4. Oil (SG = 0.84) is flowing between two sections in a pipe at 56 liters/s. At section 1, the pipe diameter is 150 mm, the pressure is 445 kPa gage, and the elevation is 3.21 m. At section 2, the pipe diameter is 225 mm, and the elevation is 1.2 m. If the total head loss from point 1 to point 2 is 900 mm, find the gage pressure at point 2 find the gage pressure at point 2 in kPa gage 457.5 O 475.6 547.5

4. Oil (SG = 0.84) is flowing between two sections in a pipe at 56 liters/s. At section 1, the pipe diameter is 150 mm, the pressure is 445 kPa gage, and the elevation is 3.21 m. At section 2, the pipe diameter is 225 mm, and the elevation is 1.2 m. If the total head loss from point 1 to point 2 is 900 mm, find the gage pressure at point 2 find the gage pressure at point 2 in kPa gage 457.5 O 475.6 547.5

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe, the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B.
A pipe, 12 inch in diameter at A, discharges 4.0 cfs of heavy fuel oil (sp gr = 0.899) into the air at B, where the diameter is 6 inch. If B is 12 ft above A and the frictional loss between the two points is equivalent to 3.0 lb per sq in, determine the pressure at A in pounds per square inch.
pump with critical cavitation number 0,08 pumps water to a total head of 60 m and temperature of 15°C (Pv=1707 Pa). If the barometric pressure is 98 kPa, head loss in the suction pipe is 1m. Find the maximum value of static suction lift in meters to avoid cavitation in the pump.
At point A where the diameter at of the pipe is 18 cm the pressure reading is 22.5 cm of Mercury. At point B, 3 m lower than A, the diameter is 48 cm and the pressure reading is 50 cm of Mercury. If the total head loss between the two points is 1.50 m, solve for the discharge. Water is flowing through the pipe. subject: hydraulics
Find the pressure head at entry of the pipe, when the pressure of flowing fluid is 275 N/cm? The pressure head at entry (Unit in Pascal)?
Q3: Find the diameter of a circular orifice to discharge (0.015m '/ sec) under a head of (2.4m). If the orifice is in a vertical plane and the jet falls (0.25m) in a horizontal distance of (1.3m) from the vena-contracta. Find the head loss through the orifice
C3. An oil of specific gravity 0.85 is flowing through a horizontal venturimeter fitted to a 240 mm diameter pipe at the rate of 102 liters/s and throat diameter is 98 mm. The entrance and throat of the venturimeter are connected in the two limbs of a U-tube mercury manometer. The difference in mercury level shows 835 mm. Calculate (i) the head difference in m of oil, (ii) the theoretical discharge in m3/s, (iii) the actual discharge in m3/s, and (iv) the coefficient of discharge of a venturimeter. If instead of a U-tube mercury manometer, the pressure gauges are inserted at the entrance and throat of venturimeter. Find (v) the pressure at the throat in N/mm2, if the entrance pressure gauge shows0.126 N/mm2. (Enter only the values by referring to the unit given. Also, upload the handwritten answers in the link provided) (i) the head difference in m of oil (ii) the theoretical discharge in m3/s (iii) the actual discharge in m3/s (iv) the coefficient of…
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450 mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively. If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
A 12′′ pipe line carries oil of specific gravity 0.811 at a velocity of 80.0 ft/sec. At points A and B, measurements of pressure and elevation were 52.6 psi and 100.0 ft and 42.0 psi and 110.0 ft,respectively. For steady flow, find the lost head between A and B. indicate the free body diagram
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
Water flows through a pipe at 130 L/s that changes gradually in diameter from 154 mm at point A to 429 mm at point B. B is 4.6 m higher than point A. The respective pressures at A and B are 70 kPa and 48.30 kPa. All minor losses are insignificant. Determine the total head lost.
The water is flowing through a taper pipe of length 100 m having diameters 600 mm at the upper end and 300 mm at the lower end, at the rate of 60 litres/s. The pipe has a slope of 1 in 40. Find the pressure at the lower end if the pressure at the higher level is 22 N/ cm².