4.0m 7. The 4-mm-diameter cable BC is made of a steel with E= 200 GPa. Knowing that the maximum stress in the cable must not exceed 190 MPa and that the elongation of the cable must not exceed 6 mm, find the maximum load P that can be applied as shown.

4.0m 7. The 4-mm-diameter cable BC is made of a steel with E= 200 GPa. Knowing that the maximum stress in the cable must not exceed 190 MPa and that the elongation of the cable must not exceed 6 mm, find the maximum load P that can be applied as shown.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Ex : Two solid cylindrical rods AB and BC are welded together at B and loaded as shown , Knowing…

Q: 2.5m 3.5m 4.0m- The 4-mm diameter cable BC is made of steel with E = 200 GPa. Knowing that the…

Q: 4.23 A 900-mm strip of steel is bent into a full circle by two couples applied as shown. Determine…

Q: 4.123 The C-shaped steel bar is used as a dynamometer to determine the magnitude P of the forces…

A: Given: The side of cross-sectional area, s = 40 mm The strain on inner side, ε = 450µ The modulus of…

Q: The rectangular beam ABC, 100 mm wide by 400 mm deep, is supported by a pin at A and the cable CD.…

A: Given data :- width of beam = 100mm depth of beam = 400mm normal stress in the beam = 120 Mpa. find…

Q: The set shown in the figure consists of an aluminum ABC tube, with section AB having a diameter of…

A: Givendiameter of tube AB d1=20mmdaimeter of section BC d2=60mmP=4000N

Q: The aluminum rod AD is fitted with a jacket that is used to apply a hydrostatic pressure of 6000 psi…

A: The data given is, Stress in x-direction, ?x = -6000 psi Stress in y-direction, ?y = 0 Stress in…

Q: A 4-m-long steel rod must not stretch more than 3 mm and the normal stress must not exceed 150 MPa…

Q: Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid…

Q: For the connection shown, the average shear stress in the 15-mm-diameter bolts must be limited to…

Q: 2.2 (A) If the maximum stress allowed in the copper of the cabic of problem 2.I is 60 MN/m2,…

A: Given: Area of cross-section of the cable=6×10-5m2 Maximum allowable stress=60MN/m2 Maximum tension…

Q: Knowing that, for the plate shown, the allowable stress is 125 MPa, determine the maximum allowable…

A: Given Allowable stress =125 MPa Fillet radius a) 12 mm b) 18 mm To find Maximum value of P

Q: A rod must not stretch more than 6 mm when the tension in the wire is 8 kN. Knowing that E = 105 GPa…

Q: 4. Determine the yield stress of a steel rod 15 mm diameter, if the yield load on the steel rod is…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

Q: Straight rods of 0.30-in. diameter and 200-ft length are sometimes used to clear underground…

A: (a) The radius of the rod is given as, Moment of inertia is written as, The diameter of the spool…

Q: SThe 4-mm-diameter cable BC is made of a steel with E = 200 GPa. Knowing that the maximum stress in…

Q: PROBLEM 2.2 A 1.5 m long steel wire of 6 mm diameter steel wire is subjected to a 3.4 kN tensile…

Q: A cast-iron machine part is acted upon by the 3 kN-m couple shown. Know-ing that E= 165 GPa and…

A: Given data Couple acting on the machine part, M = 3 kN-m. Draw the cross-section of the beam,…

Q: A 7-mm-diameter wire (E = 150 GPa) supports a tension load of 6.5 kN. If the total elongation of the…

A: Given:d=7 mmE=150 GPaT=6.5 KN∆L=16 mmTHe change in length due to the applied axial force is given…

Q: The Bars of the Pin-connected frame as shown are each 30mm and 60mm in section. Determine the…

A: Given: σT=100 MPaσC=80 MPaSection=60 mm×30 mm The free-body diagram of the frame considering…

