4. A pipe has an initial radius of 30cm, which then changes to a radius of 10cm. The velocity of the water in the initial part of the pipe is 2m/s. The segment of the pipe with the smaller radius is also 0.5 m higher than the initial pipe segment. What is the pressure difference between the two parts of the pipe? (6 pts) b) What is the volume flow rate in the pipe? (3 pts)

4. A pipe has an initial radius of 30cm, which then changes to a radius of 10cm. The velocity of the water in the initial part of the pipe is 2m/s. The segment of the pipe with the smaller radius is also 0.5 m higher than the initial pipe segment. What is the pressure difference between the two parts of the pipe? (6 pts) b) What is the volume flow rate in the pipe? (3 pts)

Name: 4. A pipe has an initial radius of 30cm, which then changes to a radi
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 4. A pipe has an initial radius of 30cm, which then changes to a radius of 10cm. The velocity of thewater in the initial part of the pipe is 2m/s. The segment of the pipe with the smaller radius isalso 0.5 m higher than the initial pipe segment. Wha

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A fully-filled open storage tower of height 32 m and diameter 3.0m supplies water to a house. A horizontal pipe at the base of the tower has a diameter of 2.54cm. To satisfy the needs of the home, the supply pipe must be able to deliver water at a rate of 0.67 gal/s. a. If water were flowing at the maximum rate, what would be the pressure in the horizontal pipe?b. A smaller pipe, of diameter 1.27 cm supplies the second floor of the house, a distance of 7.2 m above the ground level. What are the flow speed and water pressure in this pipe?
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 75 L/s, and leaves the sprinkler nozzles as 2-cm diameter jets at an angle of ? from the tangential direction, as shown. The length of each sprinkler arm is 0.52 m.For the specified flow rate, investigate the effect of discharge angle ? on the rate of rotation n. by varying ? from 0° to 90° in increments of 10°. Plot the rate of rotation versus ?, and discuss your results.
A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference betwoen the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine the anchoring force needed to hold the elbow in place A) 27 N 3433.5 N C) 79.5 N D) 132. 9 E) 106. 5 N
In our house water pipe line with diameter of 2cm is connected to shower head that has 35 holes. The speed of the water in the pipe line is 1.1m/sec. i) What is the volume flow rate in the pipe line? ii) At what speed does the water leave one of the holes with diameter 0.0014m in the shower head?
Using the situation below, how would I determine the net resultant force exerted on the reducer by the water? In this situation, water is flowing horizontally in a pipe that has a diameter of 25cm. This water is flowing at 8 m/s and at 300 kPa gage it enters a 90 degree bend reducing section. This bend reducing section is connected to a vertical pipe that has a diamater of 15cm. Moreover, the inlet of the bend is 45 cm above the exit. Here, fricition and gravity are negligible and the momentum flux correction factor is 1.04.
Water flows through a pipe of 0.0025 m^2size with a uniform velocity of 7m/s and flows out from an ariface at bottom at a rate 0.003 m^3/s. what is rate of change of mass of water in the tank?
4. Hydroelectric plants in the mountains bring water from a reservoir down to a turbine through enclosed tubes. In such plants, the 100 cm diameter intake tube (Point 2) in the dam is 50m below the water surface (Point 1) of the reservoir. The water drops 200 m through the tube before flowing into the turbine through a 50 cm diameter nozzle.
Water flows at a rate of 1.17L/s through a flanged faucet with a partially closed gate valve spigot. The inner diameter of the pipe at the location of the flange is 2cm, and the pressure at that location is measured to be 90kPa. The total mass of the faucet assembly plus the water within it is 5.7 kg. Calculate the net force on the flange.
A cubical reservoir(3.5mx3.5mx3.5m) is being filled with gasoline (SG=0.72) through section 1 with 950 litre/m and through section 2 with velocity of 5cm/s, and exit at Section 3 at 15cm/s. The diameter of the round pipe at section 2 is 35mm and section 3 is 50mm. i) Determine the rate of increment/decrement h(m/s) ii) Determine time taken to fill up the reservoir from empty, if section 3 is closed. iii) Determine the rate of increment/decrement h(m/s), if the flow at flow rate at Section 1 is halved, Section 2 changes direction, and Section 3 is closed.
A jet of water issues from a kitchen faucet and falls vertically downward at a flow rate of 34 mL/s. At the faucet,which is 35 cm above the sink bottom, the jet diameter is 1.5 cm. Determine the diameter of the jet where it strikes the sink.
Water flows through a 2.5 cm pipe at115 L/minand o.15 bar pressure. It vents vertically 1 mabove the pipe. How high will the water shootfrom the vent?
1. Water flows through a venturi meter. At the constricted section where the area is 24cm², the pressure is 10.2N/cm², and at the section where the area is 64cm², the pressure is 18.0N/cm². Determine the velocities of water in the larger and smaller pipes and the rate of flow. 2. Why is a water tower generally placed on top of a hill? If the hill is 50m high, can it supply water to the top of a 100-m tal officebbuilding? If not, how does water get to that floor?.