only answer 4, 5, 6 wmot=0t=02.7 kQ120 V+5 μΕ10 kQ50 kQConsider the circuit above. The switch has been closed for a very long time before opening at t=0s.Determine the following:1. Capacitor voltage (in Volts) right before the switch has been opened2. Time constant of the circuit for t > 0. Express your answer in ms.3. Expression for the capacitor voltage for t 204. Expression for the capacitor current for t >05. Sketch Ic(t) and Vc(t) for t > 06. Total dissipated energy (in microjoules) in the 10k ohm resistor 5ms after the switch has beenopened

To solve above question, one should understand the behavior of Inductor and capacitor in DC circuit.…

Answered: 4. Expression for the capacitor current…

4. Expression for the capacitor current for t > 0 5. Sketch Ic(t) and Vc(t) for t 2 0 6. Total dissipated energy (in microjoules) in the 10k ohm resistor 5ms after the switch has been opened

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A capacitor consists of two circular plates of radius a separated by a distance d(assume d << a). The centre of each plate is connected to the terminals of a voltagesource by a thin wire. A switch in the circuit is closed at time t = 0 and a current I(t) flows in the circuit. Thecharge on the plate is related to the current according to I (t) = dq/dt. We begin bycalculating the electric field between the plates. Throughout this problem you mayignore edge effects. We assume that the electric field is zero for r > a.(A) Use Gauss’ Law to find the electric field between the plates as a functionof time t, in terms of q(t), a, ε, and π. The vertical direction is the k direction. (B)Now take an imaginary flat disc of radius r < a inside the capacitor, as shownbelow. Using your expression for E above, calculate the electric flux through this flatdisc of radius r < a in the plane midway between the plates, in terms of r, q(t), a,and ε. (C)Calculate the Maxwell displacement…
An electrical circuit has a very small resistance so it can be despised. The capacitor on the left was charged up to the voltage of Vo=10 volts and then, at time t=0, the switch S was closed. The capacity of the capacitors are C=60 µF, and the coil inductance is L=0.04 HI) Find the voltage on the left capacitor, at the instant V1=0.001 s.II) Find the voltage in the right capacitor, at the instant t=002 s.
The voltage pulse applied to the 100 mH inductor shown is 0 for t<0. and is given by the expression v(t)=20te−10t V for t>0. Also assume i=0 for t≤0. Sketch the voltage as a function of time.
A capacitor consists of two circular plates of radius a separated by a distance d (assume d << a). The centre of each plate is connected to the terminals of a voltage source by a thin wire. A switch in the circuit is closed at time t = 0 and a current I(t) flows in the circuit. The charge on the plate is related to the current according to I (t) = dq/dt. We begin by calculating the electric field between the plates. Throughout this problem you may ignore edge effects. We assume that the electric field is zero for r > a. (A) Use Gauss’ Law to find the electric field between the plates as a function of time t, in terms of q(t), a, ε, and π. The vertical direction is the k (b) Now take an imaginary flat disc of radius r < a inside the capacitor, as shown below. Using your expression for E above, calculate the electric flux through this flat disc of radius r < a in the plane midway between the plates, in terms of r, q(t), a, and ε. (C) Calculate the Maxwell…
Consider the given circuit. The switch has been closed for a very long time before opening at t=0s. Determine the capacitor voltage (in volts) right before the switch has been opened, the time constant of the circuit for t>0 (in ms), and the expression for the capacitor voltage for t≥0.
1. A capacitor consists of two circular plates of radius a separated by a distance d (assume d << a). The centre of each plate is connected to the terminals of a voltage source by a thin wire. A switch in the circuit is closed at time t = 0 and a current I(t) flows in the circuit. The charge on the plate is related to the current according to I (t) = dq/dt. We begin by calculating the electric field between the plates. Throughout this problem you may ignore edge effects. We assume that the electric field is zero for r > a. (A) Use Gauss’ Law to find the electric field between the plates as a function of time t, in terms of q(t), a, ε, and π. The vertical direction is the k direction. (B) Now take an imaginary flat disc of radius r < a inside the capacitor, Using your expression for E above, calculate the electric flux through this flat disc of radius r < a in the plane midway between the plates, in terms of r, q(t), a, and ε. (C) Calculate the Maxwell displacement…
When a capacitor holding an initial electrical charge of 60 microcoulombs (µC) is discharged through an electrical circuit, the remaining charge on the capacitor is q(t) = 60e-t/4 , where t is time elapsed in seconds. (a) Find q'(t), the electrical current in the circuit, as a function of t. (b) When is the magnitude of the electrical current in the circuit the greatest, and what is its value at this time?
IN THE CIRCUIT SHOWN, CONSIDER THAT V1=20 VDC, R1=1000 Ω, R2=3000 Ω, R3=3500 Ω AND C=1 mF.DETERMINE:A) THE TIME IT TAKES FOR THE CAPACITOR TO REACH ITS FINAL VALUE (5T), WHEN SWITCH 2 (INT 2) IS IN POSITION A AND SWITCH 1 (INT 1) IS CLOSED AT t=0,B) THE ENERGY STORED BY THE CAPACITOR ONCE IT HAS BEEN FULLY CHARGED WITH THE SAME POSITION OF SWITCHES AS ITEM A)C) ONCE THE CAPACITOR HAS BEEN FULLY CHARGED WITH SWITCH 1 CLOSED, SWITCH 2 MOVES POSITION (GOES TO B) AT A NEW t=0. NOW DETERMINE THE VALUE OF THE VOLTAGE ON THE CAPACITOR AT t=3.5 SECONDS
Let Vs=530tᶾ v, leg t >0 and iL (0) = 1 A, in the circuit shown, at t=0.2s, determine the values of the energy stored in the capacitor and the coil. The circuit is in the attached image.
Can you please help with this question? The triangular voltage pulse shown below is applied to a 200 mF capacitor. a) Write the expressions thatdescribe vc(t) in the five time intervals t < 0, 0 ≤ t ≤ 2 , 2 ≤ t ≤ 6, 6 ≤ t ≤ 8, and t > 8. b) Derive theexpressions for the capacitor current, power, and energy for the time intervals in part (a).
Consider the circuit above. The switch has been closed for a very long time before opening at t=0s. Determine the Inductor current (in amperes) right after the switch has been opened, the time constant of the circuit for ?>0 (in ms), and the Expression for the inductor current for ?≥0.
An electrical circuit contains a resistance R ohms and a capacitor C farads which initially holds acharge Q coulombs. The rate of discharge of the capacitor is given by the equation dQ/dt + Q/RC =0where t is the time in seconds. If R = 80,000 ohms and C = 0·3x 10^-6 farads and also Q = 0·0015coulombs initially, find the equation connecting Q and t. Find Q when t = 0·02 seconds and also twhen Q = 0·001 coulombs