Coefficient of Thermal Expansion Steel Rod (figure) a. Change in length if the rod is heated to 200°C. b. Change in diameter if Tf = 200°C. c. Thermal stress if the ends are rigidly supported (initially stress-free) and the rod is heated by 180°C. d. Determine the thermal expansion of the following materials: - Rubber - Silver - Copper - Aluminum - Steel

Coefficient of Thermal Expansion Steel Rod (figure) a. Change in length if the rod is heated to 200°C. b. Change in diameter if Tf = 200°C. c. Thermal stress if the ends are rigidly supported (initially stress-free) and the rod is heated by 180°C. d. Determine the thermal expansion of the following materials: - Rubber - Silver - Copper - Aluminum - Steel

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.6.13P: A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean...

See similar textbooks

Similar questions

A [0/90/0/±45]s Glass/Epoxy laminate is subjected to the following mechanical loads: Nx =Ny= 80*10^5 N/m. The thickness of each lamina is 0.25 mm. Longitudinal modulus of elasticity = E1 = 38.6 GPa , Transverse modulus of elasticity = E2 = 8.27 GPa , Poisons Ratio 0.26. a) Determine the local stresses at the top of 45° ply
A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m experiences a stress of 600 MPa when placed under tension. If the material used for the truss tie-rod has a Young's Modulus, E, of 5.8 x 1011 N/m?, calculate: (i) the tie-rod's extension in millimetres (mm); (ii) the strain energy (U) in Joules; and (ii) the strain energy per unit volume (U/V) in Joules per cubic metre (m³). Give your answers to two decimal places.
a 12mm thick steel tire has a width of 110mm and an internal diameter of 800mm. It is heated and shrunk onto a steel wheel 800.50mm in diameter. The modulus of elasticity of steel is 200gpa. Which of the following most nearly gives the comprehensive pressure between the tire and the wheel? A 3.30 mpa B 3.90 mpa C 3.75 mpa D 4.35 mpa
The internal and external diameters of a thick cylinder are 125 mm and 180 mm, respectively. It is subjected to an internal pressure of 150 MPa, E= 210 GPa and ν= 0.3. Calculate: (a) The radial stress at the inner surface. (b) The radial stress at the outer surface. (c) The hoop stresses in the cylinder at the inner and outer surface.
Calculate the change in dimensions in the bar.F = 12000 N; h= 0.01 m; w= 0.03 m; L = 0.8 m; E = 60 GPa; v = 0.3
If the Young's modulus and Poisson's ratio of the container material are 100 GPa and 0.3 respectively, What is the axial strain in the cylinder wall at mid-depth?
STRENGTH OF MATERIALS W/SOLUTION 1.) A penstock pipe 10m diameter carries water under a pressure head of 100m. If the wall thickness is 9mm, the tensile stress in the pipe wall is nearest to? A. 2725 B. 1090 C. 545 D. 110 E. NOTA
The diameter (d) of a solid rod (i.e., with a circular cross-section) is 16 mm and is made from a homogeneous material. The length (L) of the rod is 1.75 m and Young’s Modulus for the material (E) is 250 GPa. When the rod is placed under tension it experiences deformation and a stress (?) of 650 MPa. Calculate the following:(1) Strain energy (U) to 2 decimal places in Joules.(2) Strain energy per unit volume (U/V) in J/m3(3) The change in length ∆L to 2 decimal places in mm.(4) The strain (?) due to deformation to 2 significant figures. (show all work)
The assembly shown below consists of a brass shell (1) fully bonded to a ceramic core (2). The brass shell [E = 115 GPa; α = 18.7 x 10-6 /°C] has an outside diameter of 50 mm and an inside diameter of 35 mm. The ceramic core [E = 290 GPa; α = 3.1 x 10-6 /°C] has a diameter of 35 mm. At a temperature of 15°C, the assembly is unstressed. Determine the largest temperature increase that is acceptable for the assembly if the normal stress in the longitudinal direction of the brass shell must not exceed 80 MPa.
A steel rod is stretched between two walls. At 20C, the tensile force in the rod is 5000 N. If the stress is not to exceed 130 MPa at 20C. find the minimum allowable diameter of the rod. Use 18/deg Celsius and E = 200 GPa.
1. A solid piece of metal of volume 10,000 mm3 is compressed by a pressure of 70 MPa. Determine the bulk modulus given that the Young’s modulus E is 214 Gpa and the Poisson’s ratio is 0.33. Also determine the change in the volume.2. Starting from the first principles derive the relation between Young’s modulus (E), shear modulus (G) and Poisson’s ratio (υ)
A high-density polyethylene [E = 128 ksi; α= 88 x 10-6/°F; υ = 0.4] bar is positioned between two rigid supports. The bar is square with cross-sectional dimensions of 2.50 in. by 2.50 in. and length L = 48 in. At room temperature, a gap of Δ=0.25 in. exists between the block and the rigid support at B. After a temperature increase of 120°F, determine: a) The normal stress in the bar b)The lonitudinal strain in the bar. c)The transverse (ie lateral) strain in the bar.