4.11 For the isolated buck boost converter as shown in the circuit below, the output voltage is to be 35 V at a duty cycle of 30%. The DC input is obtained from a front end rectifier without voltage doubling fed from a 115 V AC. What is the peak forward blocking voltage of the switching element? KH V₁ (a) 232.3 V (a) 6061 V +1 00000 S 00000 = (b) 69.69 V (d) 542 V ww

4.11 For the isolated buck boost converter as shown in the circuit below, the output voltage is to be 35 V at a duty cycle of 30%. The DC input is obtained from a front end rectifier without voltage doubling fed from a 115 V AC. What is the peak forward blocking voltage of the switching element? KH V₁ (a) 232.3 V (a) 6061 V +1 00000 S 00000 = (b) 69.69 V (d) 542 V ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Figure Q4.c shows an alternative regulator circuit that could be used in a DC powersupply design to regulate the output of a rectifier. Determine the suitability of the regulator for a rectifier with the output specifications asgiven in Table 4. The ripple voltage of the rectifier is 30% of Vpk, and the regulatorneeds to deliver to the load the current of Io mA.The Zener diode power rating is 2W. The required output voltage is 7.4V. For the circuit in Figure Q4.c: determine the required Zener diode voltage Vz; find a suitable value of the resistor R; determine the minimum requirement for the transistor power rating PTR. 2) What is the role of the resistor R in this circuit? Show your working throughout and state any assumptions you may make.Provide commentary to your design process, and evaluate your design.
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
Some electronic devices operate on a DC voltage of 7.5 V. To obtain 7.5 V DC from a 120-V (rms) AC line, first the voltage is dropped to 7.5 V (rms) AC by a transformer, and then the 7.5 V AC is converted to 7.5 V DC by a rectifier circuit involving diodes. Consider a device of resistance 15 Ω connected to the 7.5-V DC output of the rectifier. Again assuming no power loss anywhere, what is the rms current, in milliamperes, in the primary winding?
Design rectifier circuits to provide an output of100 VDC using a half wave rectifiercalculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply.
A 10 V Zener diode is used to regulate the voltage across a variable loadresistor. The input voltage Vs varies between 13 and16 V. The loadcurrent (??) varies between 10 and 85 mA. The minimum Zener current is15 mA. Findi. The maximum value of Rsii. The maximum power dissipated by the Zener diode, using the value ofRs.
Derive the current equations for the circuit shown below, using the labels as shown.Note that rz here is a model of the parasitic imperfection of the Zener diode.a) IL = ?b) II = ?c) IZ = ?d) What impact does rz have on VL?
What is the condition to obtain the maximum efficiency of a Rectifier? Neglecting the value of total resistance Neglecting the value of transformer resistance Neglecting the value of diode resistance Neglecting the value of load resistance
Design rectifier circuits to provide an output of100 VDC using a.) HWR b.) Center-tappedFWR and c.) Bridge-Type FWR circuits. For each circuit, calculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply
Can the regulator given in Figure Q4.b be used to regulate the output of a full-waverectifier, given the specifications for Io and Vpk in the Table 4 above? The rectifier voltage varies between 0.7Vpk and Vpk (that is, the ripple voltage is 30%of Vpk). The value of the Zener voltage Vz is 5.6 V, and the Zener diode power ratingis 2W. The regulator must supply to the load the current of at least Io mA. mA = 160 V = 22v To answer this question, you need to determine the value of the resistor R for theoutput requirements specification for Io and Vpk given in Table 4.
What is the maximum dc voltage you could expect to obtain from a transformer with an 18 Vrms secondary using a bridge rectifier circuit with a filter capacitor? in your own words
(i) With necessary sketch, write the load current flow path of a single phase semi converter during freewheeling period. Assume the load have resistance and high inductance value and the semi converter requires multiple gate pulse for triggering. (i) Draw the circuit diagram of the single phase half wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation.