A steam power plant operates on a Rankine cycle. Steam enters the turbine at 600 F and 15 MaP and exits the turbine at 15 kPa. The turbine isentropic efficiency is 88%. The pump has an isentropic efficiency of 92%. The steam flow rate into the turbine is 200kg/s. What is the turbine outlet temperature, the turbine outlet quality, the turbine outlet enthalpy, the turbine outlet entropy, the turbine output power, the pump input power, the rate of heat input, and the cycle thermodynamic efficiency. Show the process on a T-s Diagram.

A steam power plant operates on a Rankine cycle. Steam enters the turbine at 600 F and 15 MaP and exits the turbine at 15 kPa. The turbine isentropic efficiency is 88%. The pump has an isentropic efficiency of 92%. The steam flow rate into the turbine is 200kg/s. What is the turbine outlet temperature, the turbine outlet quality, the turbine outlet enthalpy, the turbine outlet entropy, the turbine output power, the pump input power, the rate of heat input, and the cycle thermodynamic efficiency. Show the process on a T-s Diagram.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A power plant operating on a Rankine cycle has steam entering the turbine at 500 °C and 2 MPa. The turbine and pump efficiencies are 85 and 90 percent, respectively. If the water enters the pump at 10 kPa at a rate of 162,000 kg/hr, calculate the (a) actual turbine power, (b) actual pump power, (c) actual heat added to the water in the boiler, (d) actual cycle thermal efficiency, and (e) actual condition of steam leaving the turbine.
A steam power plant operates on a simple ideal Rankine cycle between the pressure limits of3 MPa and 50 kPa. The temperature of the steam at the turbine inlet is 300°C, and the massflow rate of steam through the cycle is 35 kg/s. Show the cycle on a T-s diagram with respectto saturation lines, and determine (a) the thermal efficiency of the cycle and (b) the net poweroutput of the power plant.
A simple power plant utilizing the Rankine Cycle operates with an inlet boiler pressureof 5 MPa and an inlet condenser pressure of 300 kPa. Because of frictional effects, thepressure of the water drops 0.3 MPa in the boiler and 3 kPa in the condenser. Thetemperature of the steam as it enters the turbine is 700 °C. The adiabatic efficiency ofthe pump and of the turbine are 83 percent and 88 percent, respectively. The pumpand the turbine are adiabatic, and the water enters the pump as saturated liquid. It canbe assumed that heat transfer to the water in the boiler is from a reservoir at 1500 K,and the environment is at 25 °C.Determine the thermal efficiency of the cycle and compare it with the thermal efficiencyof (a) a Carnot cycle, and (b) the ideal Rankine Cycle. Specify the amount of entropygenerated in each step of the real cycle
In a simple Rankine cycle, the working fluid is water, operating at pressures between 7.5 kPa and 1750 kPa. The water vapor is in the form of saturated steam at the turbine inlet. Turbine expansion andCalculate the thermal efficiency of the cycle, assuming that the compression processes in the pump are reversible adiabatic.
This is thermodynamics. Please complete solution A power plant operating on a Rankine cycle has steam entering the turbine at 500 °C and 2 MPa. The turbine and pump efficiencies are 85 and 90 percent, respectively. If the water enters the pump at 10 kPa at a rate of 162,000 kg/hr, calculate the (a) actual turbine power, (b) actual pump power, (c) actual heat added to the water in the boiler, (d) actual cycle thermal efficiency, and (e) actual condition of steam leaving the turbine.
A simple Rankine cycle has a pump with an isentropic efficiency of 70%. The inlet and outlet pressures of the turbine are 6 MPa and 0.075 MPa, respectively, and steam enters the turbine at 550°C. Determine a) the isentropic efficiency of the turbine if the quality at the turbine outlet is to be ? = 1, b) the thermal efficiency of the cycle, c) the rate of heat input into the boiler if the net power output of the cycle is 10 MW.
Air enters the compressor of a regenerative gas-turbine engine at 100 kPaand 300 K and is compressed to 800 kPa. The regenerator has aneffectiveness of 65 percent, and the air enters the turbine at 1200 K. For acompressor efficiency of 75 percent and a turbine efficiency of 86 percent,determine(a) The heat transfer in the regenerator.(b) The back work ratio.(c) The cycle thermal efficiency
A power plant operating on an ideal Rankine cycle has steam entering theturbine at 500°C and 2 MPa. If the steam enters the pump at 10 kPa, calculate the thermal efficiency with pump work included, the thermal efficiency neglecting pump work, and the percentage error in efficiency neglectingpump work.
There is a simple real rankine cycle, in which the steam enters the turbine with a pressure of 5MPa and a temperature of 500°C. The working pressure of the condenser is 20kPa. The mass flow of steam 35.4 kg/s. The Isoentropic efficiency of the turbine is 88% And the isoentropic efficiencyof the pump is 84%. Determine: a) The thermal efficiency of the cycle b) The net power produced by this cycle
A Rankine Cycle operates at a throttle pressure and temperature of 5 MPa and 450°C, respectively. The generator produces 20 MW at an efficiency of 95% while the mechanical efficiency is 97%. The actual expansion efficiency of the turbine is 85% and the pressure of the condenser is 10 kPa. Determine the mass flow rate of steam in kg/s
Which is more efficient the Diesel Cycle or the Otto cycle?
A steam power plant operating on an intermediate steam Rankine cycle has an open feedwater heater. The enthalpy of the steam at the turbine inlet is 3208 kJ/kg, the enthalpy at the split point is 2648 kJ/kg, and the enthalpy at the turbine exit is 2158 kJ/kg. The net power of the power plant is 100 MW, and the mass ratio of the steam leaving the turbine in the intermediate steam intake is 0.244. What is the mass flow rate of steam at the turbine inlet if the pump work is ignored?