4. The structure in the figure is composed of two rigid bars (AB and CD) and two verti rods made of aluminum and steel. All connections are pin joints. Determine the maximum force P that can be applied to the structure if the deformation of the Aluminum rod is limited to 6 mm. Neglect the weights of the members. Aluminum 2 m A= 300 mm E= 70 GPa Steel 2 mA = 500 mm? E = 200 GPa 3m 3 m

4. The structure in the figure is composed of two rigid bars (AB and CD) and two verti rods made of aluminum and steel. All connections are pin joints. Determine the maximum force P that can be applied to the structure if the deformation of the Aluminum rod is limited to 6 mm. Neglect the weights of the members. Aluminum 2 m A= 300 mm E= 70 GPa Steel 2 mA = 500 mm? E = 200 GPa 3m 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid horizontal bar articulated at the left end is supported by 2 elastic rods with a modulus of elasticity of 207 GPa. The length of the bar no. 1 is 1.7 m and the cross-sectional area is 8.1 cm^2 ; Since the length of the bar 2 is 1.3m and the cross-sectional area is 8.9 cm^2, as a result of the 49 KN force acting from the right end:a) How many kN is the internal force in rod 1?b) How many kN is the internal force in rod 2?c) By how many mm will point C of the rigid bar collapse?
A horizontal bar of negligible mass, hinged at A in FIGURE Z and assume rigid, is supported by a bronze rod 2 m long and a steel rod 1 m long. For the steel rod, the area is 600 mm², and E = 200 GPa. For the bronze rod, the area is 300 mm², and E = 83 GPa. Which of the following most nearly gives the elastic deformation in the bronze rod? a. 0.58 mm b. 1.36 mm c. 2.56 mm d. 3.18 mm
Refer to the figure, Beam Properties: Rod Properties: I = 198 x 10^6 mm4 Diameter = 11 mm E = 200 GPa E = 200 GPa Determine the following: a) Due to triangular load α, the rod support at right elongates by 5 mm. Find the force (kN) in rod which caused the elongation. b) Determine the value of α in kN/m? c) Determine the moment at fixed end in kN
Analyze the Structure given in Figure (Picture Attached) and determine the forces in each member of truss by GRAPHICAL METHOD. State whether members are in tension or compression. P1= 720KN P2= 360KN
The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the vertical displacement of point C if the stress in the steel rod is limited to 29.76 ksi, X = 2.07 ft, and Y = 4.93 ft. Neglect the weights of the members. Round off the final answer to four decimal places.
Analyze the Structure given in Figure (Picture Attached) and determine the forces in each member of truss by Methods of Joints. State whether members are in tension or compression. P1= 720KN P2= 360KN
When a force of F=350 N is applied to the arm of the clamping element in Figure 2, how much force is generated at A?
A vertical steel bar ABC is pin-supported at its upper end and loaded by a force P1 at its lower end. A horizontal beam BDE is pinned to the vertical bar at joint B and supported at point D. Load P2 and moment M are applied at end E. Calculate the vertical displacement δC at point C if the loads are P1 = 2.5 kip, P2 = 1 kip, and M = 25 kip-in. The modulus of elasticity is E = 29,000 ksi and crosssectional areas are A1 = 0.25 in2 A2 =0.15in2 .Ignore the weight of the bar.
Set P1 = 70 kN, P2 = 50 kN Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. a) Determine the force in member BG of the truss. b) Determine the force in member CD of the truss. c) Determine the force in member CF of the truss.
The two vertical rods attached to the rigid bar are identical except for length. Before the weight P was attached, the bar was horizontal. Neglect the weight of the bar. Calculate the axial force in rod A in kips (4 decimal), if P=53 kips.
The structure of the figure is composed of components DABC, HEB and GDEF that are connected by pins at B, D and E. There are also two loads at C and F. Determine the forces acting on points B and D.H = 83
the clamp exerts a normal force of 100N on the three pieces held together as shown. what force P may be exerted motion impends? the coefficient of friction between the pieces is .60