Taking atmospheric pressure head = 10.3 m of water. A 100 mm diameter horizontal pipe has a venturimeter of 0.5 contraction ratio. For no flow the head of water on the metre is 3 m (gauge). Find the rate of flow for which the throat pressure will be 2 metres of water absolute. The co-efficient of meter is 0.97

Taking atmospheric pressure head = 10.3 m of water. A 100 mm diameter horizontal pipe has a venturimeter of 0.5 contraction ratio. For no flow the head of water on the metre is 3 m (gauge). Find the rate of flow for which the throat pressure will be 2 metres of water absolute. The co-efficient of meter is 0.97

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the siphon in Fig. 6.26, calculate the distance X re-quired to obtain a volume flow rate of 7.1 X 10-3m³/s.
The volumetric flow of water is 665.98 liters/min. Calculate the maximum length [m] of the pipe that can be used without cavitation? (NOTE: Take the water temperature 10 °C)
What is the performance of pump (in %, whole number) that supplies 80 gpm of water (80°F) with pressure of145 ft head?
Q3: Find the diameter of a circular orifice to discharge (0.015m '/ sec) under a head of (2.4m). If the orifice is in a vertical plane and the jet falls (0.25m) in a horizontal distance of (1.3m) from the vena-contracta. Find the head loss through the orifice
nlet and throat diameters of a horizontal venturimeter are 350 mm and 150mm respectively. The liquid flowing through the venturimeter is water. Pressure intensity at inlet is 13.734 N/cm2 , while pressure at throat is 68.66 kPa. Find the actual flow rate, assuming Cd is 0.78.
A sharp edged orifice will be required to produce a discharge of 35 liters/sec of water under a head of 3m. Find the required diameter, when C = 0.595
B Refer to, Fig. X5.2.2. Assume a = 1 m, b = 4 m, and the flow to be frictionless in the siphon. Find the rate of discharge in mºls and the pressure head at B if the pipe has a uniform diameter of 150 mm. M Tar N
a venturimeter with inlet and throat diameters 300 mm and 150 mm respectively is attached in a vertical pipe in which flow occurs from bottom to top. the distance between the point of entrance and to the point of throat of the venturimeter is 750 mm. if the difference of mercury levels in the two limbs of differential gauge is 220 mm, find the discharge passing through the vertical pipe. take co-efficient of discharge, Cd = 0.98.
A pump with an efficiency of 89.842 percent delivers water at a rate of 13.79 m3/s but with a leakage loss of 0.5 m3/s. The friction losses within the pump result in a 1 m head loss. What is the total dynamic head of the pump in meters if it has a mechanical efficiency of 98 percent?
A centrifugal pump developing 9 ft head at 1200 rpm is driven by a 3 hp motor. Impeller diameter is 6-in. Discharge is 1300 gpm. Determine the critical cavitation parameter ?
Calculate the minimal head of the pump required to pump 1 m³ of water per second to the height 10 m trough a pipe with cross sectional area 0.1 m². Assume constant friction coefficient f = 0.04 and neglect all losses in fittings. The pump head is the gravity head plus losses and so it can be found?
Pressures at the start and end of a straight horizontal pipe pumping water are measured as 2560337.6Pa and 168693.4Pa, respectively. Calculate the head loss due to friction. (Lemme Know If anything missed)