4. A diesel engine with the following specifications, 12 cylinders, 0.75 m x 0.95 m, four stroke cycle has a fuel consumption 0.75 kg/kW-hr based on 15,500 kJ/kg. Engine speed is 375 rpm with an indicated mean effective pressure of 20.5 bar. If the jacket water carries away an estimated 32% of the heat supplied, find its capacity in cubic meter per second required if the allowable rise is 150°C.

4. A diesel engine with the following specifications, 12 cylinders, 0.75 m x 0.95 m, four stroke cycle has a fuel consumption 0.75 kg/kW-hr based on 15,500 kJ/kg. Engine speed is 375 rpm with an indicated mean effective pressure of 20.5 bar. If the jacket water carries away an estimated 32% of the heat supplied, find its capacity in cubic meter per second required if the allowable rise is 150°C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given a Brayton cycle, with a pressure ratio equivalent to 12, as shown in the figure, determine its thermal efficiency, in %. Use Standard Cold Air Assumption Method (constant specific heats at room temperature, 25ºC).
The world’s largest diesel engine has displacement of 25 m3 running at 300 RPM in a two-stroke cycle producing 100 000 hp. Assume an inlet state of 300 kPa, 300 K and a compression ratio of 20:1. a)What is the mean effective pressure? b)The flow of air to the engine?
A Brayton cycle with an air inlet temperature of 17 °C has a pressure ratio of 16. While the cycle produces 14 MW of energy, there is an input of 960 kJ/kg 1 heat into the cycle. Recognizing that specific heats change with temperature; a) Find the highest temperature (K) of the cycle. b) Find the compressor work (kJ/kg). c) Find the turbine work (kJ/kg). d) Find the mass flow rate (kg/s) of the air. e) Calculate the thermal efficiency of the cycle.
A steam power plant operates between a boiler pressure of 52 bar and a condenser pressure of 0.045 bar. Calculate for these limits the cycle efficiency for a Rankine cycle with dry saturated steam at entry to the turbine. NB:Answer in decimal and not percentage to 4 decimal places.
An ideal Diesel engine operates on 1.5 lb of air with a suction state at 14.1 psia and 100 F. The pressure at the end of compression is 475 psia and the cut -off is 6% of the stroke from head -end dead - center. Using air properties (R=53.34 ft-lbf/Ibm-R, k=1.4, Cp =.24, Cv=. 1714 Btu/lbm-R), determine compression ratio, percentage clearance, Qa, Qr, Thermal Efficiency, mean effective pressure.
A turbo-charged, 16 cylinder, Vee-type diesel engine has an air consumption 0f 3,000 kg/hr per cylinder at rated load and speed. This air is drawn in through a filter by a centrifugal compressor directly connected to the exhaust gas turbine. The temperature of the air from the compressor is 145°C before it goes to the engine suction header. Cooling water enters air cooler at 30°C and leaves at 38°C. Calculate the Arithmetic Mean Temperature Difference (AMTD). Show your complete solution.
From a Brayton cycle, the air entering the compressor has a temperature of 300 K, a pressure of 100 kPa and an air flow rate of 6 kg/s. The compressor pressure ratio is 10. The temperature of the working fluid entering the turbine is 1400 K. The efficiency of the turbine and compressor is 80% and the efficiency of the regenerator is 80%. Calculate A. thermal efficiency, B. workback ratio, C. power produced
Problem 1: Find and compare the efficiency of the simple ideal Rankine cycle engine operating between20 and 100 deg. C for working fluids of water and Refrigerant 12. Compare the results to the Carnotefficiency.Problem 2: A Rankine cycle operates with steam under the same conditions as in Problem 1. The turbinehas an efficiency of 70 percent, and the pump efficiency is 60 percent. Find the cycle efficiency, andsketch the T-s and h-s diagrams.
A Brayton cycle with an air inlet temperature of 17 °C has a pressure ratio of 16. While the cycle produces 14 MW of energy, there is an input of 960 kJ/kg 1 heat into the cycle. Recognizing that specific heats change with temperature; c) Find the turbine work (kJ/kg). d) Find the mass flow rate (kg/s) of the air. e) Calculate the thermal efficiency of the cycle.
The piston diameter of a 4-cylinder Otto engine is 100 mm and the piston stroke is 90 mm. The compression ratio of this Otto engine, which has a compression ratio of 8 and operates according to the standard air acceptance, is 300K and its pressure is 1 bar. A)Find the thermal efficiency and the average effective pressure of the cycle.
What is the highest temperature attainable of an otto cycle engine that have compression ratioof 15, the energy input from fuel is 500 kilojoules per kilogram and it operates at an ambient airtemperature of 25 degrees Celsius.
A turboprop aircraft propulsion engine operates where the air is at 8 psia and −10°F, on an aircraft flying at a speed of 600 ft/s. The Brayton cycle pressure ratio is 10, and the air temperature at the turbine inlet is 940°F. The propeller diameter is 10 ft and the mass flow rate through the propeller is 20 times that through the compressor. Determine the thrust force generated by this propulsion system. Assume ideal operation for all components and constant specific heats at room temperature.