4. In a pumping system handling water, the surface level of water in the open suction tank is 3m below the pump centerline, and the surface level in the open discharge tank is 22m above the pump centerline. The inlet piping is 7.62cm in diameter has an equivalent length of 26m of steel pipe. The discharge line is 6.35cm in diameter has an equivalent length of 72m. The pump discharge rate is 12.6 L/s. The friction factor to be 0.024 for both inlet and discharge pipes. Determine:

4. In a pumping system handling water, the surface level of water in the open suction tank is 3m below the pump centerline, and the surface level in the open discharge tank is 22m above the pump centerline. The inlet piping is 7.62cm in diameter has an equivalent length of 26m of steel pipe. The discharge line is 6.35cm in diameter has an equivalent length of 72m. The pump discharge rate is 12.6 L/s. The friction factor to be 0.024 for both inlet and discharge pipes. Determine:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water at 16,2°C is to be discharged from a reservoir at a rate of 16,2 L/s using two horizontal cast iron (roughness value ɛ=0.00026m) pipes connected in series and a pump between them. The first pipe is 26,2 m long and has a 66,2 mm diameter, while the second pipe is 36,2 m long and has a 46,2 mm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged (KL=0.562), and losses associated with the connection of the pump are negligible. Neglecting the effect of the kinetic energy correction factor, determine the required pumping head, the minimum pumping power and electric motor power for total efficiency value of 76,2% to maintain the indicated flow rate. Water density is r=996,2 kg/m3, dynamic viscosity µ= 1.162x10-3kg/ms. Solve the problem by making the necessary assumptions and drawing the schematic figure.
In a pumping system handling water, the surface level of water in the open sanction tank is 3m below the pump centerline and the surface level in the tank is 23m above the pump centerline. The inlet piping ia 7.62cm in diameter has an equivalent of 26m of steel pipe. The discharge line is 6.35cm in diameter has an equivalent lenght of 72m. The pump discharge rate is 12.6 L/s. the friction factor to be 0.024 for both inlet and discharge pipes. Determine: The total head loss due to friction (HL=hfs+hfd) in meters 21.955 3.187 25.142 The total dynamic head in meters 51.142 45.955 49.142 The water power in kW 5.678 6.072 6.319
Water is pumped from a reservoir to a pressurized storage tank (P = 150 kPa gauge) atop a building by means of a centrifugal pump. There is a 70-m difference in elevation between the water surface in the reservoir and the end of the discharge line. The piping system consists of 80m of 5" SCH 40 steel pipe containing two 90o elbows, one gate valve, one rotary water meter, and six couplings from the reservoir to the pump; 3" SCH 40 steel pipe for 86m to the tank. The 3" pipe contains two gate valves, four 90o elbows, and ten couplings. It is desired to maintain a flow of water into the tank of 2.4 m3/min. Water temperature is 25oC. If the pump-motor set has efficiency of 65%, what would be the pumping costs be in pesos per day if electricity costs PhP 10.50/kW-hr?
A centrifugal pump draws water from a 38cm pipe from an open reservoir in which the water surface is 2.6m below the pump centerline and discharges through a 30cm pipe. At a point in the discharge 2.35m above the pump centerline a pressure gage reads 320 kPa gage. The discharge is 200Liters/sec, the head loss in the suction is 0.15m and in the discharge is 1.05m. Power input to the pump is 140hp. Determine the following: a. The total dynamic head in meters 36.923 41.527 39.188 b. The Water Power (WP) in kW 76.863 80.451 81.451 c. The pump efficiency in percent 77.659 73.596 80.876
A water source with an elevation of 12 m is to be pumped by a centrifugal pump to an open reservoir at an elevation of 100 m. The suction pipe and discharge pipe diameter is 250mm and 200 mm, respectively. The pump centreline is at 5m. The head loss at suction pipe is 0.05m and 0.45 at the discharge pipe. The pump delivers water at 15 L/s and has an efficiency of 75% while the electric motor is 80%. Determine: a. Water horsepower of the pump b. Brake horsepower of the pump c. Power input to drive the motor, in kW d. The pressure gage readings installed before and after the suction and discharge of the pump, kPa.
