Operational amplifier (Op-Amp) Exercise In a certain application, produces a 1 mlme signal. This signal must be amplified to 4 Krms- Assuming that the phase of the load voltage is in phase with input signal. design an operational amplifier circuit for the application. Hint: Choose, arhitrrily, imput resistor, R = 200kn and find feedhack rexistor, Ry.

Operational amplifier (Op-Amp) Exercise In a certain application, produces a 1 mlme signal. This signal must be amplified to 4 Krms- Assuming that the phase of the load voltage is in phase with input signal. design an operational amplifier circuit for the application. Hint: Choose, arhitrrily, imput resistor, R = 200kn and find feedhack rexistor, Ry.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The circuit is a current regulator utilizing an ideal op amp. (a) Find the current in theZener diode and the drain current in the NMOStransistor if the Zener voltage is 6.8 V. (b) Whatis the op amp output voltage if the MOSFET hasVTN = 1.25 V and Kn = 75 mA/V2?
Determine the output voltage of an op-amp forinput voltages of Vi1=150μV, Vi2=140μV and CMRRs of100 and 105. (Given Ad =4000) Vd=? Vc=?
Suppose the op amp shown has an fT of 3 MHz. What is the phase margin of the ampliﬁer?
In an op-amp having specified signal bandwidth of 1 MHz and closed loop gain of ACL=200 V/mV, find the cutoff frequency.
For the circuit shown below, if the differential gain (?? ) of the op-amp is (50000) and the CMRR in (db) is (34). Find the output voltage (v_out).
The open-loop gain A of real (nonideal) op-amps isvery large at low frequencies but decreases markedlyas frequency increases. As a result, the closed-loopgain of op-amp circuits can be strongly dependent on frequency. Determine the relationship between a finiteand frequency-dependent open-loop gain AV(OL)(ω)and the closed-loop gain AV(CL)(ω) of an invertingamplifier as a function of frequency. Plot AV(CL)versus ω. Notice that −RF/RS is the low-frequencyclosed-loop gain.
What is the output impedance of an Ideal Operation Amplifier? What is the open loop gain of an Ideal Operation Amplifier? What is the gain of a voltage follower operational amplifier circuit? What is the input impedance of this circuit? Draw the circuit. How can I add two voltages values together with on op amp? Using op amps, how to make an AD Converter? A DA Converter? What components determine the frequency of an astable, 555 oscillator? Draw the circuit. Draw a circuit for both an astable and a monostable, 555 multivibrator. What is the duty cycle and percentage duty cycle of a pulse train or square wave? What is the overshoot, rise time, fall time, and pulse width of a pulse and where on the waveform is each measured?
Given a inverting op-amp with Vin= 1Vpk,1kHz and Rin=1kΩ , Rf=10kΩ, VEE=-5V, VCC= 5V, Explain the output waveform shown below.
It is known that IDSS = 14 mA, VP = -8 V, VGSQ = -3.2 V, RG = 1 MΩ and RS = 0.32 kΩ in the circuit in the figure. Accordingly, what is the value of the output impedance of the circuit (Z0)? NOTE: The FET output resistance is rd = 20 kΩ and will be taken into account in the calculations.
a) Construct nyquist curves for K=1, 5/3, 9 values. Write down the Nyquist stability criterion and explain whether the system is stable or not. b) Define the gain and phase margin, this time on the nyquist curve.
Draw the AC equivalent circuit and find Zi, Zo, Av, Ai (ignore the effect of To). Show all the necessary derivations and label all the parameters properly.
An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.