4. A uniform disc of mass m = 3 kg and radius R=0.5 may roll without slip on the 30 degree incline shown. An elastic spring of stiffness k = 100 newtons/meter is connected to the center C of the disc. Initially, the disc is held in place in the position shown, with the spring neither stretched nor compressed and with the disc at rest. At t = 0 the disc is released and is subjected to a constant force of Fo= 30 newtons along the incline. Determine the maximum speed achieved by the disc center C as the disc moves up the incline. For gravity use g = 10 m/sec². (note: initially the constant force Fo will be greater than the forces exerted by the spring and by gravity, and the disc will accelerate up the incline; but there will come a distance x along the incline after which the spring force + gravity will overtake the force Fo, and the disc will then decelerate). gravity → P=30 N no friction

4. A uniform disc of mass m = 3 kg and radius R=0.5 may roll without slip on the 30 degree incline shown. An elastic spring of stiffness k = 100 newtons/meter is connected to the center C of the disc. Initially, the disc is held in place in the position shown, with the spring neither stretched nor compressed and with the disc at rest. At t = 0 the disc is released and is subjected to a constant force of Fo= 30 newtons along the incline. Determine the maximum speed achieved by the disc center C as the disc moves up the incline. For gravity use g = 10 m/sec². (note: initially the constant force Fo will be greater than the forces exerted by the spring and by gravity, and the disc will accelerate up the incline; but there will come a distance x along the incline after which the spring force + gravity will overtake the force Fo, and the disc will then decelerate). gravity → P=30 N no friction

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.80P

See similar textbooks

Similar questions

The wheel in the figure has a mass of 40 kg and a radius of rotation, in relation to its center of gravity, kG = 250 mm. Whereas there is no slip, determine the work done by the weight after it rotates 90 ° clockwise from illustrated position. The AB spring has a constant stiffness k = 100 N / m and a length in the undisturbed situation of 500 mm. Consider that the wheel is initially at rest.
The wheel in the figure has a mass of 40 kg and a radius of rotation, in relation to its center of gravity, kG = 250 mm. Whereas there is no slip, determine the elastic force after it rotates 90 ° clockwise from illustrated position. The AB spring has a constant stiffness k = 100 N / m and a length in the undisturbed situation of 500 mm. Consider that the wheel is initially at rest.
Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
A baseball attachment that helps people with mobility impairments play T-ball and baseball is powered by a spring that is unstretched at position 2. The spring is attached to a cord that is fastened to point B on the 75-mm radius pulley. The pulley is fixed at point O , rotates backwards to the cocked position at 0 , and the rope wraps around the pulley and stretches the spring with a stiffness of k = 2000 N/m. The combined mass moment of inertia of all the rotating components about point O is 0.40 kg·m2. The swing is timed perfectly to strike a 145-gram baseball travelling with a speed of V0 = 10 m/s at a distance of h = 0.7 m away from point O. Knowing that the coefficient of restitution between the bat and ball is 0.59, determine the velocity of the baseball immediately after the impact. Assume that the ball is travelling primarily in the horizontal plane and that its spin is negligible.
The circular bar shown in the figure is vertical.fixed by the support at point A in the plane. AThe spring constant connected to the support is k = 40 N/m. Broadcastingundeformed length, arc between circle ABis the distance. C fitting (bracelet) with a mass of 200 grams,connected to the spring and move in a frictionless circle bar.can. When the union is θ = 30° from the rest positionis being released. In this case, relative to point B of the fittingthe highest height it can reach and the highestcalculate the speed
A uniform solid cylinder with mass M and radius 2R rests on a horizontal tabletop. A string is attached by a yoke to a frictionless axle through the center of the cylinder so that the cylinder can rotate about the axle. The string runs over a disk-shaped pulley with mass M and radius R that is mounted on a frictionless axle through its center. A block of mass M is suspended from the free end of the string (Fig.). The string doesn’t slip over the pulley surface, and the cylinder rolls without slipping on the tabletop. Find the magnitude of the acceleration of the block after the system is released from rest.
A cylinder of mass M=500kg has an axle of radius b=1m and a spool of radius R=3m. It is placed upright on a table and the string is pulled with a horizontal force F=750N to the right as shown in the figure. The cylinder is rolling without slipping and the coefficient of static friction between the cylinder and the table is µs =0.34. I = 1/2 MR^2a. Determine the linear velocity of the cylinder when it travels a distance D=2m. c. Determine the linear acceleration of the cylinder. d. Determine the friction force acting on the cylinder. e. What is the maximum pulling force, F, for which the cylinder will roll without slipping.
The slender, homogeneous rod shown in the figure below is 3 m in length and has a mass of 12 kg. At the instant shown, the rod has an angle to the horizontal of 60-degrees and an angular velocity of 2 rad/s clockwise. Both walls are smooth and provide negligible friction. At the instant shown, what are the reaction forces at A and B? What is the angular acceleration of the rod's center of mass?
The slender, uniform bar BC with a mass of 6 kg rests on the center of the 300x200 mm block of mass 3 kg. The friction coefficients at the contact points are: μA = 0.4; µB = 0.6; µC = 0 . Determine the greatest moment M that can be applied to the bar without generating movement in it.
A load of mass 230 kg is lifted by means of a rope which is wound several times round a drum and which then supports a balance mass of 140 kg. As the load rises, the balance mass falls. The drum has a diameter of 1.2 m and a radius of gyration of 530 mm and its mass is 70 kg. The frictional resistance to the movement of the load is 110 N. and that to the movement of the balance mass 90 N. The frictional torque on the drum shaft is 80 N-m. 2. Find the torque required on the drum, and also the power required, at the instant when the load has an upward velocity of 2.5 m/s and an upward acceleration of 1.2 m/s?. [Ans. 916.2 N-m ; 4.32 kW]
*********MASS IS 10 KG, NOT LBS********** The 10 kg slender bar AB, shown in the figure, has a length of 2 m. A blockof negligible mass, pinned freely to end A, is confined to move along the smooth circular groove with its centre at O. End B rests on the floor for which the coefficient of kinetic friction, µk = 0.4. If the bar is released from rest when θ = 30 degrees *********MASS IS 10 KG, NOT LBS********** a)draw the free body, kinematic and kinetic diagrams for the bar, b) set up a global reference axes system, and write down the relevantkinetic and kinematic relationships with respect to reference axes system, and c) determine the angular acceleration of the bar and the reaction forces at ends A and B. *********MASS IS 10 KG, NOT LBS**********
A man pushes bar CD to either initiate uphill motion of the homogeneous spool or to just keep the homogeneous spool from moving downhill. The spool has mass M = 88 kg. .If slippage first occurs at B, calculate the smallest force P in N that the man must apply to the bar CD to prevent the spool from moving downhill.