4. The maximum values of the alternating voltage and current are 400 V and 20 A respectively in a circuit connected to 50 Hz supply and these quantities are sinusoidal. The instantaneous values of the voltage and current are 283 V and 10 A respectively at t = 0, both increasing positively. Write down the expression for voltage and current at time t and determine its phase difference and indicate which quality leads or lags the other.

4. The maximum values of the alternating voltage and current are 400 V and 20 A respectively in a circuit connected to 50 Hz supply and these quantities are sinusoidal. The instantaneous values of the voltage and current are 283 V and 10 A respectively at t = 0, both increasing positively. Write down the expression for voltage and current at time t and determine its phase difference and indicate which quality leads or lags the other.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
In the circuit shown in the figure, there is a load between the terminals a and b, consisting of the series connection of the resistor R0 and the inductance L0. The amplitude of the voltage Vs (t) is two root hundred and fifty phase angle Qs = zero degree period T = 200 PI microseconds. Since R = 300 ohms C = 1 nano F. a) Find the values of R0 and L0 that enable the load to draw maximum average power from the circuit b) Calculate the complex power on the load.
Q6: An AC source operating at 60 Hz with a maximum voltage of 170 V is fed to a series combination of1.2kΩ resistor and 2.5μF capacitor connected in a timer circuit. How can you evaluate the maximumcurrent in the circuit? Can you estimate the rms value potential difference across each circuit element?Compare the power factor of this timer circuit with a circuit contain only ohmic resistance. Justify youranswer?
Suppose the circuit shown represents a residential distribution circuit in which the impedances of the service conductors are negligible and Vg1=Vg2=120 0° V (rms). The three loads in the circuit are L1 (a new refrigerator, a coffee maker, and a microwave oven); L2 (2 incandescent lamps, a humidifier, and a ceiling fan); and L3 (a clothes washer and a clothes dryer). Assume that all of these appliances are in operation at the same time. The service conductors are protected with 20 A circuit breakers. Will the service to this residence beinterrupted? Why or why not?
A source whose voltage is ? (?) = 50√2 cos (?? + 30 °) ? supplies a load ofimpedance ? = (4 + ?3) Ω. Saber is intended to: a) the active, reactive and apparent powerconsumed by the load. b) a capacitor power that must be installed in parallelwith the load to raise its power factor to 0.97 delayed.
An example power system has two distinct manufacturing areas, one with harmonic loads, and another with only linear loads. The portion of the system with the harmonic loads draws 75 A rms at 60 Hz, 10 A rms at 300 Hz, and 5 A rms at 420 Hz. The part of the system with only linear loads draws 75 A rms at 60 Hz. (i) What is the total load current (at 60 Hz) if both manufacturing plants are running? Calculate the THD. (ii) What is the total load current (at 60 Hz) if only the manufacturing plant with harmonic loads is running? Calculate the THD.
The variable resistor Ro in the circuit shown is adjusted until maximum average power is delivered to Ro.1. a) What is the value of Ro in ohms?2. b) Calculate the average power delivered to Ro.3. c) If Ro is replaced with a variable impedance Zo, what is themaximum average power that can be delivered to Zo?4. d) In (c), what percentage of the circuit’s developed power isdelivered to the load Zo?
Given a sinusoidal voltage source in series with R,L, and C. The sinusoidal frequency is 600 Hz. R=2 Ohms, L=5 milliHenry, C=200 microFarad, V=70sin(wt) volts. Determine the watts and VARs for the capacitor, resistor, inductor, and source. Also find power factor. Given R1=9 Ohms, R2=1 Ohms, L= 3 milliHenries, and a sinusoidal voltage source of 5 volts amplitude and 60 Hz freqency all in series. Determine the voltage across R1: magnitude (volts), frequency (Hz), and phase (degrees).
The sending-end voltage in the circuit seen is adjusted so that the load voltage is always 13,800 V(rms). The variable capacitor is adjusted until the average power dissipated in the line resistance is minimum. 1. a) If the frequency of the sinusoidal source is 60 Hz, what is thevalue of the capacitance in microfarads?2. b) If the capacitor is removed from the circuit, what percentageincrease in the magnitude of Vs is necessary to maintain 13,800V(rms) at the load?3. c) If the capacitor is removed from the circuit, what is thepercentage increase in line loss?
The 9 Ω resistor in the circuit is replaced with a variable impedance Zo. Assume Zo is adjusted for maximum average power transfer to Zo. 1. a) What is the maximum average power that can be delivered toZo?2. b) What is the average power developed by the ideal voltage sourcewhen maximum average power is delivered to Zo?3. c) Choose single components from Appendix H to form animpedance that dissipates average power closest to the value in part(a). Assume the source frequency is 60 Hz.
q13/ choose the correct answer The variation of the load is considered over a period of one year in an annual load curve. Select one: True False
A source whose voltage is ? (?) = 50√2 cos (?? + 30 °) ? supplies a load of impedance ? = (4 + ?3) Ω. We want to know: a) the active, reactive and apparent power consumed by the load. b) the power of a capacitor that must be installed in parallel with the load to raise its power factor to 0.97 delayed.