Answered: 45) Find the RPM for turning a 1 1/4…

Engineering

Mechanical Engineering

45) Find the RPM for turning a 1 1/4 inch shaft on a lathe with the material having a cutting speed of 150 ft/min.

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter6: Milling

Section6.4: Indexing And Rotary Table Operations

Problem 6RQ: If the outside of a 6"-diameter disk is to be milled using a rotary table and a 3/4" diameter...

See similar textbooks

Related questions

Q: 1.In a steam power plant, steam enters the turbine at a pressure of 7 .2 Mpa and 550°C and exhaust…

Q: A rod subjected tensile stress is 15.92 x 10°N/mm2 and tensile strain is 0.01 then find young…

Q: 3. a) With neat diagram, State the principle of RTD sensor b) A platinum resistance thermometer has…

Q: A Carnot engine requires 40kJ/s from the hot source. The engine produces 20kW of power and the…

Q: Consider a simple ideal Brayton cycle with air as the working fluid. The pressure ratio of the cycle…

A: Given data as per the question The pressure ratio of the cycle = 7.2 Minimum temperature = 300 K…

Q: A schematic of a clutch-testing machine is shown. The steel shaft rotates at a constant speed w. An…

A: Torsional loading Those load which imparts the turning moment or the torque, is known as…

Q: Find Stress Force=3 N Cross sectional area=1 mm2

A: Given data : Force=F Cross sectional area=A Required : Stress

Q: Explain briefly the sorts of interruptions and why they are crucial to the machine.

Q: Assuming laminar flows, calculate the flow rate Q of an oil flowing from tank 1 (on the left) to…

A: Find the flow rate .

Q: A solid beam supported on bearings 15 ft apart, has a cross-section of 1/2 in deep and 3/8 in wide.…

A: As per the guidelines we will answer the first question for you, for the solution of other question…

Q: 4. On a winter's day the outside temperature of a 17-in thick concrete wall is -29°F, the wall is 15…

Q: Give examples of two different types of self-driving systems that might eventually take the place of…

A: Given question : Give examples of two different types of self-driving systems that might eventually…

Q: A load of 22 kips is gradually applied to a 2-in round rod, 10 ft long. The total elongation is…

A: Given dataLoad = 22 kips = 97860.88 NDiameter of section = 2 in = 0.0508 mLength of rod = 10 ft =…

Q: A metal bar 10 m long and weighs 50 N is supported at the 7 m mark by a fulcrum. A 100 N bag is…

Q: Consider a manufacturing system with two stations: (1) a load/unload station and (2) a machining…

A: Given : p = 1 f =1 To find : n

Q: What approach does a utilitarian would do if he/she is to solve the trolley problem (lever switch)?…

A: Given Trolley To find Utilitarian approach for trolley problem

Q: A car weighing 3000 lb, with a wheel base of 9 ft, carries 1400 lb of its load on the front wheels.…

Q: (b) Consider a simple ideal Brayton cycle with air as the working fluid. The pressure ratio of the…

Q: 9 cm 15 cm

Q: nd 45 KW at the final stage? 12.45 KW 13.57 KW 14.23 KW 15.14 KW

A: Actual power capacity.

Q: diesel fuel power plant is ed to the system which is

Q: 1N.S +flt) 1. Gcs) = X,Cs) FCs) Ikg lell %3D m

Q: 1. Solve for the Resultant vector using component and polygon method of the vectors below. a. 50 N…

Q: (b) Consider a simple ideal Brayton cycle with air as the working fluid. The pressure ratio of the…

Q: The motor A delivers 7500 kW to the shaft at 3600 rev/min, of which 2500 kW is removed by gear B and…

Q: Q2/ Four pipes A, B, C, and D form a system of pipes that connects two reservoirs A and B, as shown…

Q: 2, A diesel Cycle engine with k of 1.33 has an air standard efficiency of 60.5%. The temperature at…

Q: Cylinder B has a downward velocity in feet per second given by Vg = 2/2 + t°/6, where tis in…

Q: 3. A stationary minecart can be uniformly accelerated to a final speed of v upon passing through one…

Q: Find the value of kinetic energy if mass of car is 55 kg moving with velocity 23 m/s

A: Given data : Mass of car=m Velocity of car=V Required : Kinetic energy

Q: 10.37 A simple heat exchanger is turn bend on two 2-in Schedule 40 steel pipes as shown in Fig.…

A: The pressure difference between the inlet and the outlet of the tube can be calculated using the…

Q: A car travelling along a road is making a turn where the radius of curvature is r = 2t? m where t is…

A: Find the velocity and acceleration.

