4. Points A and B are 1.5 km apart along a 15 cm diameter new steel pipe (ks = 4.6 x 10 m). Point B is 20 m higher than A. With a flow from A to B of 0.03 m³/s of crude oil (SG 0.82) at 10 °C (μ = 10-2 N-s/m²), what pressure must be maintained at A if the pressure a B is to be 300 kPa gage?

4. Points A and B are 1.5 km apart along a 15 cm diameter new steel pipe (ks = 4.6 x 10 m). Point B is 20 m higher than A. With a flow from A to B of 0.03 m³/s of crude oil (SG 0.82) at 10 °C (μ = 10-2 N-s/m²), what pressure must be maintained at A if the pressure a B is to be 300 kPa gage?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water at 15°C (? = 999.1 kg/m3 and ? = 1.138 × 10−3 kg/m·s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.
5.3 If the pressure head difference at point 1 and 2 is 0.2m of water for laminar flow through a circular horizontal pipe of diameter 200mm and the absolute viscosity of water is 10 poise, find the discharge, which will be conveyed through the pipe of length 30m?
Points A and B are separated by 915 m of new 152.4 mm diameter castiron pipe. 50 lps of water flow from point A to point B. Point B is 18.5 m abovepoint A. What must be the pressure at point A if the pressure at point B is 345kPag and the head loss between A and B is 54 m?
Two water reservoirs of height h1 = 60 m and h2 = 30 m are connected by a pipe that is 0.35 m in diameter. The exit of the pipe is submerged at a distance of 8 m from the (2nd) reservoir surface. a. Provide a diagram b. Determine the flow rate through the pipe if the pipe is 80 m long and the (Fanning) friction factor f' = 0.004. The pipe inlet is set flush with the wall. c. If the relative roughness ε/D = 0.004, determine the friction factor and flow rate.
1. A long siphon connected at the side near the bottom of the reservoir discharges water through a nozzle 200mm by 50 mm creating a jet. Various points were identified located along the siphon: Point A is located after the reservoir connection, Point B is 4 m above Point A, Point C is 3 m above Point A, and Point D is 1 m below Point A and located before the nozzle. Determine the flow in m3/s along the siphon and the pressure in kPa at Point A, Point B, Point C, and Point D. Consider that the level of the reservoir is same with Point C. Assume no head loss along the siphon. 2. Two interconnected pipes A and B with 300 mm and 200 mm diameter, respectively, carries a flow of 0.116 m3/s. Determine the velocity in m/s of pipe A and pipe B. If pipe B was replaced with 400 mm diameter, determine the velocity in m/s of pipe B. 3. The 500 mm diameter pipe conveys treated water to supply a municipality with a demand of 40 MLD. Determine the head loss in meter if the length of the pipe is 10 km…
Two reservoirs whose surface levels differ by 30 meters are connected by a pipe 600mm diameter and 3000m long. The pipe line crosses a ridge whose summit is 9m above the level of and 300m distant from the higher reservoir. Find the minimum depth below the ridge at which the pipe must be laid if the absolute pressure head in the pipe is not to fall below 2.5m of water, and calculate the discharge. Take atmospheric pressure head = 10.3m of water and f= 0.0075
A pipe AB carries water and tapers uniformly from a diameter of 0.1 m at A to 0.2 m at B over a length of 2 m. Pressure gauges are installed at A, B and also at C, the midpoint of AB. If the pipe centerline slopes upwards from A to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3 bar, respectively. (1 bar = 100 kPa) Determine the flow, in m^3/s through the pipe at C neglecting all losses. (1 bar = 100 kPa). (Please round-off final answer to four decimal places) Determine the pressure in bars, recorded at C neglecting all losses. (Please round-off final answer to 2 decimal places)
A pipeline connected to a reservoir discharges water 30 m below the free surface in the tank. The pipeline crosses a ridge whose summit is 9 m above the level of free surface and 300 mm distant from the reservoir. The pipe is 0.6 m in diameter and 3 000 m long and the connection is sharp and sudden. Take ƒ = 0.0075. Finda, the minimum depth below the ridge at which the pipe must be laid, if the absolute pressure in the pipe is not to fall below 3 m of water.b, the discharge
A 300 mm cast-iron pipe is discharge 120 lit/sec. At a point 200 m from the reservoir the center of the pipe is 30 m below the reservoir surface. What is the pressure in kPa to be exerted there? Assume f= 0.02
An engineer is hired to design a swimming pool 15m long by 6m wide by 2m deep. For water supply, he decideds to lay 600m of 5cm pipe with f=0.020 from a nearby main to the pool. The pipe will discharge freely into the pool during the entire filling process. The average pressure at the water main is 550kpa and the difference in elevation between the two ends of the pipe is 10m, with the discharge end higher than the intake end. Assuming that 10% of the loss in the pipeline are due to transitions, fittings and valves, how long would it take to fill the swimming pool?
Water is pumped from reservoir A through 1850 m pipeline 600 mm across a valley to a second reservoir C. the water surface elevation of reservoir A is at elevation 61 m and that of C is at elevation 91m. If during pumping, the pressure at B which is located midway of the 600 mm pipe and at elevation 30 is 100 kPa. Compute the flow rate and the horsepower exerted by the pump if f = 0.02.
6. Compute the lost head in a 150-mm pipe if it is necessary to maintain a pressure of 231 kPa at a point upstream and 1.83 m below where the pipe discharges water into the atmosphere at the rate of 0.0556 m /s. indicate free body diagram