GIVEN: Uniform slender bar AB is 0.90 m long, has a mass of 7.50 kg, hangs from Pin A, making an angle of 8=30". A vertical force of 25.0 N is being applied 0.60 m along the bar from Pin A. At the instant shown the angular velocity of the bar is 0.5 rad/s CW. REQ'D: For the instant shown, determine: (a) the angular acceleration of the bar a; and (b) the magnitude of the total force at Pin A. 0.5 rad/s Ꮎ Horizontal 900 mm F 0.90m lang m: 7.50x4 G= 30° F= 25.0N DB di 0.60m wir.sradis cw

GIVEN: Uniform slender bar AB is 0.90 m long, has a mass of 7.50 kg, hangs from Pin A, making an angle of 8=30". A vertical force of 25.0 N is being applied 0.60 m along the bar from Pin A. At the instant shown the angular velocity of the bar is 0.5 rad/s CW. REQ'D: For the instant shown, determine: (a) the angular acceleration of the bar a; and (b) the magnitude of the total force at Pin A. 0.5 rad/s Ꮎ Horizontal 900 mm F 0.90m lang m: 7.50x4 G= 30° F= 25.0N DB di 0.60m wir.sradis cw

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The wheel W of radius R = 1.4 m rolls without slip on a horizontal surface.A bar AB of length L = 3.7 m is pin-connected to the center of the wheel and to a sliderA constrained to move along a vertical guide. Point C is the bar’s midpoint. Determinethe general relation expressing the acceleration of the slider A as a function of θ, L, R,the angular velocity of the wheel αW , and the angular acceleration of the wheel ωW .
Two uniform cylinders, each of weight W = 14 lb and radius r = 5 in., are connected by a belt as shown. Knowing that at the instant shown the angular velocity of cylinder B is 30 rad/s clockwise, determine (a) the distance through which cylinder A will rise before the angular velocity of cylinder B is reduced to 5 rad/s, (b ) the tension in the portion of belt connecting the two cylinders.
A shaft carries four masses, B, C, and D of magnitude 200 kg, 300 kg, 400 kg, and 200 kg respectively and revolving at radii 80 mm, 70 mm, 60 mm, and 80 mm in planes measured from A at 300 mm, 400 mm and 700 mm. The angles between the cranks measured anticlockwise are A to B 45º, B to C 70º, and C to D 120º. the balancing masses are to be placed in planes X and Y. The distance between the planes A and X is 100 mm, between X and Y is 400 mm and between Y and D is 200 mm. If the balancing masses revolve at a radius of 100 mm, find their magnitude and angular positions.
A small 2-kg sphere B is attached to the bar AB of negligible mass that is supported at A by a pin and bracket and connected at C to a moving support D by means of a spring of constant k = 3.6 kN/m. Knowing that support D undergoes a vertical displacement δ= δm sin wf t where δm = 3 mm and ωf = 15 rad/s, determine (a ) the magnitude of the maximum angular velocity of bar AB (b) the magnitude of the maximum acceleration of sphere B.
The connecting rod of a horizontal reciprocating engine is 400 mm and length of the stroke is 200mm. The mass of the reciprocating parts is 125 kg and that the connecting rod is 100 kg. The radius of gyration of the connecting rod about an axis through the centre of gravity is 120 mm and the distance of centre of gravity of the connecting rod from big end centre is 160 mm. The engine runs at750 r.p.m. Determine graphically the torque exerted on the crankshaft when the crank has turned 30° from the inner dead centre.
Two uniform cylinders, each of mass m = 6 kg and radius r = 125 mm, are connected by a belt as shown. Knowing that at the instant shown the angular velocity of cylinder A is 30 rad/s counterclockwise, determine (a) the time required for the angular velocity of cylinder A to be reduced to 5 rad/s, (b) the tension in the portion of belt connecting the two cylinders.
A 2.5-kg homogeneous disk of radius 80 mm rotates at the constant rate ω1 = 50 rad/s with respect to arm ABC, which is welded to a shaft DCE. Knowing that at the instant shown, shaft DCE has an angular velocity w2 = (12 rad/s)k and an angular acceleration a2= = (8 rad/s2)k, determine (a) the couple that must be applied to shaft DCE to produce that acceleration, (b) the corresponding dynamic reactions at D and E.
The 250 g disk shown spins at the rate w1 = 750 rpm, while axle AB rotates as shown with an angular velocity ω2 of 6 rad/s. Determine the Kinetic energy of the disk.
A slender rod is bent to form a square frame of side 6 in. The frame is attached by a collar at A to a vertical shaft that rotates with a constant angular velocity w. Determine the value of w for which line AB forms an angle β = 48° with the horizontal axis.
A semicircular panel with a radius r is attached with hinges to a circular plate with a radius r and initially is held in the vertical position as shown. The plate and the panel are made of the same material and have the same thickness. Knowing that the entire assembly is rotating freely with an initial angular velocity of w0 , determine the angular velocity of the assembly after the panel has been released and comes to rest against the plate.
The mechanism shown is composed of rod GPV pin-connected to rod DPE at point P. Knowing that the velocity of V is 4 m/s downwards, A. [20%] Redraw bar GPV and determine its instantaneous center of rotation (label it as point C). Specify all angles and distances needed. B. [15%] Determine the angular velocity of rod GPV. C. [30%] Determine the velocity of point P. D. [20%] Redraw bar DPE and determine its instantaneous center of rotation (label it as point C). Specify all angles and distances needed. E. [15%] Determine the angular velocity of rod DPE. NOTE: Use INSTANTANEOUS CENTER METHOD for Velocity Analysis
A 1.6-kg tube AB can slide freely on rod DE which in turn can rotate freely in a horizontal plane. Initially the assembly is rotating with an angular velocity of magnitude w = 5 rad/s and the tube is held in position by a cord. The moment of inertia of the rod and bracket about the vertical axis of rotation is 0.30 kg.m2 and the centroidal moment of inertia of the tube about a vertical axis is 0.0025 kg.m2If the cord suddenly breaks, determine (a) the angular velocity of the assembly after the tube has moved to end E, (b) the energy lost during the plastic impact at E.