47. Water enters a system of parallel piping at a rate of 500 GPM. The pipes length and inside diameter are L, = 10 ft, D¡ = 2.5 in, L= 20 ft, D2 = 3.0 in, L3 = 5 ft, D3 = 2 in, and L4 = 25 ft, D4 = 3.5 in. All pipes are smooth and loss coefficients are negligible. Find the diameter of the equivalent pipe. [Ans.: 6.06 in].

47. Water enters a system of parallel piping at a rate of 500 GPM. The pipes length and inside diameter are L, = 10 ft, D¡ = 2.5 in, L= 20 ft, D2 = 3.0 in, L3 = 5 ft, D3 = 2 in, and L4 = 25 ft, D4 = 3.5 in. All pipes are smooth and loss coefficients are negligible. Find the diameter of the equivalent pipe. [Ans.: 6.06 in].

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a cast-iron piping system of 450 ft length shown below, the rate of flow is 1 cfs at 70°F. Assuming the total head losses for the flow in the system is 10 ft, what is the energy head supplied by the pump E? a. 40 ft b. 50 ft c. 60 ft d. 510 ft e. None of the above
Suppose the pump of Fig. P14–23 is operating atfree delivery conditions. The pipe, both upstream and downstreamof the pump, has an inner diameter of 2.0 cm andnearly zero roughness. The minor loss coefficient associatedwith the sharp inlet is 0.50, each valve has a minor loss coefficientof 2.4, and each of the three elbows has a minor losscoefficient of 0.90. The contraction at the exit reduces thediameter by a factor of 0.60 (60% of the pipe diameter), andthe minor loss coefficient of the contraction is 0.15. Note thatthis minor loss coefficient is based on the average exit velocity,not the average velocity through the pipe itself. The total length of pipe is 6.7 m, and the elevation difference is (z1 - z2)= 4.6 m. Estimate the volume flow rate through this pipingsystem. Complete Answer, Thank you
The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?
Water at 16,2°C is to be discharged from a reservoir at a rate of 16,2 L/s using two horizontal cast iron (roughness value ɛ=0.00026m) pipes connected in series and a pump between them. The first pipe is 26,2 m long and has a 66,2 mm diameter, while the second pipe is 36,2 m long and has a 46,2 mm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged (KL=0.562), and losses associated with the connection of the pump are negligible. Neglecting the effect of the kinetic energy correction factor, determine the required pumping head, the minimum pumping power and electric motor power for total efficiency value of 76,2% to maintain the indicated flow rate. Water density is r=996,2 kg/m3, dynamic viscosity µ= 1.162x10-3kg/ms. Solve the problem by making the necessary assumptions and drawing the schematic figure.
04: Three pipes of diameters 300 mm, 200 mm and 400 mm and lengths 450 m, 255 m and 315 m, respectively, are connected in series. The difference in water surface levels in two tanks is 18 m. Determine the rate of water flow if coefficients of friction are 0.0075, 0.0078 and 0.0072, respectively, considering: (a) with minor losses, (b) without (neglecting) ‘minor losses.
4. Find the head loss in a pipeline consisting of 200 ft of 4-in steel pipe, a 90° bend on 24-in radius (K = 0.15), 4-in gate valve (fully open) (K = 0.20), 100 ft of 4-in steel pipe, expansion to 6 in with a 20° taper (K = 0.4), 300 ft of 6-in steel pipe, abrupt contraction to 3-in diameter (K = 0.35), and 50 ft of 3-in steel pipe. The discharge rate is 1.5 cfs.
In an annular section made of commercial steel pipe with an outer diameter or 13.78 inches inside a commercial steel pipe with an inner diameter of 23.62 inches carries a water flowrate of 600L/sec. The total length of the section is 10m. What is the frictional loss in meters of water at a temperature of 68o F?
9.7. Through a hydraulic turbine flow 2.8 m3/s of water. On the 1 m inlet pipe at elevation 43.5,a pressure gage reads 345 kPa. On the 1.5 m discharge pipe at elevation 39, a vacuum gage reads150 mm of mercury. If the total head lost through pipes and turbines between elevations 43.5and 39 is 9 m, what power may be expected from the machine?
Water at 20°C(?=998.3?? ????=1×10−6?2/?)flows through a galvanised iron pipe (? = 0.15 ??) with a diameter of 20 mm, entering the room at point A and discharging at point C from the fully opened gate valve B at a volumetric flow rate of 0.003 m3/s. Determine the required pressure at A, considering all the losses that occur in the system described in Figure Q1. Loss coefficients for pipe fittings have been provided in Table 1. L1 = 4 L2 = 1 L3 = 2.66 L4 = 1.34 L5 = 0.5 L6 = 1 Loss Coefficients Gate valve (fully opened) - 0.19 90 deg elbow - 0.9 45 deg bend - 0.4 Tee for valve along branch - 1.8
Water at 20°C (?=998.3kg/m3 ??? v =1×10−6?2/?) flows through a galvanised iron pipe (? = 0.15 ??) with a diameter of 20 mm, entering the room at point A and discharging at point C from the fully opened gate valve B at a volumetric flow rate of 0.003 m3/s. Determine the required pressure at A, considering all the losses that occur in the system described in Figure Q1. Loss coefficients for pipe fittings have been provided in Table 1. L1 = 4 L2 = 1 L3 = 2.66 L4 = 1.34 L5 = 0.5 L6 = 1 Table of Loss Coeffcients Loss Coeffcients KL Gate Valve - Fully Open 0.19 90° Bend 0.9 45° Bend 0.4 Tee for Valve along Branch 1.8
Water (@ 75°C) flows at a horizontal pipe at a rate of 1.6 m3/min in a pipe. Flow enters a 3 inch 45 deg. elbow and diverted upwards into a connecting pipe. The diameter of the outlet is 2 inches. If the pressure just before the elbow is 78kPa, what is the magnitude and direction of the force to keep the elbow in place? Assume: that frictional losses in the elbow are negligible.
Water flows naturally from a tank A located at 20 m above the ground level , to a ground leveltank B . The connecting pipeline between tank A and tank B has an equialent loss coefficient of K .Determine the flow rate Q= ? ( USE g= 10 m 2/s) Note that K0,5 : square root of K. ANSWER: 20 / K0,5 m3/s