4. A partially open pressure relief valve discharges 160°F system oil with a Sg of 0.91 at 5 gal/min into the reservoir with a pressure drop of 800 lbf/in². What will be the temperature of the oil as it flows into the reservoir? The specific heat of the oil is 0.42 Btu/lbm/°F.

4. A partially open pressure relief valve discharges 160°F system oil with a Sg of 0.91 at 5 gal/min into the reservoir with a pressure drop of 800 lbf/in². What will be the temperature of the oil as it flows into the reservoir? The specific heat of the oil is 0.42 Btu/lbm/°F.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

How high must the pump centerline be located above the water level in an open tank that supplies water to the pump if it requires a minimum of 2.5m of NPSH? The barometer reading is 760mmHg, the pipe friction is 0.65m and the vapor pressure is 3.51kPa. 6.82m 5.48m 7.39m 4.99m
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. i. Determine Delta Z (Z2 - Z1) in ft. ii. What is the actual shaft work needed for this particular mass flow rate in (ft-lbf)/s. iii. What is the mass flow rate of the water in lbm/s?
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. answer the ff: i. Determine the velocity of the water at point 2. ii. Reynolds number for the flow. iii. A pump efficiency of 55% means that the theoretical work needed for the process is 55% of the actual work needed. In other words, 55% more shaft work is necessary. Determine the theoretical shaft work required in foot-pound force per pound mass.
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. i.Let us set our first point at the surface of the large reservoir, and the second point at the surface of the open elevated tank. Determine the velocity of the water at point 1 in ft/s. ii.What is the density of water at the conditions stated in lb/ft3? iii.If 1 horsepower is equivalent to 500 (ft-lbf)/s, the pump should be able to supply how much hp?
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. a. Assuming that the large open reservoir is open to the atmosphere as well, what is the mechanical energy balance eq for the system? b. What is the Reynolds number for the flow ?
A pump takes in oil at a temperature of 400oF from a closed tank in which the pressure is 85 psig. The specific gravity of oil 0.78 and its vapor pressure is 100 psia. The loss in the suction pipe is 2ft and the pump is located 12 ft below the oil level in a plant at sea level. Will there be cavitation in the pump? If so, how can this be corrected?
A pump is to deliver 80 gpm of water at 140°F with a discharge pressure of 150 psig. Suction pressure indicates 2 inches of mercury vacuum. The diameter of suction and discharge pipes are 5 inches, respectively. The pump has an efficiency of 70%, while the motor efficiency is 80%. Determine power input to the drive motor.
The power requirement of a 3-stage compressor (in kW, two decimal places) in order to supply air at 20 degrees celcius at a rate of 250 cubic meter per hour at a total discharge pressure of 100 psig is ___________. If the efficiency of the compressor is 60%. Give full solution:
In a water tank, the water level is 20m above ground. A hose is connected to the tank's bottom and the nozzle on the end of the hose is pointing straight up. The stream from the nozzle is 25m above the ground. What may cause the water from the hose to rise above the tank level?
If a pump requires a minimum of 2.75 m of NPSHA, how high can the centerline of the pump be located above the top of an open tank that supplies 27 C water to the pump? The barometer reads an average of 732 mmHg throughout the year. The tank is 1.82 m high. The pipe friction is 0.7 m and the velocity is 1.22 ?/? .
5. Oil of specific gravity 0.750 is pumped from a tank over a hill through a 24′′ pipe with the pressure at the top of the hill maintained at 25.5 psi. The summit is 250 ft above the surface of the oil in the tank, and oil is pumped at the rate of 22.0 cfs. If the lost head from tank to summit is 15.7 ft, what horsepower must the pump supply to the liquid? indicate free body diagram
In the system, 900 L/min of oil is pumped with (s=0.92), from an underground storage tank to the first stage of a processing system. If the loss in the suction line is 1.5m and the loss in the discharge line is 4.5m. The suction line is 2.5” and the discharge line is 1.5”. Determine a) the outlet pressure in psi of the pump. b) The power in hp of the pump