Q54. A 1:10 scale model of a submarine movingfar below the surface of water is tested in awater tunnel. If the speed of the prototype is 8m/s, determine the corresponding velocity ofwater in the tunnel. Also determine the ratio1.121 x 10 m²/s, Ywater =1.00 × 10 m²/s,of the drag for the model and the prototype.= 1.00 x 10 m²/s,= 1000 kg/m.= 1.121 x 10-6 m²/s, yYsea waterwaterPsea water= 1027 Kg/m, Pwater%3D

Answered: Image /qna-images/answer/7724788a-ed40-4a1a-8d74-0f8b1e425a14.jpg

4. A 1:10 scale model of a submarine moving far below the surface of water is tested in a water tunnel. If the speed of the prototype is 8 m/s, determine the corresponding velocity or water in the tunnel. Also determine the raio of the drag for the model and the prototype. = 1.121 x 106 m²/s, Ywater = 1027 Kg/m, Pwa = 1.00 x 10 m²/s, = 1000 kg/m2. Ysea water %3D Psea water water

4. A 1:10 scale model of a submarine moving far below the surface of water is tested in a water tunnel. If the speed of the prototype is 8 m/s, determine the corresponding velocity or water in the tunnel. Also determine the raio of the drag for the model and the prototype. = 1.121 x 106 m²/s, Ywater = 1027 Kg/m, Pwa = 1.00 x 10 m²/s, = 1000 kg/m2. Ysea water %3D Psea water water

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An square open tank with base length of 1.8 meters contains 0.9 m of water. It is translated horizontally to the right with an acceleration of 4 m/s^2. (a) How high should the tank be so that no water will be spilled? (b) If acceleration is increased to 7 m/s^2, how much water will be retained?
An open vessel 4.0m wide, 5.0m long and 3.5m deep contains 3m of water. It is then accelerated to the right along its width. a. Calculate the acceleration just about water to spill. b. At this rate, what is the force (in N) causing the acceleration if the mass of the vessel if the mass of the vessel is 600kg? c. Consider the same vessel accelerated at 7.00 m/s2. Determine the volume (in m3) of water spilled at that acceleration.
A 29.21 kg-crate travels down the path as shown below. Determine the magnitude of the work done (J) by the friction force if the crate has a speed of 91.44 cm/s at point A and has a speed of 7620 mm/s at point B. Solve and explain
As Figure Shown, Find The Head Loss Between A And B If The Velocity Is 25 m/s.
An open rectangular tank mounted on a truck is 5m long, 2m wide and 2.5m high is filled with water to a depth of 2m. (a) What is the maximum horizontal acceleration can be imposed on tank without spilling any water and (b) determine the accelerating force on the liquid mass? (c) If the acceleration is increased to 6 m/s2, how much water is spilled out?
The 50 kg crate shown in the figure rests on a horizontal surface for which thecoefficient of kinetic friction is ??=0.3 If the crate is subjected to a 400 Ntowing force as shown, determine the velocity of the crate in 3? starting fromrest
A vertical pipe is shown in figure 1 below. The pipe tapers from 50 mm in diameter to 25 mm in diameter. If 2 liters of water per minute flow upwards through the pipe the pressure difference across the pipe is 35 kpa. Calculate the flow downwards through the pipe if the pressure across the pipe is to be zero. The losses across the pipe are given by h1=k((v2) ²-(v1)²)/2g,where v1 and v2 are the velocities in the 50 mm and 25 mm sections respectively.
An open horizontal tank 2 m high, 2 m wide and 4m. long is full of water. a) How much water is spilled out when the tank is accelerated horizontally at 2.45 misec in a direction parallel with its longest side? b.) What is the porce acting on the side with the greatest depth? c.) Compute the required accelerating force.
show the complete solution. If block B moves downward with an A acceleration of 0.2 m/s 2, find the acceleration of block A
1. A rectangular channel has a contraction that smoothly changes the width to a minimum width of 1.5 f t (the throat). If the flow is critical at the throat, find the volume flow rate when the depth at the throat is 1.5 f t. 2. Water in an open channel of constant width flows over a bump of height 1 f t, as shown in Figure P10.10. What is the depth of the water Y2? Assume uniform flow of constant width with no losses.
A 100-Kg block is being pulled up a slope by an electric motor as shown. Determine the power required to move the the block at a constant speed of 1.5 m/s. The coefficient of friction between the block and the inclined surface is 0.30.
The water flows from the pipe shown in the figure with a flow rate of 0.025 m3 / s and emerges into the atmosphere as a free jet. Flow is frictionless and gravity effects are negligible. Since the pressure in the section (1) is 150kpa, find the x and y components of the force required to hold the pipe in place. [rsu = 999 kg / m3]