Kindly answer with complete solution please.Subject: Fluid Mechanic 4. A Pelton turbineproduces 8 MW of powerunder net head of 440 m.The turbine has two jets.The buckets deflect thejet by an angle of 165°. Ifthe bucket frictioncoefficient is 0.85,compute the following:(a) Discharge(b) Diameter of each jet(c) The total forceexerted by the jets on thewheel in the tangentialdirection(d) Power produced bythe runner(e) Hydraulic efficiencyThe overall efficiency,coefficient of velocity andspeed ratio may beassumed0.85, 0.98, and 0.47,respectively.

Answered: Image /qna-images/answer/104ab00a-8a95-42dd-8539-868a263b479c.jpg

4. A Pelton turbine produces 8 MW of power under net head of 440 m. The turbine has two jets. The buckets deflect the jet by an angle of 165°. If the bucket friction coefficient is 0.85, compute the following:

4. A Pelton turbine produces 8 MW of power under net head of 440 m. The turbine has two jets. The buckets deflect the jet by an angle of 165°. If the bucket friction coefficient is 0.85, compute the following:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A plant has installed a single suction centrifugal pump with a discharge of 68 m3/hr under 60 m head and running at 1200 rpm. It is proposed to install another pump with double suction but of the same type to operate at 37.22 m head and deliver 90 m3/hr. Determine the speed of the new pump. and what should be the new impeller diameter if the diameter of the original pump is 140mm?
The MITL ME laboratory has installed a double-suction, three-stage, centrifugalpump with a discharge of 330 gpm under 200 ft head and running at 1200 rpm. It isproposed to install another pump with double suction and six stages, but of the samecharacteristics, to operate at 98 ft head and deliver 430 gpm. Calculate a) the speed ofthe proposed pump; b) the impeller diameter of the proposed pump if the diameter of theexisting pump is 6 inches; and c) the type of the existing and the proposed pump.
While rotating at 900 rpm, a centrifugal pump delivers 2500 gpm of water at ahead of 75 ft. If the impeller diameter is 1.5 ft. and the blade width is 1.75 in.,find the (a) blade angle β2, (b) radial velocity Vr2, and (c) blade speed u2. Assumeno whirl at the inlet.Ans: β2=12.5°; Vr2=8.1 ft./s; u2=70.7 ft./s
The manometric head developed by a three-stage centrifugal pump runningat 450 rpm is 60 m. The width and diameter of each impeller at the outlet are60 mm and 750 mm, respectively, with outlet blade angle 45°. Determine itsmanometric efficiency, if discharge through the pump is 0.3 m^3/s.
A Pelton wheel works at the foot of a dam because of which the head available at the nozzle is 400 m. The nozzle diameter is 160 mm and the coefficient of velocity is 0.98, The diameter of the wheel bucket circle is 1.75 m and the buckets deflect the jet by 150°. The wheel-to-jet speed ratio is 0.45. Neglecting riction, calculate (1) the power developed by the turbine, (i) its speed and (i) hydraulic efficiency.
A multi-jet Pelton turbine with a wheel 1.47 m diameter, operates under an effective head of 200 m at nozzle inlet and uses 4 m3/s of water. Tests have proved that the wheel efficiency is 88 per cent and the velocity coefficient of each nozzle is 0.99. Assuming that the turbine operates at a blade speed to jet speed ratio of 0.47, determine:(1) the wheel rotational speed;(2) the power output and the power specific speed;(3) the bucket friction coefficient given that the relative flow is deflected 165°;(4) the required number of nozzles if the ratio of the jet diameter to mean diameter of the wheel is limited to a maximum value of 0.113.
A centrifugal pump with impeller diameter 500mm is designed for a discharge of 1.0m3/s of water. The water enters the pump axially, leaving the impeller with an absolute velocity of 12m/s at an angle of 20degrees to the tangent at the impeller periphery. The impeller is rotating at 700rpm. Determine the exit vane angle and the hydraulic power delivered.
It is desired to construct a hydraulic turbine for a hydraulic power plant to operate under the following conditions: discharge Q = 3.5 m3/s of water, the available net head = 290 meters, the hydraulic efficiency = 0.8, the rotating speed = 300 rpm. A Pelton wheel impulse turbine was selected with the following specifications: the bucket angle b2 = 160°, the coefficient of velocity for the nozzle is 0.98 and assume the friction coefficient k = 0.2. Determine the following:Jet Diameter to Wheel diameter ratio, dj/Dw. The Specific Speed in M.K.S., Ns.The computed head coefficient ϕ.The brake horsepower. The required number of Jets. The Pelton wheel diameter in meters.
Fluid Mechanics. Reg.no : 5395 Pb # 6: At its optimum point of operation, a given centrifugal pump with an impeller diameter of 500 mm delivers a 4 m3/s of water against a head of (Reg.No/100) m when rotating at 1500 rpm. (a) If its efficiency is 82%, what is the brake power of the drive shaft? (b) If a homologous pump with a diameter of 800 mm is rotating at 1200 rpm, what would be the discharge, head, and shaft power. Assume both operate at the same efficiency. (c) Compute the specific speed of both pumps. What type of pumps are these?
A volute centrifugal pump with an impeller diameter of 0.02 m has the following performance data when pumping water at the best efficiency point: impeller speed N = 58.3 revs/s capacity Q = 0.012 m3/s total head Ah = 70m required net positive suction head NPSH = 18m brake power Pe = 12000w Determine the new performance data (listed above) of a homologous pump with twice the impeller diameter operating at half the impeller speedand same efficiency.
A 5 MW turbine is developed under an effective head of 320 m. The turbine efficiency is85%. Velocity coefficient of the nozzle is 99%.(a)Select which is the appropriate turbine based on effective head. (b)What should be the wheel diameter in meters assuming it is 12 times the diameter of the jet?
[5] A Francis turbine operates at its maximum efficiency point at h0 = 0.94, corresponding to a power specific speed of 0.9 rad. The effective head across the turbine is 160 m and the speed required for electrical generation is 750 rev/min. The runner tip speed is 0.7 times the spouting velocity, the absolute flow angle at runner entry is 70 deg from the radial direction and the absolute flow at runner exit is without swirl. Assuming there are no losses in the guide vanes and the mechanical efficiency is 100%, determine (i) the turbine power and the volume flow rate; (ii) the runner diameter; (iii) the magnitude of the tangential component of the absolute velocity at runner inlet; (iv) the axial length of the runner vanes at inlet.