4. The shaft that is pictured is to be loaded by a purely reversing load, cycling at ± 500 lbf. The shaft is to be machined, operate in an environment at 100°C, have a reliability of 90%, and be made of a material in which Sut = 80 kpsi and Sy = 65 kpsi. The stress concentrations at A are K: = 1.6 for bending and Kt = 2.0 for torsion. Assume the notch sensitivity factor for torsion and bending to be 1.0. 10 inches a. Using the information provided with the attached log-log scale, create an S-N diagram assuming a steel shaft subjected to only bending. Estimate how many cycles of life can be expected if the alternating stress is 60 kpsi. F = ± 500 lbf b. would the S-N diagram from part (a) be different if only torsion were experienced (no bending)? Briefly explain why. B 8 inches C. (.. Using a factor of safety of 2.0 based on infinite life, determine the minimum allowable diameter for shaft AB using the modified-Goodman criterion.

4. The shaft that is pictured is to be loaded by a purely reversing load, cycling at ± 500 lbf. The shaft is to be machined, operate in an environment at 100°C, have a reliability of 90%, and be made of a material in which Sut = 80 kpsi and Sy = 65 kpsi. The stress concentrations at A are K: = 1.6 for bending and Kt = 2.0 for torsion. Assume the notch sensitivity factor for torsion and bending to be 1.0. 10 inches a. Using the information provided with the attached log-log scale, create an S-N diagram assuming a steel shaft subjected to only bending. Estimate how many cycles of life can be expected if the alternating stress is 60 kpsi. F = ± 500 lbf b. would the S-N diagram from part (a) be different if only torsion were experienced (no bending)? Briefly explain why. B 8 inches C. (.. Using a factor of safety of 2.0 based on infinite life, determine the minimum allowable diameter for shaft AB using the modified-Goodman criterion.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 15KW and 1200r.p.m motor drives a compressor at 300r.p.m through a pair of spur gears having 20° stub teeth .the centre to centre distance between the shafts is 400mm.the motor pinion is made to forged steel having an allowable static stress 210MPa while the gear is made of cast steel having an allowable static stress as 140MPa.Assuming that the drive operates 8 to 10 hours per day under light shock conditions,find from the standpoint of strength (a) Module;(b)face width and (c)number of teeth an pitch circle diameter of each gear.check the gears thus designed from the consideration of wear .the surface endurance limit may be taken as 700MPa.
A 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having 20° stub teeth. The centre to centre distance between the shafts is 400 mm. The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa. Assuming that the drive operates 8 to 10 hours per day under light shock conditions, find from the standpoint of strength, 1. Module; 2. Face width and 3. Number of teeth and pitch circle diameter of each gear. Check the gears thus designed from the consideration of wear. The surface endurance limit may be taken as 700 MP
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
A short stub shaft, made of SAE 1035, as rolled, receivers 30 hp at 300 rpm via a 12-in. spur gear, the power being delivered to another shaft through a flexible coupling. The gear is keyed (profile keyway) midway between the bearings. The pressure angle of the gear teeth   20o, N = 1.5 based on the octahedral shear stress theory with varying stresses. (a) Neglecting the radial component R of the tooth load W , determine the shaft diameter. (b) Considering both the tangential and the radial components, compute the shaft diameters. (c) Is the difference in the results of the parts (a) and (b) enough to change your choice of the shaft size?
Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of 796 N. m.
1.1. State three underlying assumptions in the formulation of the torsion formula, .TGJrl (3) 1.2 A hollow shaft has to be designed for a marine engine delivering 1200 kW when running at 120 r/min. The maximum allowable shear stress is 50 MPa and the maximum torque to be transmitted by the shaft is 30 % greater than the mean torque. The internal diameter of the shaft is 50 % that of the external diameter. Calculate: 1.2.1 The dimensions of the shaft and the angle of twist of the shaft over 3 m when transmitting the above torque (G = 80 GPa). (14) 1.3 Determine the torsional rigidity of a 300 mm long steel shaft with a diameter of 50 mm. (G = 80 GPa
Design of a Shaft subjected to Alternating Loads 1. [Proof of Concept] Considéra machined steel circular shaft subjected to maximum and minimum bending moment of 1000 and 4000 lb .in, respectively; and a maximum and minimum torque of 250 and 1600 Ib.in, respectively. Consider the factor of safety to be 2, the yield strength of the materials 40 ksi, and its ultimate strength to be 70ksi.Determine the minimum diameter of the shaft for the case where D is 20% larger than d, the fillet radius is 10% of d, and reliability is 99%. You may use DE-ASM E formula. 2. Write a computer code that can take Tm, Ta, Mm, Ma, choice of material, safety factor, and other necessary assumptions from the user and return an estimated diameter for the shaft.Choice of inputs is up to you. Note that many of the required quantities are themselves function of the shaft diameter. Your code should be submitted with a report.
Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be taken as 1.5. [
A rigid block is supported by two cables having the same diameter of 4 mm. Cable S1 is made of AISI 1050 cold drawn steel with E=200,000 MPa, Sy=580 MPa, and Sult=690 MPa; cable S2 is made of AISI 1020 cold drawn steel with E=200,000 MPa, Sy=390 MPa, and Sult=470 MPa. Determine the maximum number of cycles n3 due to the following history of P.
Bearing stress 5. Please provide proper discussion and illustration also complete solution and clear solution please thank you A solid shaft is designed to transmit 50kN @ 1800 rpm to a gear by means of 156 mm long key with square cross-section. The shaft diameter is 35.6mm. What should the cross-section be in mm2 to resist shearing, if the allowable shear stress on the key is 20 MPa?
5. Design a sleeve coupling for the transmission of 12 kW at 300 rpm by two connected steel shafts. Take service factor KS 1.25. The sleeve is made of CI. The key and the shaft are made of the same material. Allowable stress: Shear stresses in key and shaft 50 MPa Crushing stress in key= 100 MPa Shear stress in CI sleeve = 10 MPa
(4) A single square-thread power screw has an input power of 3.0kW at a speed of 1 rev/s. The screw has a major diameter of 36mm and a pitch of 6mm. The frictional coefficients are 0.14 for the threads and 0.09 for the collar, with a collar friction radius of 45mm. Find: (a) the axial resisting load F (b) the combined efficiency of the screw and collar;