Q: The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminium…

Q: In the mechanism shown below, the distributed load W is 300 N/m and the angle 0 is 35°, knowing that…

Q: If the allowable tensile stress of the wires AB and AC is oallow = 250 Mpa, determine the largest…

Q: 4) An axial load P of magnitude 75 kN is applied as shown to a short section of a W200x59…

Q: Knowing that the clamp shown has been tightened on wooden planks being ghued together until P = 900…

Q: For the clevis connection shown, the shear stress in the 5/16-in.-diameter bolt must be limited to…

A: To Find : The maximum load P. Given : The shear stress is τ=20 ksi. The diameter is d=516 in. FBD:…

Q: For the shown static system, determine the minimum diameter of cable BD to withstand the shown load,…

Q: An aluminum [E = 10100 ksi] control rod with a circular cross section must not stretch more than…

Q: 2000 lb and Q = 4,000 lb, acting in the directions shown. Determine the horizontal displacement uc…

Q: A vertical force P of magnitude 20 kips is applied at point C located on the axis of symmetry of the…

A: Given Data: The magnitude of force P is, P=20 kips=20 kips×1000 lbkips=20×103 lb. The distance…

Q: 3. An eccentric load is applied at a point 22 mm from the geometric axis of a 60 mm diameter rod…

A: Given Stress = 200 MPa Young's modulus, E = 200 GPa Diameter, d =…

Q: Rigid bar ABC supports a weight of W = 26 kN. Bar ABC is pinned at A and supported at B by rod (1),…

A: Free body diagram

Q: A 8-mm-diameter wire (E = 90 GPa) supports a tension load of 5 kN. If the total elongation of the…

Q: 2. Determine the smallest allowable cross-sectional areas of each 400 kN members for the truss…

Q: A 8-mm-diameter wire (E = 120 GPa) supports a tension load of 1.5 kN. If the total elongation of the…

Q: 2.6 (B). A stanchion is formed by buttwelding together four plates of steel to form a square tube of…

Q: A centric axial force is applied to the steel bar shown. Knowing that σall=20 ksi, determine the…

A: Given Data At the hole the radius is r=0.5in Diameter, 5-1 = 4 in At 2rd=2(0.5)4=0.2 From the chart…

Q: A rod must not stretch more than 6 mm when the tension in the wire is 8 kN. Knowing that E = 105…

Q: A rigid bar AB of length L = 1600 mm is hinged to a support at A and supported by two vertical wires…

A: Given that: LAB = length of bar AB = 1600 mm LAC = length of AC = 500 mm LAD = length of AD = 1200…

Q: The steel rod ABC is made of a steel for which the yield strength is y = 250 MPa and the modulus of…

A: The maximum strain energy that can be acquired by the rod without causing any permanent deformation…

Q: 2.2 (A). If the maximum stress allowed in the copper of the cabie of problem 2.1 is 60 MN/m?,…

A: Given, The diameter of a single copper wire, d=1.6 mm No. of wires are 10 and there are such three…

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1 =…

Q: A nylon thread is subjected to a 8.5-N tension force. Knowing that E5 3.3 GPa and that the length of…

A: Given Data Strain= 1.1%=0.011 Tension force, P=8.5N Modulus of elasticity, E=3.3 GPa

Q: A timber beam AB of length L and rectangular cross section carries a single concentrated load P at…

A: Given: L=2 m P=40 kN maximum shear stress=960 kPa maximum normal stress=12 MPa

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: Answer: The flexural stress at the bottom fibre is 64.0909 MPa.

