4) The C83400 red brass rod AB and 2014-T6 aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when the temperature is 50°F, determine the average normal stress in each member when the temperature is 120°F. Also, how far will the collar B be dis- placed? The cross-sectional area of each member is 1.75 in2. B -3 ft- 2 ft

4) The C83400 red brass rod AB and 2014-T6 aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when the temperature is 50°F, determine the average normal stress in each member when the temperature is 120°F. Also, how far will the collar B be dis- placed? The cross-sectional area of each member is 1.75 in2. B -3 ft- 2 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the allowable tensile stress for the bar is 1st2allow = 21 ksi, and the allowable shear stress for the pin is tallow = 12 ksi, determine the diameter of the pin so that the load P will be a maximum. What is this load? Assumethe hole in the bar has the same diameter d as the pin. Take t = 1 4 in. and w = 2 in.
The strut is supported by a pin at C and an A-36 steel (Young’s Modulus is 200 GPa) guy wire AB. If the wire has a diameter of 5 mm, determine how much it stretches when the distributed load acts on the strut. W0=11Kn/m
Rod BD is made of steel (E = 29 × 106 psi) and is used to brace the axially compressed member ABC. The maximum force that can be developed in member BD is 0.02P. If the stress must not exceed 18 ksi and the maximum change in length of BD must not exceed 0.001 times the length of ABC, determine the smallest-diameter rod that can be used for member BD. Take P = 148 kips.The smallest-diameter rod that can be used for member BD is in.
A stainless steel tube with an outside diameter of 50 mm and a wall thickness of 5 mm is used as a compression member. If the axial stress in the member must be limited to 384 MPa, determine the maximum load P that the member can support.
A column has an outside diameter, D = 550 mm, an inner diameter, d = 150 mm.Determine the average normal stress developed on the cross section if the load, F is1890 kN.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
The center post B of the assembly has an original length of 122 mm, whereas posts A and C have a length of 126 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress (in MPa) post A. The posts are made of aluminum and have a cross-sectional area of 403 mm2. Ealuminum = 70 GPa. The correct answer is 887.66682. Show solution pls.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (sY)st = 640 MPa, and for the bronze (sY)br = 520 MPa,determine the magnitude of the largest elastic load P that can be applied to the assembly. Est = 200 GPa, Ebr = 100 GPa.
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 12 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 95 MPa, and the bearing stress between the rod head and the support plate cannot exceed 135 MPa. Determine the maximum value of Pmax that can be supported by the structure.
The assembly consists of two A992 steel bolts AB and EF and an 6061-T6 aluminum rod CD. When the temperature is at 30° C, the gap between the rod and rigid member AE is 0.1 mm. Determine the normal stress developed in the bolts and the rod if the temperature rises to 130° C. Assume BF is also rigid.
The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises after a load W = 120 kN is applied. Determine the stress at the bronze rod in MPa when there is a temperature rise of ΔT = 38 °C.
The vertical steel rod has a constant diameter of 32 mm and a length of 400 mm. is hanged from a rigid fixing. A mass is gently placed onto a collar which is attached to the lower end of the rod. The strain energy stored in the steel is 0.400 x 10-³. If Esteet = 209 GPa, 1.1 Determine the gradually applied load and magnitude of the mass. 1.2 Calculate the maximum stress in the rod when gradually applied. 1.3 Determine the magnitude of the mass when the mass is suddenly applied. 1.4 Calculate the extension of the rod when suddenly applied.