Opposing axial torques are applied at the ends of a straight bar ABCD. Each of the parts AB, BC and CD is 500 mm long and has a hollow circular cross-section, the inside and outside diameters being, respectively, AB 25 mm and 60 mm, BC 25 mm and 70 mm, CD 40 mm and 70 mm. The modulus of rigidity of the material is 80 GN/m2 throughout. Calculate:(a) the maximum torque which can be applied if the maximum shear stress is not to exceed 72 MN/m2 ;(b) the maximum torque if the twist of D relative to A is not to exceed 3 degrees. *

Opposing axial torques are applied at the ends of a straight bar ABCD. Each of the parts AB, BC and CD is 500 mm long and has a hollow circular cross-section, the inside and outside diameters being, respectively, AB 25 mm and 60 mm, BC 25 mm and 70 mm, CD 40 mm and 70 mm. The modulus of rigidity of the material is 80 GN/m2 throughout. Calculate:(a) the maximum torque which can be applied if the maximum shear stress is not to exceed 72 MN/m2 ;(b) the maximum torque if the twist of D relative to A is not to exceed 3 degrees. *

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.17P: A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and...

See similar textbooks

Similar questions

A composite shaft is made by slipping a bronze tube of 3-in. outer diameteran -in. inner diameter over a solid steel shaft of the same length and 2-in.-diameter. The two components are then fastened rigidly together at their ends. What is the largest torque that can be carried by the composite shaft if the working shear stresses are 8 ksi for bronze and 12 ksi for the steel? For bronze, G = 6 x 106 psi, and for steel, G = 12 x 106 psi
A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diam-eters respectively equal to 40 and 60 mm ). (a) What is the larg-est torque that can be applied to the shaft if the shearing stress is not to exceed 120 MPa? (b) What is the corresponding minimum value of the shearing stress in the shaft?
A hollow brass alloy shaft with an outside radius of 50-mm and a wall thickness of 10-mm is subjected to a torque of T = 5.5 kN-m. Determine the minimum required diameter in mm of a solid steel shaft for which the maximum shear stress is the same?
Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm and thickness 2 mm, subjected to a torque of 92.7 N-m.
A shaft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer diameter of the shaft is 0.1 m and its wall thickness is 10 mm, what would be the minimum diameter of a solid steel shaft needed if it would be subjected to the maximum shear stress of the hollow shaft?
When a circular rod of diameter 10 cm and length 10 m is subjected to torque of 10 kN-m. Then angle of twist is _____ degree if modulus of rigidity is 100 GPa.
A flanged bolt coupling consists of eight 10 mm diameter steel bolts on a bolt circle 400 mm in diameter, and six 10 mm diameter steel bolts on a concentric bolt circle 300 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the bolts?
Pls answer thank you! A 2 in diameter 6-spline shaft ( d= 0.85D, W= 0.25D, h= 0.075D ) and to slide when not under load has a compressive force of 2500 lbs. Find the torque applied if hub length is 2 1/2 in.
A bar having a radius equal to 0.375 inches is subjected to different torques along its span as shown below. Determine the max shear stress that is experienced by the bar.
A flanged bolt coupling consists of six 10-mm diameter steel bolts on a bolt circle 300 mm in diameter and four 10 mm diameter steel bolts on a concentric bolt circle 200 mm in diameter. When torque applied is 5500 Nm, find the shearing stress (MPa), in the bolts found in the inner concentric circle. (PLEASE ANSWER IN 10 mins.)
A flanged bolt coupling consists of six 12-mm diameter steel bolts evenly spaced around a bolt circle 300 mm in diameter, and four 25-mm diameter aluminum bolts on a concentric bolt circle 200 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the steel and 40 MPa in the aluminum? Use G of ateel = 83 GPa and G for aluminum = 28 GPa
Two sections of steel drill pipe, joined by boltedflange plates at B, are being tested to assess the adequacyof both the pipes. In the test, the pipe structureis fixed at A, a concentrated torque of 500 kN ? m isapplied at x = 0.5 m, and uniformly distributed torqueintensity t0 = 250 kN . m/m is applied on pipe BC.Both pipes have the same inner diameter d = 200 mm.Pipe AB has thickness tAB =15 mm, while pipe BChas thickness tBC =12 mm. Find the maximum shearstress and maximum twist of the pipe and their locationsalong the pipe. Assume G = 75 GPa.