The double pulley shown has a mass of 15 kg and a centroidal radius of gyration of 160 mm. Cylinder A and block B are attached to cords that are wrapped on the pulleys as shown in the figure. The coefficient of kinetic friction between block B and the surface is 0.2. Consider that the system is at rest in the position shown when a constant force P= 230 N is applied to cylinder A.

The double pulley shown has a mass of 15 kg and a centroidal radius of gyration of 160 mm. Cylinder A and block B are attached to cords that are wrapped on the pulleys as shown in the figure. The coefficient of kinetic friction between block B and the surface is 0.2. Consider that the system is at rest in the position shown when a constant force P= 230 N is applied to cylinder A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The thin rod in the figure has a mass of 15kg and is attached to a spring of constant k = 50 N / m at one end, which has an unstretched length of 1.5 m. If the rod is released from rest in a horizontal position (ѳ = 0 °) and only conservative forces act on it, determine:a) What is the moment of inertia of the thin rod around the axis of rotation at A? b) What is the angle at which the rod is momentarily at rest again? c) What is the maximum angular velocity of the path?
A load of mass 230 kg is lifted by means of a rope which is wound several times round a drum and which then supports a balance mass of 140 kg. As the load rises, the balance mass falls. The drum has a diameter of 1.2 m and a radius of gyration of 530 mm and its mass is 70 kg. The frictional resistance to the movement of the load is 110 N. and that to the movement of the balance mass 90 N. The frictional torque on the drum shaft is 80 N-m. 2. Find the torque required on the drum, and also the power required, at the instant when the load has an upward velocity of 2.5 m/s and an upward acceleration of 1.2 m/s?. [Ans. 916.2 N-m ; 4.32 kW]
The thin rod of the figure has a mass of 15kg and is attached to a spring of constant K = 50 N/m at one end, which has an unstretched length of 1.5 m. If the rod is released from rest in horizontal position (ø = 0°) and only conservative forces act on it, determine: a) What is the moment of inertia of the thin rod around the axis of rotation in A? b) What is the angle at which the rod is momentarily resting again? c) What is the maximum angular speed of the route? Please attach the free body diagram if necessary. Thank you!
The 10 kg slender bar AB, shown in the figure, has a length of 2 m. A blockof negligible mass, pinned freely to end A, is confined to move along the smooth circular groove with its centre at O. End B rests on the floor for which the coefficient of kinetic friction, µk = 0.4. If the bar is released from rest when θ = 30 degrees a) draw the free body, kinematic and kinetic diagrams for the bar, b) set up a global reference axes system, and write down the relevantkinetic and kinematic relationships with respect to reference axes system, c) determine the angular acceleration of the bar and the reaction forces at ends A and B. *****MASS IS 10KGS NOT 10LBS*****
Hey, please reply as soon as POSIBLE! Wheel A, of 30kg, is located in the position shown by the effect of idler wheel D (frictionless wheel) and the system rope-spring BC. The static coefficient of friction is 0.50 and the kinetic coefficient is 0.40 between all the contact surfaces. If the force exerted by the horizontal spring is 60 N: a) Determine whether or not wheel A is turning when a moment M of 60 Nm is applied at point G. b) If it is shown that under the previous condition the wheel is turning, calculate the new value of the moment M necessary for the wheel to keep turning in equilibrium. Also indicate the frictional force that is generated at point F under that condition.
A 256-lb block is released from rest when the spring is unstretched. The drum has a weight of 76 lb and a radius of gyration of kO = 0.9 ft about its center of mass O. The coefficient of stiffness of the spring is k=78 lb/ft. The radius of the drum are: rin=0.485ft and rout=0.82ft. Find the velocity of the block after it has descended d=4 feet.
Consider the system formed by the tapered-type flywheel and the 100-kg block shown in the figure below. The block is suspended from an inextensible cord that is wrapped around a pulley of 300-mm radius rigidly attached to the flywheel. The pulley and the flywheel have a combined mass moment of inertia about its center of IT= 0.45 kg. m2. At the instant shown, the velocity of the block is 2 m/s directed downward. If the bearing at O is poorly lubricated and that the bearing friction is equivalent to a couple moment M of magnitude 80 N.m, determine the velocity of the block after it has moved 1 mdownward. Include FBD
*********MASS IS 10 KG, NOT LBS********** The 10 kg slender bar AB, shown in the figure, has a length of 2 m. A blockof negligible mass, pinned freely to end A, is confined to move along the smooth circular groove with its centre at O. End B rests on the floor for which the coefficient of kinetic friction, µk = 0.4. If the bar is released from rest when θ = 30 degrees *********MASS IS 10 KG, NOT LBS********** a)draw the free body, kinematic and kinetic diagrams for the bar, b) set up a global reference axes system, and write down the relevantkinetic and kinematic relationships with respect to reference axes system, and c) determine the angular acceleration of the bar and the reaction forces at ends A and B. *********MASS IS 10 KG, NOT LBS**********
The 13-kg sphere C is released from rest when θ = 0∘ and the tension in the spring is F = 100 N. The figure shows rod AB hinged at point A. Sphere C is attached to the other end of the rod, labeled as B. Point D is located on the rod, 0.3 meters from point A and 0.15 meters from the center of the sphere. A spring with stiffness k of 500 newtons per meter is attached to the rod at point D by one of its ends. Another end of the spring is fixed at point E, located 0.4 directly above point A. The sphere is shown to be below and to the right of point A. An acute angle between the rod and the horizontal is labeled as theta. Determine the speed of the sphere at the instant θ = 90∘ . Neglect the mass of rod AB and the size of the sphere.
The spool has a mass m, and a radius of gyration kG. An inextensible cord is attached to the wall at A. The cord is wound around the inner radius, R, and the outer radius is 2R. The coefficient of friction between the spool and the ground is mu. If instead of applying the force, F, at point B, the spool has an initial angular velocity given as omega naught. Use the work-energy principle to determine how far the center G will move before stopping.
A spool of mass 60 kg is supported on two rollers at A and B as shown in Figure Q1(c). Neglect the mass of the inelastic cable, friction and the mass of the rollers at A and B. Knowing that a constant pulling force P is applied in order to unwind 6 m of cable in 3 s starting from rest. The radius of gyration for the spool is (600+a) mm, where a = 8. Appendix A shows the examples of identifying the radius of gyration using student ID. Determine the pulling force P.
The uniform slender bar shown in Figure 1 is pinned at a distance l= 27.3cm from its center of mass. The bar is releasedfrom rest with θ = 19◦ with the force of gravity acting in the -y-direction shown in the figure. The bar is 99cm long andhas a mass of 16kg. Determine the reaction at A immediately after release.