Q: Assuming laminar flows, calculate the flow rate Q of an oil flowing from tank 1 (on the left) to…

Q: Problem. If the force applied is perpendicular to the handle of the spanner as shown in the diagram,…

Q: (b) A steam power plant operates on an ideal reheat Rankine cycle between the pressure limits of 6…

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

A: Given data : Shear force=V Diameter=d Find : Shearing stress

Q: Find the work done if a force of 2 N displace crate of box by 2 m

A: Given data : Force=F Displacement=d To find : Work done

Q: A shortcompression memberwith Do= 2.5Di is to support a dead load of 25 tons. The material is to be…

A: Given Data The outer diameter and the ineer diameter relation is: Do=2.5Di The dead load acting on…

Q: A particle travels along a path where y = 8x3. The particle increases height with y = 27t3 where t…

Q: The two disks A and B have a mass of 3 kg and 5 kg, respectively. If they collide with the initial…

Q: What weld section properties are required to analyze the weld between the horizontal tube and the…

Q: Find maximum shear stress Maximum principal stress-8 MPa Minimum principal stress=3 MPa

Q: A aluminum tank with a wall thickness of 2mm and radius of 120mm is 9m long was pressurized to…

Q: 4. Briefly explain the two designs of tie rod ends and describe their function

Q: Two furces act 9. the compenent b. the magnitude he angles Gre, Q and Oz the resultant bolt at point…

Q: e steady state solution of the force -Damper with the following parame oing forcing function F(e).…

Q: (b) Consider a simple ideal Brayton cycle with air as the working fluid. The pressure ratio of the…

Q: Energy can be transferred either by heat or work. Consider a room that is heated as a result of…

A: To find : Is this a heat or work interaction for the room? Why?

Q: A metal bar 10 m long and weighs 50 N is supported at the 7 m mark by a fulcrum. A 100 N bag is…

Concept explainers

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.

Question

45) Find the RPM for turning a 1 1/4 inch shaft on a lathe with the material having a cutting speed of
150 ft/min.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given data

VIEW

Final solution

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the operation of straight turning in a lathe machine, the diameter of the workpiece is 80 mm, the length is 0.12 m, the cutting speed is 80 m / min, the feed is 0.5 mm / rev and the depth of cut is 0.002 m . Find the material removing rate and the time of machining.
For turning operation, using the table below, find an approximate value for the required speed of rotation of the chuck, in rpm, if the cutting speed for the material 5417 mm/s and the radius of the wp is 0.01 m. Show details of your answer. n | we| o
A part to be turned in an engine lathe must have a surface finish of 1.6 μm. The part is made of a free machining aluminum alloy. Cutting speed = 150 m/min. The nose radius on the tool = 0.75 mm. Determine the feed that will achieve the specified surface finish.
If a fairing operation is executed at a rotational speed of 40.0 rev / min, the feed is 0.015 in / rev and the depth of cut is 0.180 in, it determines: a) cutting time to complete the fairing operation; and b) the cutting speed; and c) The speed of metal removal at the beginning and end of the cut d) The power dissipated.
Figure and table given below shows the design details of a taper turning operation with a cutting speed of 22 m/ minute, feed 0.2 mm/ revolution; Depth of cut of 0.5 mm. (c) Time for n passes to complete taper turning in minutes .
It is required to cut screw threads of 2 mm pitch on a lathe. The lead screw has a pitch of 6 mm. If the spindle speed is 60 rpm, then the speed of the lead screw will be.
2 1.57 Show that, for the same shear angle, there are two rake angles that give the same cutting ratio.
In the machining operation with orthogonal cutting, the cutting plane angle is 9.5°, the cutting depth 0.4 mm, chip thickness 2.9 mm, cutting width 3.1 mm, shear strength 185 MPa in the process; a) Find the rake angle (α). b) Find the shear deformation (γ). c) Find the shear force. (Note: The shear force is 1.4 times the thrust.)
The cutting speed in in/min of a 12 mm drill operating at 600 rpm is nearly equal to
In a turning operation, the operator has established that a single pass on the cylindrical workpiece must be completed in 5.0 min. The piece is 400 mm long and 150 mm in diameter. Using a feed of 0.30 mm / rev and a depth of cut of 4.0 mm, what speed of cut should be used to meet this machining time?
Find the machining time, in seconds, and the rate of material removing in mmA3;sec for a turning operation having the following information: 1- Wp diameter is 80mm, 2- the length is 0.12m, 3- the cutting speed is 80m/min, 4- feed i50.5 mm/rev and 5- the depth of cut is 0.002m.
1.) On a lathe, a cylindrical work piece of 100mm diameter is being turned. The RPM is 100. The cutting speed is _________?(m/min)