4. A solid truncated conical bar of circular cross section tapers uniformly from a diameter d2 at its small end to dị at the large end. The length of the bar is L. Determine the elongation due to an axial force P applied at each end as shown.

4. A solid truncated conical bar of circular cross section tapers uniformly from a diameter d2 at its small end to dị at the large end. The length of the bar is L. Determine the elongation due to an axial force P applied at each end as shown.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.3P

See similar textbooks

Related questions

Q: Question 4: Two wrenches are used to tighten the pipe. If the pipe is made from a material having an…

Q: Two loads P act as shown, one parallel to x and another parallel to z axes; each load P equals 1850…

Q: Rigid beam AB rests on the two short posts shown in Fig. 4–7a. AC is made of steel and has a…

Q: A circular steel tube of length L = 1.0 m is loaded by torques T a) If the inner radius of the tube…

A: a. At inner surface: from the given data, Shear strain,

Q: 2. A hollow circular shaft of inner radius 10 mm, outer radius 20 mm and length 1 m is to be used as…

Q: Two solid steel shafts of different diameters are joined together at point C. The diameter of the…

Q: A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine…

A: Given data as per question compressive load of P = 55 kips α= 30°. calculating the inclined plane…

Q: A cylindrical rod AB is made of aluminum is connected at B to a brass cylindrical rod BCD as shown…

Q: 1. The steel system consists of rod CD, rod AB and a rigid bar AC. The diameter of rods CD and AB…

Q: The solid shaft of radius r is subjected to a torque T. Determine the radius r of the inner core of…

A: given data as per the question The radius of the bar = r Torque subjected = T

Q: A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5…

A: Given data: p=5 MPar=500 mmt=10 mm Need to determine the average circumferential (hoop) stress.

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

Q: A circular bar ABC 3m long is rigidly fixed at its ends A and C shown in fig.If a moment of 680 N.m…

A: GivenLength of circular bar L=3mmoment apllied at point B M=680Nmlength of AB L1=1.8mdia ofAB…

Q: Given: 2 solid shafts of different materials are rigidly fastened together and supported as shown.…

Q: aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in ure. Axial loads…

Q: 3. The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminum…

Q: A brass bar having a cross sectional area of 500 mm2 is subjected to an axial force as shown in the…

Q: Two aluminum rods AB and BC hinged to rigid supports, are pinned together at B to carry a vertical…

A: Given data as per the question P =3000 lb cross-section area =0.5 in2 E=10×106 psi Calculations…

Q: 3.6 Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB…

A: Diameter of the steel shaft AB, D= 15 mm Maximum allowable shear force in the shaft, τ= 120 MPa…

Q: The constant wall thickness of a steel tube with the cross section shown is 2 mm. If a 600-N m…

A: Given data: d=10 mmri=9 mmt=2 mmro=11 mmT=600 N.mG=80 GPa Need to determine the shear stress in the…

Q: 3.6 Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB…

Q: A high strength drill rod used for boring a hole in the earth has a diameter of 50 mm. The allowable…

Q: H.W:The bell crank shown in Figure , is in equilibrium, a) Determine the required diameter of the…

A: Given :connecting rod=ABσxAB=100 MNm2

Q: The wrench is applied to two forces each of magnitude P. The steel shaft AB has a diameter of 15 mm.…

Q: An aluminum alloy cylindrical roller with diameter 1.25 in and length 2 in rolls on the inside of a…

Q: An impeller mechanism in a granular material mixing tank is shown. The shaft is hollow with a 2.25"…

A: Given, ro = 2.25" θmax=6o τmax=10 ksi G = 11000 ksi

Q: Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

Q: 4m solid core steel shaft with 50 mm diameter is fixed at its ends. It is subjected to a 400 N-m…

Q: 3.6 Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB…

A: Torque:

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 13…

A: For solving this problem, we have used torosion equation, answer we got after equating all the…

Q: The circular shaft shown is subjected to an axial force P at its free end and a compressive force of…

A: Answer: The maximum allowable value of load P is 11.66 kips.

Q: Q-2 A circular bar ABC 3m long is rigidly fixed at its ends A and C shown in fig .If a moment of 680…

A: Given, length of the bar , L =3 m Moment , T = 680 Nm

Q: Opposing axial torques are applied at the ends of a straight bar ABCD. Each of the parts AB, BC and…

A: Given: Straight bar ABCD, Length of Parts AB, BC, CD = 500 mm

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

A: Given data Diameter of steel shaft = 30 mmAllowable shear stress = 120 MPaAngle of twist = 7°Shear…

Q: P. Find the maximum allowable value of P (in lbs) if the working stresses are 40 ksi for steel and…

Q: For the antenna tower shown, it is supported in its upright position by four high tensile wires.…

A: Given: youngs modulus of the wire→E=200 GPa=200×103 MPa Diameter of the wire→d=12 mm so area moment…

Q: the cross-stctions e-e and f-f, respectively, when a torque T = 800 Nm is applied at point B. Take…

Q: A round shaft of diameter "d" and length "L" fixed at both ends 'A' and 'B' is subjected to twisting…

A: Write the general torsion equation. (T/J) = (τ/R) = (Gθ/L) Here, T is torque, J is polar moment of…

Q: The compound axial member shown consists of a 20-mm diameter solid aluminum [E = 70 GPa] segment…

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

Q: and (b) the ratio o 3.51 Fig. shows a circular steel bar. (a) and Fig. square st T applied to them.…

A: Given:r=aπ

Q: A 28mm diameter steel shaft AB is built into a rigid wall at A and supported by a smooth bearing at…

Q: 2 m long and (52) mm diameter aluminum shaft is to be replaced by a hollow shaft of the same length…

Q: The compound steel bar shown in Figure is made of three uniform segments marked as 1, 2 and 3 of…

A: net force acting on segment 1 : +80-40+25 kN = 65 kN

Q: shaft ABCD, 25 mm in diameter is subjected to torques of 1850 N-m at B and 2000 N-m at C acting in…

Q: 3.41 The constant wall thickness of a steel tube with the cross section shown is 2 mm. If a 600-N m…

Q: The L-shaped rigid bar shown is pin connected at C, welded to a rigid bar AB at point B, and rests…

A: Given: The shear modulus of the rubber, G = 150 MPa The thickness of rubber pads, t = 30 mm = 0.03 m…

Q: Material = 1026 DOM steel tubing. Determine: a) The maximum shear stress, T. b) The angle of twist,…

A: Note: As per the Bartleby guidelines, only three parts of a question can be answered at a time.…

Q: or section T below, subject to eccentric loads, determine: a) The position of the centroid; b) The…

A: Calculation of position of the centroid for given T section: The point O is the origin and all the…

Concept explainers

Basic Thermodynamic Processes

The word 'thermodynamics' can be divided into two words, 'thermo' and 'dynamics'. The word thermo deals with the heat and thermal phenomenon, whereas dynamics deals with forces or external agent that drives the heat flow or aids in the motion of heat.

Question

100%

Hello sir, please, the solution and the solution line is as in books, I mean, not manual, please, sir, please, the line is as in books.

4. A solid truncated conical bar of circular cross section tapers uniformly from a
diameter d2 at its small end to d, at the large end. The length of the bar is L.
Determine the elongation due to an axial force P applied at each end as shown.
Elementary Strip
dx
7-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If a 12-ft long portion of the bar in Question 23 is elongated 0.064 in. by the pull, the unit elongation in that portion is A. 0.00533 B. 0.00444 C. 0.000533 D. 0.000444
A 37.5-mm-diameter rod 6 mlong elongates 12 mm under a load 236 KN. Thediameter of the rod decreases 0.025 mm during theloading. Determine the following properties of thematerial: (a) Poisson’s ratio.(b) Young’s modulus(c) The modulus of rigidity.
The rod BD is made of material with G1= 33 GPa has a diameter 46 mm is bonded to the tube CA at point B, the tube made of material with G2=56 GPa has an outer diameter 97 mm and wall thickness of 8 mm. If T1=1268 N.m and T2=2282 N.m, answer the following questions: The polar moment of inertia of the rod BD is The polar moment of inertia of the tube CA is The maximum shear stress of the rod BD is The maximum shear stress of the tube CA is The maximum shear stress of the assembly is The angle of twist between D and B is The angle of twist between C and A is The angle of twist at D is The angle of twist between C and B is The reaction at point A is
One end of a aluminum rod of radius R = 9.4 mm and length L = 79 cm is held in a vise. A force of magnitude F = 61 kN is then applied perpendicularly to the end face (uniformly across the area) at the other end, pulling directly away from the vise. What is the elongation ΔL of the rod? The Young's modulus of aluminium is 70 x 109 N/m2.
A uniform bar of length L, cross-sectional area A, and unit mass p is suspended vertically from one end. Show that its total elongation is 8 - pgl / 2E. If the total mass of the bar is M, show also that o - MgL/2AE.
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.
The assembly below consists of a steel rod CB and an aluminium rod BA, each having a diameter of 12 mm. If the rod is subjected to the axial loadings at A and at the coupling B, determine the displacement of the coupling B and the end A. The unstretched length of each segment is shown below. Neglect the size of the connections at B and C, and assume that they are rigid. Est = 200 GPa, Eal = 70 GPa.
The bearings at A and D exert only y and z components of force on the shaft as shown in Fig 7. Determine the smallest diameter of the shaft using maximum shear stress hypothesis theory if the allowable stress is 100 MPa.
1-Determine the elongation of the steel bar 1m long and 1.5 cm cross-sectional area when subjected to a pull of 1500 kg. Take E=2*10 kg/cm ?
A solid steel post is subjected to pure torsion. Given: -post Diameter = 65 mm -length = 2.75 m -torque = 2.4 kN-m -shear Modulus of Elasticity = 78 GPa Question: What is the Polar Moment of Inertia of the Post?
The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. The image shows the cross-sectional area of the assembly .If a force P= 66 kNkN is applied to the ring F, what isthe angle of tilt of bar AC measured counterclockwise from the negative y axis.
A solid steel post having a length of 3m and a diameter of 80 mm is subjected to pure torsion. a) What is the torsional rigidity of the post if the shear modulus of elasticity is 80 GPa? b) Determine the torsional stiffness of the steel post. c) Determine the maximum shear stress in the steel post if it is subjected to a torque of 612 N-m.