Water is pumped to a storage tank from a pool by a centrifugal pump. The elevation difference between the pool and the storage tank is 60 m. The stórage tank and the pool are open to atmosphere. 50 meters of 6 in Sc 40 steel pipe is used between pool andpump. After the pump 6 in Sc 40 pipe with a length of 22 m is suddenly contracted to 4 in Sc 40 pipe, that is 70 m. The flow rate of water is 2.5 m/min and the temperature is 20°C. If the pump efficiency is 0.6 and the cost of electrical energy is 0.40 TL/kWh,calculate daily cost of electricity used for this system
A pump is being used to transport a liquid food product (ρ = 1250 kg/m3, μ = 1.5 cP) from a holding tank to a filling machine at mass flow rate of 2.5 kg/s. The liquid level in the holding tank is 10 m above the pump, and the filling machine is 5 m above the pump. There is 100 m of 2-in nominal diameter sanitary pipeline between the holding tank and the filling machine, with open globe valve and three regular 900 flanged elbows in the system. The product is being pumped through a heat exchanger with 120 kPa of pressure drop due to friction before filling. Complete the process diagram and determine the actual power requirement if the efficiency of the pump and the motor are 85 % and 80%, respectively.
The length and diameter of a suction pipe of a single-acting reciprocating pump are 5m and 10 cm respectively. The pump has a plunger of diameter 15cm and a stroke length of 35 cm. The center of the pump is 3 m above the water surface in the pump. The atmospheric pressure head is 10.3 m of water and pump is running at 3r rpm. Determine: a. Pressure head due to acceleration at the beginning of the suction stroke, b. maximum pressure head due to acceleration and c. pressure head in the cylinder at the beginning and at the end of the stroke
In a 3.5 MW hydroelectric power plant, the elevation of the headwater is 2100 m and that of a tailwater is 180 m. Penstock diameter is 750 mm. The water is flowing at a velocity of 5 m/s, and the total head loss is 15% of the gross head. The impulse turbine nozzle is 3.0 m above tailwater level. Penstock length is 1220 m, electrical efficiency is 95%. Calculate mechanical efficiency (%).
In a pumping system handling water, the surface level of water in the open suction tank is 3m below the pump centerline, and the surface level in the open discharge tank is 22m above the pump centerline. The inlet piping is 7.62cm in diameter has an equivalent length of 26m of steel pipe. The discharge line is 6.35cm in diameter has an equivalent length of 72m. The pump discharge rate is 12.6 L/s. The friction factor to be 0.024 for both inlet and discharge pipes. Determine: a. the total head loss due to friction (HL = hfs + hfd) in meters 21.955 3.187 25.142 b. the total dynamic head in meters 50.142 45.955 49.142 c. the water power in kW 6.196 6.072 5.684
Water at 50oF ( γ = 62.4 lbf/ft3 ; pv = 0.1733 psia) is to pump between open reservoir A and B whose surfaces are at elevations 5910 ft and 6060 ft, respectively (patm = 11.8 psia). The water is to be delivered at 20 cfs through a 24-in diameter pipe of length 2000 ft. Assume pipe friction factor f = 0.03. (a) Find the specific speed of the most suitable pump if the speed of operation is to 600 rpm. (b) If this pump is installed 10 ft above the water surface of reservoir A with suction pipe total length 300 ft will it be safe against cavitation? (c) What maximum elevation above water surface of reservoir A the pump can be installed without pump cavition? Pump NPSHR is 8 ft.
The initial condition of air in an air compressor is 100 Kpa and 25 degrees Celcius and discharges air at 725 Kpa. The bore and stroke are 276 mm and 186 mm respectively with 3 % clearance runningat 6 rev/sec.1.1 Illustrate the PV diagram 1.2 Discuss the processes in PV diagram 1.3 Solve the volumetric effieciency