Q: A 150mm x 30mm x 250mm central wooden block is glued between cantilevered brackets 200mm x 50mm each…

A: Stress Stress is defined as the ratio of force to the area on which force is acting. There are…

Q: The bracket shown below is to carry a load F = 20 kN acting at an eccentricity of 1.2 from the…

A: givenbracket carry a load F = 20 kNeccentricity e=1.2 mshear stress in the rivets is not to exceed…

Q: 2.26 The length of the 2-mm-diameter steel wire CD has been adjusted so that with no load applied, a…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

25 m
17
18
19
3.5 m
20
4.0 m
7. The 4-mm-diameter cable BC is made of a steel with E= 200 GPa. Knowing that the maximum stress in the cable
must not exceed 190 MPa and that the elongation of the cable must not exceed 6 mm, find the maximum load P that can
be applied as shown.
OA1227 KN
OBI0.33 kN
OC13.03 kN
amak için buraya yazın

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The horizontal bar shown is pinned at O and is supported with a helical springat L1 from O. L1=2m, L2=1m. The spring has 30 turns and the diameter of the wire usedis 20mm. The diameter of the spring is 125mm. Modulus of Rigidity = 83GPa. Determine the shear stress of the helical spring loaded as shown if w = 25kN/m.
Three wires are used to suspend the plate shown. Aluminum wires of 18-in. diameter are used at A and Bwhile a steel wire of 112-in. diameter is used at C. Knowing that the allowable stress for aluminum (Ea510.4 3 106 psi) is 14 ksi and that the allowable stress for steel (Es529 3 106 psi) is 18 ksi, determine the maximum load P that can be applied
The pipe assembly shown is subjected to a force F = 7 kN and P = 14 kN. It is made of steel with Sy = 250 MPa. Determine the safety factor at point H using the maximum shear stress theory. Select one: a. NH = 6.427 b. NH = 3.570 c. NH = 5.355 d. NH = 4.590
The aluminum rod ABC (E = 10.1 × 106 psi), which consists of two cylindrical portions AB and BC, is to be replaced with a cylindrical steel rod DE (E = 29 × 106 psi) of the same overall length. Determine the minimum required diameter d of the steel rod if its vertical deformation is not to exceed the deformation of the aluminum rod under the same load and if the allowable stress in the steel rod is not to exceed 27 ksi. The minimum required diameter of the steel rod is in.
Knowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the alumi-num bar will be equal to –11 ksi, (b) the corresponding exact length of the aluminum bar.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (sY)st = 640 MPa, and for the bronze (sY)br = 520 MPa,determine the magnitude of the largest elastic load P that can be applied to the assembly. Est = 200 GPa, Ebr = 100 GPa.
steel bar ABCD consists of three sections: AB is of 30mm diameter and 100 mm long, BC is 20 mm square and 400 mm long, and CD is of 12 mm diameter and 200mm long. The bar is subjected to an axial compressive load which induces a stress of 50 MN/m2 on the largest cross-section. Determine the total decrease in the length of the bar when the load is applied. For steel E = 210GN/m2 .
Knowing that the AB pillar shown below is supported at points A andB, determine the greatest load (w) that can be applied to the beam before the column starts tobe buckled or before the steel runs out. Consider leakage voltage = 250 MPa, E=200 GPa, F.S. = 1.5.
' Three piates are joined with a 12-mm diameter pin as shown beiow. Determine the maximum load p that can be transmitted by the joint if the maximum bearing stress between a plate and the pin must be limited to 650 MPa .
A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (Es5 29 3 106 psi, αs5 6.5 3 10–6/°F) and portion BC is made of aluminum (Ea5 10.4 3 106psi, αa5 13.3 3 10–6/°F). Knowing that the rod is initially unstressed, determine (a) the normal stresses induced in portions AB and BC by a temperature rise of 70°F, (b) the corresponding deflection of point B
In the system shown, when a compression load P is applied to the rod, what is the bearing stress value in the bearings through which the d diameter pin passes? P = 10kN, pim çapı: d=20mm, bir yatağın kalınlığı: t = 10mm
1. (A). A 25mm square cross-section bar of length 300mm carries an axial compressive load of 50kN. Determine the stress set up in the bar and its change of length when the load is applied. For the bar material E = 200 GN/m?. [80 MN/m²; 0.12mm]