5- A textile plant is supplied with 3-phase, 380 VII 50 Hz source. The loads of the plant are;Number of quantityOutput powerLoadsPower factor603 kWInduction motors0.8 lag6.50 KVA.O pf lead0.8 lag1 pfCapacitor bank470 kWInduction motors8.10 kWHeaterSourceCalculate the total current supplied by the sourceand power factor of the source.380 VOtherloadsMotorsLamps

Answered: Image /qna-images/answer/97e06310-d915-4ea9-a603-7f58f44c111d.jpg

5- A textile plant is supplied with 3-phase, 38 VII 50 Hz source. The loads of the plant are; Number of quantity Output power Loads Power factor 0.8 lag O pf lead 0.8 lag 1 pf 60 3 kW Induction motors 6. 50 kVAr Capacitor bank 470 kW Induction motors 8. 10 kW Heater Calculate the total current supplied by the source and power factor of the source. Source 380 V

5- A textile plant is supplied with 3-phase, 38 VII 50 Hz source. The loads of the plant are; Number of quantity Output power Loads Power factor 0.8 lag O pf lead 0.8 lag 1 pf 60 3 kW Induction motors 6. 50 kVAr Capacitor bank 470 kW Induction motors 8. 10 kW Heater Calculate the total current supplied by the source and power factor of the source. Source 380 V

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.24P: A source supplies power to the following three loads connected in parallel: (1) a lighting load...

See similar textbooks

Similar questions

Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
A 25 kVA, 240 V single phase source supply the rated power at the rated voltage to a motor at 0.8 power factor lagging. Find the capacitor bank in order to improve the power factor to 0.9 lagging connected to a motor.a. Calculate the real power, reactive power and current before capacitor bank is connected? b. Calculate the power and reactive power after capacitor bank is connected? c.What is kVA rating of capacitor bank QC?
AC electrical circuit is below: (refer picture below) a. Determine the current flowing in the load. b. If it is desired that the system power factor be 0.9. With system frequency = 50 Hz. Determine how large the capacitor is must be installed? Which one is correct? A/B/others answer A. C = 7.7015 mF B. C = 35.243 µF c. Please Draw all the phasor. Please give complete, details, and correct answer. Please do step by step, draw the phasor Please using handwriting (not typing ). THANK YOU, I WILL GIVE MANY THUMBS UP.
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the apparent power supplied by the generator. The apparent power supplied by the generator is _____ VA.
1. Solve for the equivalent impedance and admittance seen at the source. Solve for is(t). 2. A load Z draws 12 kVA at a power factor of 0.856 lagging from a 120-Vrms sinusoidal source. Calculate: (a) the average and reactive powers delivered to the load, and (b) the peak current.
1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
A 250V, 50 Hz single-phase supply feeds the following loads (i) incandescent lamps taking a current of 10A at unity power factor, (ii) fluorescent lamps taking 8A at a power factor of 0.7 lagging, (iii) a 3 kVA motor operating at full load and at a power factor of 0.8 lagging, and (iv) a static capacitor. Determine, for the lamps (incandescent and fluorescent) and motor, (a) the total current, (b) the overall power factor, and (c) the total power. (d) Find the value of the static capacitor to improve the overall power factor to 0.975 lagging.
A transmission line with impedance of 0.085 + j 0.32 Ω is used to deliver power to a load. The load is inductive and the load voltage is 200∠0° Vrms at 60Hz. If the load operates at 20 kVA with a power factor of 0.75 determine the real and quadrature power losses in both the load and the line and the source voltage phasor.
An industrial load of200KW has a powerfactor of 0.5 lagging. Agroup of synchronousmotors operating at apower factor of 0.8leading is installed andthe over-all power factorimproves to 0.75 lagging.Determine the KVArating of the synchronousmotors installed.Answer = 130.2354 KVA
A generating station has a maximum demand of 25,000 kW. Calculate the cost per unit generatedfrom the following data: Capital cost = P 120M; Annual load factor = 45%; Annual cost of fuel and oil = P6.5M ; Taxes, wagesand salaries etc. = P6M and Interest and depreciation = 13%
A residential four-wire system supplies power at220 V rms to the following single-phase appliances:On the first phase, there are ten 75-W bulbs. On thesecond phase, there is a 750-W vacuum cleaner with apower factor of 0.87. On the third phase, there are ten40-W fluorescent lamps with power factor of 0.64.Finda. The current in the netural wire.b. The real, reactive, and apparent power for eachphase.