consider the active circuit with the schematic:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem. c. If L = 1H, sketch the straight-line approximation of the Bode plot for the circuit’s gain assuming the op amp can still be considered as ideal.d. The op amp you select turns out to be non-ideal, and it has a real pole at wC = 1krad/s. Write the updated transfer function for your circuit (using your values of R1, R2, and L = 1H). Make it in the canonical form.e. Sketch the straight-line approximation of the Bode plot for the circuit with your updated transfer function from D.
Consider the active circuit with the schematic:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem.
The op amp in the circuit of Figure is ideal.a) What op amp circuit configuration is this?b) Find ?0 in terms of ??.c) Find the range of values for ?? such that ?0 does not saturate and the op ampremains in its linear region of operation.
Given circuit, assume op-amp is ideal. What is the input resistance of the circuit, RIN? What are the currents in the inputs of op-amp? i-=? i+=? What is the output resistance of the circuit, ROUT=? Find voltage VA and VB? What is the nodal equation (KCL) at node VB? Solve for VOUT=?
1. Design an inverting amplifier with a gain of 4. Use an ideal op amp, a 30 kΩ resistor in the feedback path, and ±12 V power supplies. 2. Using your design from part (a), determine the range of input voltages that will keep the op amp in its linear operating region. 3. Suppose you wish to amplify a 2 V signal, using your design from part (a) with a variable feedback resistor. What is the largest value of feedback resistance that keeps the op amp in its linear operation region? Using this resistor value, what is the new gain of the inverting amplifier?